fix-my-printer

ADXL345 Not Working 81 messages

Apr 25, 2023, 10:44 AM setup

Uneven belts tension and square xy 146 messages

Apr 24, 2023, 8:21 PM motion

Bed level issues for over 9 months now. 62 messages

Apr 24, 2023, 7:58 PM motion other setup

Z-offset seems to be wrong every time 22 messages

Apr 24, 2023, 1:24 AM motion setup

is it toothed idlers? 4 messages

Apr 23, 2023, 8:05 PM motion

Pin 'adxl345_cs_pin' is not a valid pin name on mcu 'mcu' 12 messages

Apr 23, 2023, 5:51 PM setup

Motor 8 Dead? 35 messages

Apr 23, 2023, 2:35 PM setup

MG995 Servo causing error and beeping 23 messages

Apr 23, 2023, 1:05 AM other

4028 is running the wrong way? 21 messages

Apr 22, 2023, 9:46 PM other

Tightening the lower belt makes the moving the x axis a lot harder 13 messages

Apr 22, 2023, 10:06 AM motion

Printer Shutdown TMC error? 5 messages

Apr 22, 2023, 9:51 AM other

Missing layers 5 messages

Apr 21, 2023, 5:28 PM other

Move out of range at start of print 29 messages

Apr 21, 2023, 9:14 AM motion other

unable to read tmc uart 'stepper_z' register ifcnt 36 messages

Apr 20, 2023, 2:50 PM setup

Wobbling movement on Y-axis 3 messages

Apr 20, 2023, 2:50 PM motion

All files in /config folder are Read-Only 3 messages

Apr 20, 2023, 12:42 PM other setup

Sensorless homing 8 messages

Apr 20, 2023, 12:51 AM motion

CB1 board and OV2659 Cam 4 messages

Apr 19, 2023, 9:41 PM setup

extruder motor gets too hot 2 messages

Apr 19, 2023, 2:24 AM other

Assembly, clicking left belt 2 messages

Apr 18, 2023, 7:20 PM motion setup

noisy printer, unable to locate sound source 6 messages

Apr 18, 2023, 5:41 PM motion

Horizontal pattern 2 messages

Apr 14, 2023, 5:39 PM other

Massive layer shifts 18 messages

Apr 14, 2023, 12:45 PM motion

Belt Replacement V-Core 3.1-500 3 messages

Apr 14, 2023, 10:36 AM motion other

The V core500's cable to the extruder hangs down . Any ideas? 8 messages

Apr 14, 2023, 3:36 AM other

Extruder heater not heating at expected rate 15 messages

Apr 13, 2023, 10:52 PM other

motor return error code 8 messages

Apr 12, 2023, 1:24 PM motion

end stop and probe shenanigans 29 messages

Apr 12, 2023, 1:15 PM setup

There's something I don't understand about the RATOS 4028 FAN guide. 7 messages

Apr 12, 2023, 9:35 AM setup

having all sorts of issues 17 messages

Apr 11, 2023, 5:24 AM other

V-Core 3 Rapido UHF + LGX Lite. Constant issues with filament not extruding/getting stuck in hotend. 19 messages

Apr 10, 2023, 4:38 PM other

4028 fan 99-100% big difference 13 messages

Apr 10, 2023, 12:14 PM other setup

Probe triggered or open all time 18 messages

Apr 10, 2023, 11:52 AM setup

Pi keeps dropping wifi and sometimes doesn't connect on boot 20 messages

Apr 9, 2023, 10:57 PM other

V minion Eva 3.0 sensorless homing problems 51 messages

Apr 9, 2023, 10:23 PM other setup

Part cooling fan running full speed at 0% and homing issues 8 messages

Apr 9, 2023, 4:09 PM motion other setup

z tilt issue 9 messages

Apr 9, 2023, 2:05 PM other setup

x endstop cable 4 messages

Apr 8, 2023, 10:35 PM other setup

Acceptable Amount of Bend of Leadscrew? 5 messages

Apr 7, 2023, 8:04 PM motion

Rapido plus hotend 11 messages

Apr 6, 2023, 10:13 PM other setup

Stepper Driver Port broken how to chang the Slot on Octopus F446 25 messages

Apr 6, 2023, 12:45 PM motion setup

Info on Connecting two Controller Fans, octopus 1.1 57 messages

Apr 5, 2023, 5:16 PM setup

Printer fails to probe a bed mesh when starting a print 10 messages

Apr 5, 2023, 8:37 AM motion

Z Offset 2 messages

Apr 4, 2023, 11:19 PM setup

4028 fan issue after updating to ratos2 23 messages

Apr 4, 2023, 6:35 PM setup

Vertical ridges on circular prints and vibration. 20 messages

Apr 4, 2023, 6:14 PM motion setup

Wobbly Z ? 5 messages

Apr 4, 2023, 5:02 AM motion

V-MiniON - Layer Shift on Y axis only 3 messages

Apr 2, 2023, 8:41 PM motion

Can't find Extruder rotation distance in Printer.cfg file. 3 messages

Apr 1, 2023, 3:03 PM setup

V-Minion Y Axis weird sound 7 messages

Apr 1, 2023, 2:30 PM motion