voron_2_help_forum_public

auto z_calibrate using klickypcb - 2mm too high? 41 messages

Mar 30, 2024, 9:39 PM Z Offset Configuration

Inconsistent first layer 4 messages

Mar 28, 2024, 10:26 PM Mechanical Z Offset First layer First print QGL

strange sound driver TMC2209 uart mode 4 messages

Mar 28, 2024, 3:28 PM Mechanical Electronics & wiring

panels rubbing on the gantry when chamber is hot 9 messages

Mar 27, 2024, 9:29 PM Mechanical

Help with Idle_timeout Macro 18 messages

Mar 27, 2024, 2:07 PM Solved Configuration

first layer test comes out weird 7 messages

Mar 27, 2024, 5:36 AM First layer

XY drive screws loose? 2 messages

Mar 26, 2024, 11:42 PM Kits/parts advice Mechanical

First print, what should I look at? 13 messages

Mar 26, 2024, 3:22 PM First print

gantry corners for custom size 49 messages

Mar 26, 2024, 7:46 AM QGL

Diagnosing terrible motor noise and performance 117 messages

Mar 26, 2024, 1:51 AM Mechanical Electronics & wiring Configuration

Fitment Issues with Stealthburner Cable Chain and Anchor 4 messages

Mar 25, 2024, 7:33 PM Mechanical Kits/parts advice Electronics & wiring

help on removing the adapter on dragonfly bmo 3 messages

Mar 25, 2024, 6:09 AM Kits/parts advice

Probe/Hotend Issue 22 messages

Mar 25, 2024, 3:17 AM Mechanical Electronics & wiring

Bed not heating 12 messages

Mar 24, 2024, 7:28 PM Electronics & wiring

klipper wont connect to mcu (formbot0.2 build) 2 messages

Mar 24, 2024, 8:43 AM Initial setup

Part cooling fan stops extrusion (Rapido 2) 11 messages

Mar 24, 2024, 5:32 AM Tuning

QGL issues 102 messages

Mar 23, 2024, 9:54 PM Mechanical

Double checking wiring 5 messages

Mar 23, 2024, 6:02 PM Electronics & wiring

printer shutdown after changing from 1.8° Steppers to 0.9° LDO 10 messages

Mar 23, 2024, 2:35 PM Mechanical Printer shutdown Electronics & wiring Configuration

Klipper update problems 21 messages

Mar 22, 2024, 10:30 PM Configuration

Bed Mesh 4 messages

Mar 22, 2024, 8:46 PM Bed mesh issue

voron 2.4 layer shift 5 messages

Mar 22, 2024, 8:16 PM Mechanical

adaptive bed mesh 17 messages

Mar 22, 2024, 3:43 PM Bed mesh issue

Uncontrolled Heater 16 messages

Mar 22, 2024, 1:32 PM Solved Electronics & wiring

2.4 bed location 6 messages

Mar 22, 2024, 8:52 AM Tuning Mechanical

bed not heating. state stuck at 60% 127 messages

Mar 21, 2024, 9:12 PM Electronics & wiring

What STL parts do i need for a Formbot 2.4R2 7 messages

Mar 21, 2024, 8:09 PM Kits/parts advice Initial setup

Spider -> Octopus replacement - Stepper Wiring 7 messages

Mar 21, 2024, 7:31 PM Electronics & wiring

110v/220v parts 3 messages

Mar 21, 2024, 1:50 PM Electronics & wiring

might be a long shot here but i'll give it a go. 5 messages

Mar 21, 2024, 1:20 PM Mechanical Electronics & wiring

weird QGL action 7 messages

Mar 21, 2024, 2:38 AM Mechanical QGL Configuration

Voron 2.4 R2 Pro (350) vs ShakeTune (IS) Bad messurements 9 messages

Mar 20, 2024, 3:15 PM Tuning Mechanical Tap Configuration

Inconsistent z offset 72 messages

Mar 20, 2024, 12:20 AM Z Offset

LDO Voron 2.4 r2 C / LDO Leviathan / ----- X/Y motor problems -- Initial build 9 messages

Mar 19, 2024, 3:24 PM Mechanical Initial setup Solved Electronics & wiring

X endstop position 3 messages

Mar 19, 2024, 10:31 AM Initial setup Configuration

canbus mcu and "printer not ready" error 4 messages

Mar 18, 2024, 12:02 AM Configuration

Sensorless Homing 66 messages

Mar 17, 2024, 10:04 PM Initial setup

Unable to correctly configure the Z offset 6 messages

Mar 17, 2024, 6:52 PM Z Offset First layer

inconsistent First Layer 48 messages

Mar 17, 2024, 6:39 PM Bed mesh issue First layer First print QGL

LDO Voron v2.4 r2 kit build questions 12 messages

Mar 17, 2024, 3:40 PM Kits/parts advice Mechanical

Lemon BTT Octopus board? 3 messages

Mar 17, 2024, 3:38 AM Electronics & wiring

usb printing issue 76 messages

Mar 17, 2024, 2:03 AM Configuration

Strange behavior during quad gantry level with tap Voron 2.4 r2 new build 30 messages

Mar 16, 2024, 11:15 PM Kits/parts advice

Sensorless Homing and Voron Tap 11 messages

Mar 16, 2024, 8:41 PM Tap Initial setup

Voron 2.4 Rev C Bed Not Heating 78 messages

Mar 16, 2024, 8:31 PM Electronics & wiring

short circuit, probably dead Octupus MCU? 4 messages

Mar 16, 2024, 12:53 PM Solved Electronics & wiring Configuration

Voron 2.4 not being able to print on entire bed 83 messages

Mar 15, 2024, 8:18 PM Bed mesh issue Tap First layer

Octopus red status light 2 messages

Mar 15, 2024, 6:48 PM Electronics & wiring

How to source a generic chain link end? 3 messages

Mar 15, 2024, 6:36 PM Mechanical Kits/parts advice

LDO Voron 2.4 R2 - 50W heater with standard cable 5 messages

Mar 15, 2024, 5:07 PM Electronics & wiring