voron_2_help_forum_public

tool head wire harness repair 12 messages

Apr 14, 2024, 9:05 PM Kits/parts advice Electronics & wiring

nighthawk 3 messages

Apr 14, 2024, 8:50 PM Configuration

Bed Higher In Middle Than On Sides 15 messages

Apr 14, 2024, 4:43 PM Bed mesh issue

Trapezoid shaped XY frame 5 messages

Apr 14, 2024, 2:49 PM Mechanical Kits/parts advice Initial setup

print layers not coming out right 3 messages

Apr 14, 2024, 2:23 PM First print

CW2 issue 12 messages

Apr 13, 2024, 9:23 PM Kits/parts advice

My Printer Destroyed My Bed Mid Print! 9 messages

Apr 13, 2024, 5:41 AM Mechanical

So, a thing happened… 27 messages

Apr 13, 2024, 4:05 AM Tuning Initial setup First print Tap Solved

Orca Slicer 33 messages

Apr 12, 2024, 12:49 PM Tuning Kits/parts advice First layer First print Configuration

I have a crazy Idea. I'm thinking about building a Delta style Voron. 2 messages

Apr 12, 2024, 12:07 AM Kits/parts advice

Issues with genuine HIWIN MGN9 10 messages

Apr 11, 2024, 7:39 PM Mechanical

r1 to r2 PIF upgrade 4 messages

Apr 11, 2024, 6:31 PM Kits/parts advice

Frame tolerance 3 messages

Apr 11, 2024, 5:58 PM Kits/parts advice

fan saver hotend mount vs standard hotend mount 2 messages

Apr 10, 2024, 7:54 PM Kits/parts advice

Voron 2.4 r2 Z printing in the air 4 messages

Apr 10, 2024, 6:57 PM Z Offset Solved Configuration

Voron 2.4 r2 Rev C Chamber Thermistor question 6 messages

Apr 10, 2024, 5:05 PM Kits/parts advice

Voron 2.4 ChaoticLabs CNC Tap installed, 14pin Molex issues repaired, Omron turns off w/ hotend on 55 messages

Apr 10, 2024, 1:06 AM Tap

Single wall looks perfect, calibration cube has bad layers 35 messages

Apr 9, 2024, 8:39 PM First print

I'm looking to build a large printer 14 messages

Apr 9, 2024, 12:24 AM Kits/parts advice Mechanical Electronics & wiring Configuration

Printer stinks really bad 16 messages

Apr 8, 2024, 7:09 PM Mechanical Kits/parts advice Solved Electronics & wiring

Gantry jumping 13 messages

Apr 8, 2024, 11:58 AM Mechanical

Extruder lifts on one side 7 messages

Apr 7, 2024, 6:34 PM Bed mesh issue First layer Solved

'mcu' shutdown ?? 3 messages

Apr 7, 2024, 5:50 PM Printer shutdown

octopus 1.1 not working anymore 4 messages

Apr 7, 2024, 3:03 PM Printer shutdown Solved Electronics & wiring

Voron 2.4r2 umbilical mod 4 messages

Apr 7, 2024, 11:54 AM Kits/parts advice Electronics & wiring

MCU 'EBBCan' shutdown: ADC out of range 7 messages

Apr 7, 2024, 5:05 AM Electronics & wiring

Klicky probe NG does not attach properly 42 messages

Apr 6, 2024, 11:11 PM Kits/parts advice Mechanical Electronics & wiring QGL

rapido extrusion failure 9 messages

Apr 6, 2024, 6:58 PM Tuning Mechanical First layer First print Configuration

There is something wrong with z3stepper 25 messages

Apr 6, 2024, 2:09 PM Z Offset Mechanical Initial setup

spyglass stopped working 3 messages

Apr 6, 2024, 3:41 AM Initial setup

Probe crashing only during bed mesh 52 messages

Apr 6, 2024, 12:53 AM Bed mesh issue Mechanical Tap Solved Configuration

Printer would change extrusion temperature randomly. 6 messages

Apr 5, 2024, 3:32 PM Configuration

bedmesh trouble 3 messages

Apr 5, 2024, 2:35 PM Mechanical

USB Camera (C920) pulling too much power from pi? 3 messages

Apr 5, 2024, 2:26 PM Electronics & wiring

LDO 0.2 Kit Bed fails to retract on home causing an error 3 messages

Apr 5, 2024, 11:58 AM Initial setup Electronics & wiring

V2.4 SB/TAP/CW2 ran out of filament overnight. Reload new spool, chaos. 13 messages

Apr 4, 2024, 8:56 PM Mechanical

When I try qgl i get the following message: No trigger on probe after full movement 6 messages

Apr 4, 2024, 10:24 AM QGL

Klicky - Don't Use Probe for Z Homing 4 messages

Apr 3, 2024, 8:19 PM Initial setup Configuration

z belt issue 37 messages

Apr 3, 2024, 2:51 AM Mechanical

first layer issue after gantry rebuild 44 messages

Apr 2, 2024, 2:54 AM Bed mesh issue Mechanical Tap Solved

MCU adc out of range 36 messages

Apr 1, 2024, 10:47 PM Solved Electronics & wiring

TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset) 4 messages

Apr 1, 2024, 8:35 PM Printer shutdown

Use a smaller build sheet? 6 messages

Apr 1, 2024, 5:07 PM Configuration

Best way to mount physical Y Enstop switch? 3 messages

Apr 1, 2024, 4:47 PM Electronics & wiring

Extrude below minimum temp | echo: "extruder" not hot enough 5 messages

Apr 1, 2024, 2:59 PM Configuration

Superslicer external perimeter problem. Help please? 4 messages

Mar 31, 2024, 11:14 PM Tuning

MCU adc out of rage 28 messages

Mar 31, 2024, 9:55 AM Printer shutdown

leviathan not picking up canbus toolhead board 34 messages

Mar 30, 2024, 10:50 PM Electronics & wiring Configuration

auto z_calibrate using klickypcb - 2mm too high? 41 messages

Mar 30, 2024, 9:39 PM Z Offset Configuration

Inconsistent first layer 4 messages

Mar 28, 2024, 10:26 PM Mechanical Z Offset First layer First print QGL