fix-my-printer

New hot end, incorrect temperature reading with hotend off.. 8 messages

Feb 13, 2023, 5:43 PM other

Connecting two board fans to the Octopus 1.1 12 messages

Feb 13, 2023, 5:06 PM setup

Long pause after print line 3 messages

Feb 12, 2023, 4:39 PM other

extruder thermistor problem and changing pin 2 messages

Feb 10, 2023, 10:53 PM setup

Sensorless Homing 11 messages

Feb 10, 2023, 6:18 AM motion

Z-TILT-ADJUST fails with weird movement 7 messages

Feb 9, 2023, 6:12 PM motion

Deep Resonance 102 messages

Feb 9, 2023, 12:48 AM other

Connecting a 12V 4 pin part fan 12 messages

Feb 8, 2023, 8:36 PM setup

Hotend and Bed Temp Issues? 19 messages

Feb 8, 2023, 6:00 PM setup

Bed level issue? 4 messages

Feb 8, 2023, 6:00 PM setup

V-Minion Y axis chattering, not homing 6 messages

Feb 8, 2023, 2:38 AM motion

VCore 3.1 resonance on horizontal moves 29 messages

Feb 7, 2023, 9:10 PM motion

How to address Z binding? 3 messages

Feb 6, 2023, 1:56 PM motion

Bl-touch not working 11 messages

Feb 6, 2023, 5:35 AM other

Carriage slowly drifting to rear left 94 messages

Feb 5, 2023, 7:10 AM motion

electronic subframe too high? 2 messages

Feb 4, 2023, 7:37 PM setup

Over temperature TMC2209 error even with replacement TMC2209 26 messages

Feb 4, 2023, 5:00 PM motion other setup

mosquito hotend verify heater problem 9 messages

Feb 4, 2023, 8:58 AM setup

Bed temperature not stable (Keenovo 157 220V 600W) 45 messages

Feb 3, 2023, 10:00 PM other

Attempt Z Tilt -- Print Head Hitting Bed 7 messages

Feb 2, 2023, 7:28 AM motion setup

ADXL345 38 messages

Feb 1, 2023, 6:01 PM setup

Printer paused after print start 6 messages

Jan 31, 2023, 3:32 PM setup

Back right stepper clicking 3 messages

Jan 31, 2023, 3:10 PM motion

after update Problem, mcu unable to connect 5 messages

Jan 31, 2023, 12:27 PM other

Gantry Misalignment V-Core 500 7 messages

Jan 31, 2023, 10:56 AM motion

The circle is not standard 30 messages

Jan 31, 2023, 4:46 AM other

Error for updating system packages 12 messages

Jan 30, 2023, 11:12 PM setup

Printer moves extremely slowly when resuming from pause 2 messages

Jan 30, 2023, 8:20 AM other setup

Correct g-code flavor for prusaslicer and klipper? 4 messages

Jan 28, 2023, 1:55 PM motion

Manta M8P + CB1 Stepper Error 12 messages

Jan 28, 2023, 11:24 AM motion setup

Part Cooling Fan and extrusion issues 23 messages

Jan 28, 2023, 12:36 AM setup

Rattling X/Y axis 6 messages

Jan 27, 2023, 3:56 PM motion

Help with BTT Smart Filament Sensor config V-Minion 30 messages

Jan 26, 2023, 11:13 AM setup

Note: Raspberry Pi Cam Module 3 - Not compatible with RatOS 2 messages

Jan 25, 2023, 12:38 PM other

Heater heater_bed not heating 9 messages

Jan 25, 2023, 9:16 AM other

What do all of you do to keep the hot end wires from dragging on the bed? 21 messages

Jan 24, 2023, 4:39 PM setup

Play on X's linear rail 11 messages

Jan 24, 2023, 7:23 AM motion

Bed and Hot End Will Not Heat Up 11 messages

Jan 23, 2023, 7:04 PM setup

RatOS will not connect to my mcu 87 messages

Jan 22, 2023, 11:30 PM setup

V-Minion Z-Offset, first layer, chamber problem 46 messages

Jan 22, 2023, 8:11 PM other

octopus 1.1 is it fried? 4 messages

Jan 22, 2023, 2:16 PM other

Skr 2 powering issues 3 messages

Jan 22, 2023, 2:04 AM setup

ebb36 heater always on 4 messages

Jan 21, 2023, 2:43 PM setup

4028 always 100% 4 messages

Jan 21, 2023, 2:19 PM setup

Super Pinda Problems 19 messages

Jan 21, 2023, 7:06 AM setup

VC-3.1 500 - belt jumping out of flange 19 messages

Jan 20, 2023, 7:50 AM motion

MY 4028 FAN DOESN'T SHUT OFF AT 0% 2 messages

Jan 20, 2023, 1:22 AM setup

Did a full reinstall of Klipper and Board firmware 2 messages

Jan 19, 2023, 11:37 PM setup

Extruder not Working During Print 3 messages

Jan 19, 2023, 3:46 PM motion

4028 Hookup Sanity Check 49 messages

Jan 19, 2023, 4:43 AM setup