fix-my-printer

Input shaper not work 6 messages

Mar 10, 2023, 6:25 PM setup

Klipper screen shows menu, but touch screen won't react after ratos2.0 update 4 messages

Mar 9, 2023, 11:17 PM setup

Ratos board selection 3 messages

Mar 9, 2023, 6:27 PM setup

Heater extruder not heating at expected rate 3 messages

Mar 9, 2023, 6:19 PM other

RatOS v2.0.0... now unable to join network "RatOS" 4 messages

Mar 9, 2023, 5:04 PM setup

octopus v1.1 bootloader 4 messages

Mar 9, 2023, 12:26 AM setup

Octopus 1.1 firworks 22 messages

Mar 7, 2023, 2:04 AM setup

Burning hotend - Rapido 8 messages

Mar 6, 2023, 7:18 PM other setup

How to update firmware on Octopus 429? 14 messages

Mar 5, 2023, 12:27 PM other

XY Stepper error 7 messages

Mar 5, 2023, 9:50 AM motion

XY axis scale wrong 2 messages

Mar 5, 2023, 12:36 AM motion

cant connect to klipper 8 messages

Mar 4, 2023, 7:51 PM other

Z_TILT_ADJUST - Impossible to complete. 34 messages

Mar 4, 2023, 6:20 PM motion setup

Rescue print after Power outage 6 messages

Mar 4, 2023, 5:30 PM other

Rapido UHF can 't reach more than 226 °C 3 messages

Mar 4, 2023, 11:19 AM other setup

G28 Home all behavior 6 messages

Mar 4, 2023, 4:34 AM setup

Rescue timelapse after Power failure 12 messages

Mar 3, 2023, 12:20 PM other

Extruder E-Steps Calibration 7 messages

Mar 2, 2023, 6:29 PM setup

Probe triggered prior to movement 68 messages

Mar 2, 2023, 1:21 PM motion setup

Belt path out of whack 56 messages

Mar 2, 2023, 8:45 AM motion

pin PC7 is an alias for z1_uart_pin 2 messages

Feb 28, 2023, 9:18 PM motion setup

TMC 2209 Driver Error 20 messages

Feb 28, 2023, 4:13 PM other

Heater disconnected from heating block 7 messages

Feb 27, 2023, 11:47 PM other

After Trying Move Home x-y got error message 11 messages

Feb 27, 2023, 8:52 PM motion setup

Right Motor idler assembly 28 messages

Feb 26, 2023, 3:07 AM motion

4028 PWM not working 10 messages

Feb 25, 2023, 11:22 AM other

Heating extruder not heating at expected rate 7 messages

Feb 24, 2023, 9:08 PM other

Part cooling not turning on when printing 3 messages

Feb 24, 2023, 8:02 PM other

V Core 3 CAN communication configuration 9 messages

Feb 24, 2023, 6:01 PM setup

Linear rail and Lead Screw lubrication 19 messages

Feb 24, 2023, 11:14 AM other

PETG melting between LGX and Mosquito Magnum 16 messages

Feb 23, 2023, 10:39 PM other

Belts rubbing against idler 8 messages

Feb 23, 2023, 10:28 PM motion

TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset) 5 messages

Feb 23, 2023, 3:45 AM motion other

Z-Tilt Fails 4 messages

Feb 23, 2023, 12:58 AM motion setup

my v minion is noise 4 messages

Feb 22, 2023, 8:40 PM motion

Klipper won't start. 4 messages

Feb 22, 2023, 8:28 PM setup

Belt move too low and goes over flange 20 messages

Feb 22, 2023, 2:27 PM motion

Tightening belts causes y-rail noise Vcore3 6 messages

Feb 22, 2023, 2:35 AM motion

Help! I am loosing my mind over the ugly layer issue. V-Minion. 28 messages

Feb 21, 2023, 9:53 PM other

'RatOS invalid' in update-tab 10 messages

Feb 21, 2023, 8:00 PM other setup

Lubricating the linear rails with 3 in 1 oil 9 messages

Feb 21, 2023, 7:51 PM setup

configuration 160 messages

Feb 19, 2023, 10:28 PM setup

Belt Erosion 4 messages

Feb 18, 2023, 2:42 AM other

occasional layer shift / Belt shifting 54 messages

Feb 17, 2023, 6:44 PM motion

I need a fresh approach for my extruder clacking. (V-Core 3.0 400 with Duet Board) 7 messages

Feb 17, 2023, 5:38 PM other

BTT filament sensor keeps showing "empty" after a few seconds 5 messages

Feb 16, 2023, 9:12 PM other

wired print artifacts 5 messages

Feb 16, 2023, 1:55 PM other

V-Core 500 3.0 -- 3.1 Upgrade Woes 2 messages

Feb 15, 2023, 11:00 PM motion setup

Buzzing Noise on X axis 7 messages

Feb 15, 2023, 5:05 PM motion

4028 running full speed at 0% 36 messages

Feb 13, 2023, 11:27 PM setup