ratos-support

RatOS Shutdown does not shut down Octopus 4 messages

Jan 30, 2026, 2:56 PM Macros

Boxturtel will direkt Filament wechseln 4 messages

Jan 28, 2026, 12:57 PM Macros Configuration

Option 'pullup_resistor' is not valid in section 'extruder' 5 messages

Jan 27, 2026, 6:23 PM Solved Errors Customization Boards

IDEX Parking - loading and unloading 46 messages

Jan 22, 2026, 4:11 PM Macros Motion

RatOS 2.1.RC3-30 and EBB42 Gen2 16 messages

Jan 18, 2026, 4:25 PM Solved Configuration

V-Minion 1.0 - Y Axis homing to the front on latest RatOS 1.1 RC3 9 messages

Jan 17, 2026, 1:16 PM Configuration Motion

Micro SD card 2 messages

Jan 17, 2026, 2:12 AM Configuration

setup wizard help please 114 messages

Jan 16, 2026, 10:25 PM Solved Configuration

Speed factor resetting during IDEX printing 5 messages

Jan 16, 2026, 4:45 PM Macros Configuration Customization

BTT Manta M8P CB1 update to ratos 2.1.0 RC2 11 messages

Jan 14, 2026, 2:09 AM Configuration Boards

Getting "Extrude only move too long (-1197.654mm vs 200.000mm)" with M600 macro 5 messages

Jan 10, 2026, 10:14 PM Macros Errors

Mesh loading macro 2 messages

Jan 10, 2026, 5:34 PM Macros

ADC out of range, heater bed temperature 2 messages

Jan 10, 2026, 12:28 PM Errors Configuration

Fails during Updates 3 messages

Jan 5, 2026, 3:00 PM Errors

RatOS Klipper 13 2 messages

Jan 2, 2026, 10:00 PM Other

Z offset fine in manual control, off during print 6 messages

Dec 31, 2025, 9:10 PM Configuration Motion

Z tilt & z offset problem with idex. 4 messages

Dec 29, 2025, 7:22 PM Motion

Ratos print start macros sequence 4 messages

Dec 24, 2025, 1:20 PM Macros Customization

Klipper shutdown MCU 'mcu' shutdown: Timer too close 13 messages

Dec 23, 2025, 12:24 AM Errors

IDEX Machine, RatOS start_print macros always heat T0, even when not used 6 messages

Dec 16, 2025, 3:34 PM Configuration

moonraker dead after last ratos update 4 messages

Dec 16, 2025, 10:14 AM Solved Errors

Pause on Start Print 3 messages

Dec 16, 2025, 6:23 AM Errors Configuration

Is there any way to get belt measuring tool work again on CB1 ? 3 messages

Dec 15, 2025, 12:09 PM Errors Macros

#V-core 4 IDEX part cooling fan speeds 3 messages

Dec 14, 2025, 10:36 PM Configuration

Lost VAOC Camera 8 messages

Dec 14, 2025, 3:14 AM Errors

Lower bed more with end print 4 messages

Dec 10, 2025, 10:33 AM Configuration

Disable automatically overwriting the ratos.cfg/other ratos files 13 messages

Dec 9, 2025, 9:29 PM Configuration

Wifi issue 2 messages

Dec 6, 2025, 6:47 AM Configuration Boards

Tmc5160T v1.0 not pro need to set extruder as 36 volt #ratos 4 messages

Dec 5, 2025, 8:01 PM Solved Configuration Customization Boards

strange error.. 2 messages

Dec 2, 2025, 11:37 AM Configuration

Cant choose 48v for BTT TMC5160(T) Pro v1.1 2 messages

Dec 1, 2025, 7:54 PM Configuration

Pre-processor aborting print 3 messages

Nov 29, 2025, 2:04 PM Other

Printer won’t boot up 5 messages

Nov 27, 2025, 4:18 PM Other

VAOC calibration - toolheads move to the front!!!! 2 messages

Nov 24, 2025, 7:43 PM Configuration Motion

RatOS is not respecting the Minimal Chamber temperature? 7 messages

Nov 21, 2025, 9:51 PM Solved Other

Definition Fans 4 messages

Nov 17, 2025, 1:42 PM Configuration

Unknown pin chip name 'multi_pin' 18 messages

Nov 12, 2025, 5:28 PM Solved Errors

pin PA0 used multiple times in config 2 messages

Nov 10, 2025, 10:59 PM Configuration

HOTEND HEATER PIN connection - Vcore 3.1 RatOs 2.1 4 messages

Nov 7, 2025, 1:45 PM Customization

mpu9250 for ratos 3 messages

Nov 2, 2025, 2:47 PM Configuration Customization

Add NoIR Camera Ratos 2.1 3 messages

Nov 2, 2025, 12:17 PM Solved Customization Other

Wifi disconnect issue, sonar breaks VAOC 13 messages

Oct 30, 2025, 1:28 PM Errors

move out of range: 460.038 11 messages

Oct 27, 2025, 2:30 AM Configuration

Camera not present 5 messages

Oct 24, 2025, 1:56 AM Errors Configuration

Problem with RatOS config 31 messages

Oct 21, 2025, 4:06 PM Configuration

First layer inconsistencies in Z-offset 26 messages

Oct 21, 2025, 6:52 AM Errors Motion

Issues connecting to wifi for the first time 14 messages

Oct 20, 2025, 7:07 PM Solved Configuration

MAC Address 2 messages

Oct 17, 2025, 2:47 AM Configuration

Anyone know how to re-flash the toolboards for the IDEX Build? 3 messages

Oct 15, 2025, 9:40 PM Solved Boards

adxl usb - klipper stuck in restart 7 messages

Oct 15, 2025, 2:45 PM Configuration