fix-my-printer

After months of only showing one camera, today my Moonraker is showing the second camera instead 24 messages

Mar 15, 2023, 9:23 PM setup

CB1+M4P RatOS, how to install? 21 messages

Mar 15, 2023, 3:25 AM setup

MCU instant shutdown 14 messages

Mar 14, 2023, 3:59 PM other

mcu: Unable to connect 19 messages

Mar 14, 2023, 2:48 PM setup

printhead gone wrong 11 messages

Mar 14, 2023, 3:00 AM motion other

EBB36 "MCU 'toolboard' shutdown: Thermocouple reader fault" 16 messages

Mar 13, 2023, 9:04 PM other setup

DRV_STATUS: 00130050 2 messages

Mar 13, 2023, 1:35 PM other

Klipper Error after 2.0 update using old cfg from 1.1 12 messages

Mar 13, 2023, 9:12 AM setup

I'm getting weird errors when printing (Unknown command:"EXCLUDE_OBJECT_START") 6 messages

Mar 12, 2023, 8:50 PM other

Z Tilt always failing: Probed points range is increasing 2 messages

Mar 12, 2023, 3:19 PM motion setup

I can’t get two btt tmc5160’s to work on my manta m8p 20 messages

Mar 11, 2023, 4:16 PM motion setup

Overriding Nozzzle Prime Start in RatOS macro won't work 7 messages

Mar 11, 2023, 2:14 PM setup

Input shaper not work 6 messages

Mar 10, 2023, 6:25 PM setup

Klipper screen shows menu, but touch screen won't react after ratos2.0 update 4 messages

Mar 9, 2023, 11:17 PM setup

Ratos board selection 3 messages

Mar 9, 2023, 6:27 PM setup

Heater extruder not heating at expected rate 3 messages

Mar 9, 2023, 6:19 PM other

RatOS v2.0.0... now unable to join network "RatOS" 4 messages

Mar 9, 2023, 5:04 PM setup

octopus v1.1 bootloader 4 messages

Mar 9, 2023, 12:26 AM setup

Octopus 1.1 firworks 22 messages

Mar 7, 2023, 2:04 AM setup

Burning hotend - Rapido 8 messages

Mar 6, 2023, 7:18 PM other setup

How to update firmware on Octopus 429? 14 messages

Mar 5, 2023, 12:27 PM other

XY Stepper error 7 messages

Mar 5, 2023, 9:50 AM motion

XY axis scale wrong 2 messages

Mar 5, 2023, 12:36 AM motion

cant connect to klipper 8 messages

Mar 4, 2023, 7:51 PM other

Z_TILT_ADJUST - Impossible to complete. 34 messages

Mar 4, 2023, 6:20 PM motion setup

Rescue print after Power outage 6 messages

Mar 4, 2023, 5:30 PM other

Rapido UHF can 't reach more than 226 °C 3 messages

Mar 4, 2023, 11:19 AM other setup

G28 Home all behavior 6 messages

Mar 4, 2023, 4:34 AM setup

Rescue timelapse after Power failure 12 messages

Mar 3, 2023, 12:20 PM other

Extruder E-Steps Calibration 7 messages

Mar 2, 2023, 6:29 PM setup

Probe triggered prior to movement 68 messages

Mar 2, 2023, 1:21 PM motion setup

Belt path out of whack 56 messages

Mar 2, 2023, 8:45 AM motion

pin PC7 is an alias for z1_uart_pin 2 messages

Feb 28, 2023, 9:18 PM motion setup

TMC 2209 Driver Error 20 messages

Feb 28, 2023, 4:13 PM other

Heater disconnected from heating block 7 messages

Feb 27, 2023, 11:47 PM other

After Trying Move Home x-y got error message 11 messages

Feb 27, 2023, 8:52 PM motion setup

Right Motor idler assembly 28 messages

Feb 26, 2023, 3:07 AM motion

4028 PWM not working 10 messages

Feb 25, 2023, 11:22 AM other

Heating extruder not heating at expected rate 7 messages

Feb 24, 2023, 9:08 PM other

Part cooling not turning on when printing 3 messages

Feb 24, 2023, 8:02 PM other

V Core 3 CAN communication configuration 9 messages

Feb 24, 2023, 6:01 PM setup

Linear rail and Lead Screw lubrication 19 messages

Feb 24, 2023, 11:14 AM other

PETG melting between LGX and Mosquito Magnum 16 messages

Feb 23, 2023, 10:39 PM other

Belts rubbing against idler 8 messages

Feb 23, 2023, 10:28 PM motion

TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset) 5 messages

Feb 23, 2023, 3:45 AM motion other

Z-Tilt Fails 4 messages

Feb 23, 2023, 12:58 AM motion setup

my v minion is noise 4 messages

Feb 22, 2023, 8:40 PM motion

Klipper won't start. 4 messages

Feb 22, 2023, 8:28 PM setup

Belt move too low and goes over flange 20 messages

Feb 22, 2023, 2:27 PM motion

Tightening belts causes y-rail noise Vcore3 6 messages

Feb 22, 2023, 2:35 AM motion