fix-my-printer

Broke my MCU Octopus v1.1 and am trying to get the replacement operating 11 messages

Jun 22, 2023, 10:02 PM setup

Move out of range on mesh 6 messages

Jun 21, 2023, 2:57 PM motion setup

Sudden bad extruder stepper 3 messages

Jun 20, 2023, 12:59 AM other

Heater extruder not heating at expected rate 20 messages

Jun 19, 2023, 10:38 AM setup

Printer running into negative values due to mesh calculation 16 messages

Jun 17, 2023, 9:22 PM motion

strange behaviour of my vcore 10 messages

Jun 17, 2023, 4:34 PM motion

Steppers refusing to work (first time) 13 messages

Jun 16, 2023, 10:58 PM motion setup

Part Cooling fan doing what it wants 47 messages

Jun 16, 2023, 2:14 PM other

Z-Offset still doesnt save 29 messages

Jun 16, 2023, 1:28 PM other

Unable to push filament (blockage)? 4 messages

Jun 16, 2023, 3:18 AM other

"mcu cannot connect" error for no reason 22 messages

Jun 16, 2023, 2:24 AM setup

Section 'ratos_homing' is not a valid config section 38 messages

Jun 15, 2023, 7:14 PM other

Extruder wiring issues 24 messages

Jun 15, 2023, 1:54 PM other

Z steppers are inverted ( only when moving manually, mesh probing Z homing is fine! 3 messages

Jun 13, 2023, 7:05 PM motion setup

vcore 3.1 failing to home 2 messages

Jun 13, 2023, 1:56 PM other

Vcore 3.1 Rear Z arm slides down under weight of bed 40 messages

Jun 13, 2023, 5:05 AM motion

Rat Rig Minion Fan issues 61 messages

Jun 12, 2023, 4:45 PM setup

adxl345 wiring and config settings 2 messages

Jun 11, 2023, 4:44 PM setup

v-minion z rod noise 14 messages

Jun 10, 2023, 11:49 PM motion

Keep getting MCU error with Goliath hotend attached. 10 messages

Jun 10, 2023, 11:57 AM other

Updated everything. Now none of my usbs work 7 messages

Jun 10, 2023, 8:27 AM other

Ran update, MCU no longer reachable 7 messages

Jun 7, 2023, 10:40 AM other

Mesh levelling stopping about halfway through G29 52 messages

Jun 6, 2023, 6:18 PM other

Strange Bed Level Test Result 4 messages

Jun 6, 2023, 10:46 AM motion

belt shifting 11 messages

Jun 6, 2023, 1:32 AM motion

Can't equalize belt tension 22 messages

Jun 5, 2023, 6:20 PM motion

Bed tilted after G34 3 messages

Jun 5, 2023, 4:37 PM motion setup

Extruder Heater not Heating at Expected Rate 2 messages

Jun 5, 2023, 8:52 AM other

Is my rail eating itself? 2 messages

Jun 3, 2023, 8:18 PM motion

Belt grabber/adjuster broke. Replaced the adjuster but I have a new noise now. 5 messages

Jun 3, 2023, 11:11 AM motion

Inconsistent first layer 14 messages

Jun 2, 2023, 5:33 PM other

Clogged Nozzel? 12 messages

Jun 2, 2023, 2:14 PM other

Y-Rails not tightening. 6 messages

Jun 2, 2023, 3:50 AM motion setup

Z Offset not saving 13 messages

Jun 1, 2023, 3:08 PM motion

Leadscrews ratrig 3.1 kit 500³ 5 messages

May 31, 2023, 12:45 PM motion other setup

Bed Mesh Issues 2 messages

May 29, 2023, 8:55 PM other

Part cooling fan always on at low speed 24 messages

May 29, 2023, 11:00 AM motion setup

SKR 2 dead? 3 messages

May 28, 2023, 5:46 PM other

Goliath Hotend may extrusion 2 messages

May 28, 2023, 12:34 PM setup

Toolboard looses communication when generating a shaper graph for Y axis 2 messages

May 27, 2023, 10:28 AM other

EBB42 Where Do I Begin? 59 messages

May 26, 2023, 7:43 PM setup

BTT Smart Filament Sensor Issue 5 messages

May 25, 2023, 6:06 PM motion setup

Cannot obtain IP address over Ethernet 2 messages

May 25, 2023, 8:23 AM other

Filament jam after/during filament change 4 messages

May 24, 2023, 10:48 AM other

Rendering Video failed 10 messages

May 24, 2023, 8:30 AM setup

Can someone pls check my printer.cfg 16 messages

May 23, 2023, 4:34 PM setup

V-Minion SKR Pico RPiZero2 went crazy after 1 day of printing 8 messages

May 23, 2023, 1:36 PM motion other setup

Inductive probe suddenly triggers at a mere ~2mm 20 messages

May 22, 2023, 8:04 PM motion

endstops doesn't react to switches 15 messages

May 22, 2023, 4:22 PM motion setup

Printer jittering and spitting out errors 6 messages

May 21, 2023, 7:30 PM motion setup