ratos-support

RatOS/MCU/Klipper failure after update (Octopus Pro 446) 31 messages

Jul 24, 2024, 5:49 PM Configuration Boards

Getting Incomplete Slicer Configuration detected 22 messages

Jul 24, 2024, 2:17 PM Solved Errors

support fly Gemini boards 6 messages

Jul 24, 2024, 8:33 AM Solved Boards

Getting started & maybe files missing? 9 messages

Jul 24, 2024, 7:14 AM Configuration

octopus pro wont detect on setup and unable to compile data to flash board 50 messages

Jul 23, 2024, 10:06 PM Solved Configuration Boards Other Errors

Move exceeds maximum extrusion 2 messages

Jul 22, 2024, 7:47 PM Errors Configuration

Prime blob on 300 size v4 is in the way 5 messages

Jul 21, 2024, 3:35 PM Solved Other

1mm nozzle prime blob dangerously big 13 messages

Jul 21, 2024, 1:49 PM Errors Configuration

uh oh in configurator v2.1.0-RC1-33 [current values] 18 messages

Jul 21, 2024, 10:05 AM Configuration

pullup_resistor :ERROR 60 messages

Jul 20, 2024, 3:59 PM Solved Errors

Does RatOS RC1 flashing delete bootloader? 6 messages

Jul 19, 2024, 8:06 PM Solved Boards

EBB 42 2 port hotend fan isn't working. 7 messages

Jul 19, 2024, 5:04 AM Solved Configuration Boards

No more correct print since update 2.1 54 messages

Jul 18, 2024, 10:04 PM Macros Configuration

Making changes in RatOS 2.1 configurator? 32 messages

Jul 18, 2024, 10:00 PM Macros Configuration

Meaning of red and green in config changes 56 messages

Jul 18, 2024, 6:34 PM Configuration

Gantry Slams into Front Belt Tensioners 111 messages

Jul 18, 2024, 4:29 PM Solved Configuration

Last RatOS.cfg issue 11 messages

Jul 18, 2024, 4:19 PM Solved Motion

BIGTREETECH Pi 2 with RatOS 3 messages

Jul 18, 2024, 1:29 PM Solved Configuration

I want to Update RatOS v2.0.2 to v2.1.0 RC1 44 messages

Jul 17, 2024, 5:12 PM Solved Configuration Customization

Failed Beacon Poke test 46 messages

Jul 17, 2024, 1:28 AM Configuration

Nitehawk-36 Toolheadboard 332 messages

Jul 16, 2024, 11:17 PM Solved Configuration Customization

Updating to 2.1 configuration issue 56 messages

Jul 16, 2024, 10:45 PM Configuration

Retraction Settings 9 messages

Jul 16, 2024, 3:29 PM Solved Configuration

Configuration changes needed for a 150x150 bed 9 messages

Jul 16, 2024, 11:57 AM Solved Configuration Other

beacon firmware 6 messages

Jul 16, 2024, 6:55 AM Errors Configuration

Error during beacon ratos calibration 3 messages

Jul 16, 2024, 5:20 AM Macros Configuration Errors

v2,1 Install problems. 50 messages

Jul 15, 2024, 5:32 PM Errors

RatOS v2.1: Error during accelerometer data streaming 40 messages

Jul 15, 2024, 12:47 PM Solved Configuration Customization

Error during homing contact on repeated prints 114 messages

Jul 14, 2024, 11:42 PM Configuration

Crowsnest webrtc stream stays on after site is closed on android (chrome & firefox) 2 messages

Jul 14, 2024, 8:21 PM Solved Other

Nozzle Temp is jumping around 4 messages

Jul 14, 2024, 2:39 PM Errors Other

Where is RatOS 2.1?!!!!! 74 messages

Jul 13, 2024, 7:55 PM Solved Configuration

RatOS Manta CB1 - Repeated "Timer too close" Failures 13 messages

Jul 13, 2024, 2:39 PM Errors Boards

Error when trying to flash ratos 2.0 11 messages

Jul 13, 2024, 6:38 AM Solved Errors Configuration

Mainsail gcode viewer doesn't working correct 4 messages

Jul 13, 2024, 5:34 AM Solved Errors Other

Must home axis first: 249.700 250.000 15.000 [3526.412] 8 messages

Jul 12, 2024, 6:38 PM Errors Configuration Motion

Z tilt with Beacon Probes at 235 3 messages

Jul 11, 2024, 11:39 PM Solved Configuration

unload 24 messages

Jul 11, 2024, 8:54 PM Solved Configuration

Engines hum and heat up a lot with Kraken and RatOS2.1 161 messages

Jul 11, 2024, 6:27 PM Errors Boards

I removed ebb42 and now I can't use the printer 5 messages

Jul 11, 2024, 2:31 PM Errors Configuration Boards

Wifi Connection not working since Update 49 messages

Jul 9, 2024, 8:25 PM Solved Errors

Realtime Analysis not working with BTT lis2dw card 29 messages

Jul 9, 2024, 5:03 PM Solved Configuration Boards Errors Motion

RatOs2.1 flash fails after 2.0.2 succeded 16 messages

Jul 9, 2024, 2:20 AM Solved Errors Configuration

How Can I delay the activation of the filament sensor until after the prime blob - will this work? 3 messages

Jul 8, 2024, 4:29 PM Solved Configuration

Hotend fan temperature control 17 messages

Jul 6, 2024, 9:07 PM Solved Configuration

Is the new BTT CB2 compatible with ratos? 8 messages

Jul 6, 2024, 5:36 AM Solved Configuration

Btt Kraken definition files contain references to octopus-max-ez? 6 messages

Jul 6, 2024, 4:21 AM Solved Configuration

Multiple IP addresses assigned to one printer? 6 messages

Jul 5, 2024, 9:02 PM Errors

RatOs 2.1 4 messages

Jul 5, 2024, 8:57 PM Solved Errors

How do I get a mouse pointer for RatOS? 4 messages

Jul 4, 2024, 2:20 PM Configuration