ratos-support

How to increase led limit in RATOS 5 messages

Mar 9, 2026, 5:36 PM Solved Configuration Other

Filament Load/Unload Lenght 27 messages

Mar 7, 2026, 10:57 PM Configuration Customization

RatOS v2.1.0-RC 4 bugs and improvements 56 messages

Mar 7, 2026, 11:14 AM Macros Configuration Errors

Wiki Help 2 messages

Mar 7, 2026, 12:30 AM Configuration

Setup problems 13 messages

Mar 6, 2026, 1:16 PM Configuration

RatOS RC4-6 Update issue 26 messages

Mar 5, 2026, 6:32 AM Configuration

Z tilt is off position 7 messages

Mar 4, 2026, 3:08 AM Solved Configuration Motion

Bug Report: When configuring nozzle size, muse wheel must be deactivated. 4 messages

Mar 1, 2026, 10:23 AM Errors Configuration

Beacon calibration issue 6 messages

Feb 27, 2026, 5:04 PM Configuration

High load/unresponsive and /config not loading after fresh install of RC4 7 messages

Feb 26, 2026, 5:33 PM Solved Other

beacon unable to connect. 4 messages

Feb 24, 2026, 2:36 PM Errors

TMC5160 doesn't work with Manta M8P 25 messages

Feb 23, 2026, 11:31 PM Boards Errors Motion

RatOS 2.10 RC4 - Euclid Z-Offset Fail 10 messages

Feb 23, 2026, 4:00 PM Errors Configuration

RatOS 2.1.0-RC4 restore printer data 16 messages

Feb 22, 2026, 8:14 PM Configuration Other

Ratos 2.1-RC4 update - what is the configuration for the Vcore IDEX to enable loading/wiping nozzles 4 messages

Feb 21, 2026, 9:27 AM Solved Macros Configuration Errors

Dont detect Ldo NITEHAWK 36 in DFU 3 messages

Feb 18, 2026, 10:50 PM Configuration Boards

Voron 2.4 beacon calibrate crashes at the back of the bed. 4 messages

Feb 18, 2026, 1:54 AM Configuration Motion

RATOS update 2.x 7 messages

Feb 17, 2026, 12:54 PM Configuration Customization

where should i put this in the printer.cfg? 3 messages

Feb 17, 2026, 10:54 AM Configuration

Extruder Fan RatOS Speed setting. 6 messages

Feb 17, 2026, 2:23 AM Solved Configuration

New Rat Os install endtop issues 17 messages

Feb 16, 2026, 2:22 AM Errors Configuration Boards

Unable to open Mainsail after RC4 Configure run successfully 3 messages

Feb 15, 2026, 10:53 PM Solved Configuration

Join Spools on IDEX drops several lines of GCODE on tool change after filament runs out 4 messages

Feb 15, 2026, 12:46 AM Errors

VAOC Not Streaming After RC4 Upgrade 3 messages

Feb 14, 2026, 2:01 AM Solved Errors Configuration

Chamber heater not being used to heat chamber during beacon calibration 16 messages

Feb 11, 2026, 1:43 AM Solved Macros Configuration

How can I disable the new heat soaking feature? 4 messages

Feb 9, 2026, 3:46 AM Solved Configuration

Cannot complete setup after new install of RC4 12 messages

Feb 8, 2026, 9:35 PM Configuration

Turn on fans prior to "RatOS: Heating bed..." 4 messages

Feb 7, 2026, 4:59 PM Configuration Macros Customization

Adaptive heat soaking takes way too long 27 messages

Feb 6, 2026, 11:05 AM Errors Configuration

probe samples exceed sample tolerance. 8 messages

Feb 4, 2026, 9:47 PM Errors Configuration Motion

RatOS 2.1 New Install 7 messages

Feb 4, 2026, 4:01 AM Configuration

Etcher Issue 6 messages

Feb 4, 2026, 3:01 AM Configuration

Homing problems on RC4-5 clean install 134 messages

Feb 3, 2026, 4:54 PM Motion

Link is broken for upgrade guide read first 4 messages

Feb 3, 2026, 7:19 AM Configuration

CPU governor check 31 messages

Feb 2, 2026, 10:24 PM Errors

Move out of range when canceling or finishing every print 6 messages

Feb 1, 2026, 11:38 PM Macros Configuration Motion

mcu rpi shutdown. Where is the internal rpi mcu used? 24 messages

Jan 31, 2026, 8:43 AM Errors Configuration

SAVE_CONFIG after PID Issue 13 messages

Jan 30, 2026, 2:58 PM Macros

RatOS Shutdown does not shut down Octopus 4 messages

Jan 30, 2026, 2:56 PM Macros

Boxturtel will direkt Filament wechseln 4 messages

Jan 28, 2026, 12:57 PM Macros Configuration

Option 'pullup_resistor' is not valid in section 'extruder' 5 messages

Jan 27, 2026, 6:23 PM Solved Errors Customization Boards

IDEX Parking - loading and unloading 46 messages

Jan 22, 2026, 4:11 PM Macros Motion

RatOS 2.1.RC3-30 and EBB42 Gen2 16 messages

Jan 18, 2026, 4:25 PM Solved Configuration

V-Minion 1.0 - Y Axis homing to the front on latest RatOS 1.1 RC3 9 messages

Jan 17, 2026, 1:16 PM Configuration Motion

Micro SD card 2 messages

Jan 17, 2026, 2:12 AM Configuration

setup wizard help please 114 messages

Jan 16, 2026, 10:25 PM Solved Configuration

Speed factor resetting during IDEX printing 5 messages

Jan 16, 2026, 4:45 PM Macros Configuration Customization

BTT Manta M8P CB1 update to ratos 2.1.0 RC2 11 messages

Jan 14, 2026, 2:09 AM Configuration Boards

Getting "Extrude only move too long (-1197.654mm vs 200.000mm)" with M600 macro 5 messages

Jan 10, 2026, 10:14 PM Macros Errors

Mesh loading macro 2 messages

Jan 10, 2026, 5:34 PM Macros