ratos-support

Failed Beacon Poke test 46 messages

Jul 17, 2024, 1:28 AM Configuration

Nitehawk-36 Toolheadboard 332 messages

Jul 16, 2024, 11:17 PM Solved Configuration Customization

Updating to 2.1 configuration issue 56 messages

Jul 16, 2024, 10:45 PM Configuration

Retraction Settings 9 messages

Jul 16, 2024, 3:29 PM Solved Configuration

Configuration changes needed for a 150x150 bed 9 messages

Jul 16, 2024, 11:57 AM Solved Configuration Other

beacon firmware 6 messages

Jul 16, 2024, 6:55 AM Errors Configuration

Error during beacon ratos calibration 3 messages

Jul 16, 2024, 5:20 AM Macros Configuration Errors

v2,1 Install problems. 50 messages

Jul 15, 2024, 5:32 PM Errors

RatOS v2.1: Error during accelerometer data streaming 40 messages

Jul 15, 2024, 12:47 PM Solved Configuration Customization

Error during homing contact on repeated prints 114 messages

Jul 14, 2024, 11:42 PM Configuration

Crowsnest webrtc stream stays on after site is closed on android (chrome & firefox) 2 messages

Jul 14, 2024, 8:21 PM Solved Other

Nozzle Temp is jumping around 4 messages

Jul 14, 2024, 2:39 PM Errors Other

Where is RatOS 2.1?!!!!! 74 messages

Jul 13, 2024, 7:55 PM Solved Configuration

RatOS Manta CB1 - Repeated "Timer too close" Failures 13 messages

Jul 13, 2024, 2:39 PM Errors Boards

Error when trying to flash ratos 2.0 11 messages

Jul 13, 2024, 6:38 AM Solved Errors Configuration

Mainsail gcode viewer doesn't working correct 4 messages

Jul 13, 2024, 5:34 AM Solved Errors Other

Must home axis first: 249.700 250.000 15.000 [3526.412] 8 messages

Jul 12, 2024, 6:38 PM Errors Configuration Motion

Z tilt with Beacon Probes at 235 3 messages

Jul 11, 2024, 11:39 PM Solved Configuration

unload 24 messages

Jul 11, 2024, 8:54 PM Solved Configuration

Engines hum and heat up a lot with Kraken and RatOS2.1 161 messages

Jul 11, 2024, 6:27 PM Errors Boards

I removed ebb42 and now I can't use the printer 5 messages

Jul 11, 2024, 2:31 PM Errors Configuration Boards

Wifi Connection not working since Update 49 messages

Jul 9, 2024, 8:25 PM Solved Errors

Realtime Analysis not working with BTT lis2dw card 29 messages

Jul 9, 2024, 5:03 PM Solved Configuration Boards Errors Motion

RatOs2.1 flash fails after 2.0.2 succeded 16 messages

Jul 9, 2024, 2:20 AM Solved Errors Configuration

How Can I delay the activation of the filament sensor until after the prime blob - will this work? 3 messages

Jul 8, 2024, 4:29 PM Solved Configuration

Hotend fan temperature control 17 messages

Jul 6, 2024, 9:07 PM Solved Configuration

Is the new BTT CB2 compatible with ratos? 8 messages

Jul 6, 2024, 5:36 AM Solved Configuration

Btt Kraken definition files contain references to octopus-max-ez? 6 messages

Jul 6, 2024, 4:21 AM Solved Configuration

Multiple IP addresses assigned to one printer? 6 messages

Jul 5, 2024, 9:02 PM Errors

RatOs 2.1 4 messages

Jul 5, 2024, 8:57 PM Solved Errors

How do I get a mouse pointer for RatOS? 4 messages

Jul 4, 2024, 2:20 PM Configuration

After Toolchange in Idex print Firmware restart 13 messages

Jul 4, 2024, 2:08 PM Solved Configuration

BTT MICROPROBE 20 messages

Jul 4, 2024, 11:46 AM Configuration

update speed stupidity slow 39 messages

Jul 1, 2024, 10:46 PM Other

Logitec Brio webcam 4 messages

Jul 1, 2024, 7:46 PM Errors Configuration

RatOS 2.1.0 RC1 from 2024-06-21 - why does the RatOs Hotspot password raspberry don't work 2 messages

Jul 1, 2024, 7:30 PM Solved Errors

Cannot connect to Klipper 17 messages

Jul 1, 2024, 2:33 PM Solved Errors Configuration Boards

Getting this error on each layer: Unknown command:"_ON_LAYER_CHANGE 8 messages

Jun 30, 2024, 5:00 PM Solved Errors Configuration

x endstop help 6 messages

Jun 30, 2024, 4:17 PM Configuration

Reverse pin logic question 13 messages

Jun 30, 2024, 2:30 AM Customization

Cannot get 2.1 to work on new install 5 messages

Jun 29, 2024, 8:14 PM Solved Configuration Boards

Macro for getting the Hybrid belts result in crashing 58 messages

Jun 29, 2024, 2:59 PM Macros

4 pin Part cooling Fan not turning on. 49 messages

Jun 28, 2024, 10:31 PM Solved Macros Configuration

Triangellab Euclid: Shutdown due to expected probe state to be stowed but is deployed (0) 39 messages

Jun 27, 2024, 10:21 AM Configuration Macros Errors Customization Motion

No BEACON_INITIAL_CALIBRATION on vc-4.0 installation 15 messages

Jun 26, 2024, 5:06 PM Solved Errors Configuration

Has any used the adxl built into the EBB42 for input shaper? 8 messages

Jun 25, 2024, 11:57 PM Solved Configuration Customization Boards

4028 Inverted behavior on EBB42. Even with !fan_part_cooling_pin 33 messages

Jun 25, 2024, 2:47 PM Configuration

Euclid with brush Macro Configuration 5 messages

Jun 25, 2024, 2:07 PM Configuration Macros Errors Customization Motion

Flashed the wrong board in the configurator, how to remove it? 13 messages

Jun 24, 2024, 5:54 PM Solved Configuration Boards

Help! How do I make my IP static? 4 messages

Jun 23, 2024, 9:02 PM Solved Configuration Customization