fix-my-printer

Random layer shifts 2 messages

Jun 28, 2023, 7:04 PM other

Rapido Thermistor Repair? 11 messages

Jun 28, 2023, 12:58 PM other

4 Pin Fan Config on Octopus Pro: bug or stupid user? 4 messages

Jun 27, 2023, 3:07 PM setup

Probe triggered prior to movement 17 messages

Jun 27, 2023, 2:44 PM motion

X Y slipping skipping or other 32 messages

Jun 27, 2023, 9:12 AM motion

Temperature fluctuates by 1.5 degrees. 4 messages

Jun 26, 2023, 8:04 PM motion other setup

Z-Axis Slams into Bed in START_PRINT Macro 3 messages

Jun 26, 2023, 4:36 PM motion setup

y motor help 2 messages

Jun 25, 2023, 3:04 AM motion

Octopus Pro and Neopixel 8 messages

Jun 23, 2023, 4:40 PM setup

Layer shifts at high speeds on VC3-400 35 messages

Jun 23, 2023, 3:48 PM motion

clog during print but filament extrudes normally 4 messages

Jun 23, 2023, 6:22 AM setup

Please load new filament and resume 8 messages

Jun 23, 2023, 12:48 AM other

Broke my MCU Octopus v1.1 and am trying to get the replacement operating 11 messages

Jun 22, 2023, 10:02 PM setup

Move out of range on mesh 6 messages

Jun 21, 2023, 2:57 PM motion setup

Sudden bad extruder stepper 3 messages

Jun 20, 2023, 12:59 AM other

Heater extruder not heating at expected rate 20 messages

Jun 19, 2023, 10:38 AM setup

Printer running into negative values due to mesh calculation 16 messages

Jun 17, 2023, 9:22 PM motion

strange behaviour of my vcore 10 messages

Jun 17, 2023, 4:34 PM motion

Steppers refusing to work (first time) 13 messages

Jun 16, 2023, 10:58 PM motion setup

Part Cooling fan doing what it wants 47 messages

Jun 16, 2023, 2:14 PM other

Z-Offset still doesnt save 29 messages

Jun 16, 2023, 1:28 PM other

Unable to push filament (blockage)? 4 messages

Jun 16, 2023, 3:18 AM other

"mcu cannot connect" error for no reason 22 messages

Jun 16, 2023, 2:24 AM setup

Section 'ratos_homing' is not a valid config section 38 messages

Jun 15, 2023, 7:14 PM other

Extruder wiring issues 24 messages

Jun 15, 2023, 1:54 PM other

Z steppers are inverted ( only when moving manually, mesh probing Z homing is fine! 3 messages

Jun 13, 2023, 7:05 PM motion setup

vcore 3.1 failing to home 2 messages

Jun 13, 2023, 1:56 PM other

Vcore 3.1 Rear Z arm slides down under weight of bed 40 messages

Jun 13, 2023, 5:05 AM motion

Rat Rig Minion Fan issues 61 messages

Jun 12, 2023, 4:45 PM setup

adxl345 wiring and config settings 2 messages

Jun 11, 2023, 4:44 PM setup

v-minion z rod noise 14 messages

Jun 10, 2023, 11:49 PM motion

Keep getting MCU error with Goliath hotend attached. 10 messages

Jun 10, 2023, 11:57 AM other

Updated everything. Now none of my usbs work 7 messages

Jun 10, 2023, 8:27 AM other

Ran update, MCU no longer reachable 7 messages

Jun 7, 2023, 10:40 AM other

Mesh levelling stopping about halfway through G29 52 messages

Jun 6, 2023, 6:18 PM other

Strange Bed Level Test Result 4 messages

Jun 6, 2023, 10:46 AM motion

belt shifting 11 messages

Jun 6, 2023, 1:32 AM motion

Can't equalize belt tension 22 messages

Jun 5, 2023, 6:20 PM motion

Bed tilted after G34 3 messages

Jun 5, 2023, 4:37 PM motion setup

Extruder Heater not Heating at Expected Rate 2 messages

Jun 5, 2023, 8:52 AM other

Is my rail eating itself? 2 messages

Jun 3, 2023, 8:18 PM motion

Belt grabber/adjuster broke. Replaced the adjuster but I have a new noise now. 5 messages

Jun 3, 2023, 11:11 AM motion

Inconsistent first layer 14 messages

Jun 2, 2023, 5:33 PM other

Clogged Nozzel? 12 messages

Jun 2, 2023, 2:14 PM other

Y-Rails not tightening. 6 messages

Jun 2, 2023, 3:50 AM motion setup

Z Offset not saving 13 messages

Jun 1, 2023, 3:08 PM motion

Leadscrews ratrig 3.1 kit 500³ 5 messages

May 31, 2023, 12:45 PM motion other setup

Bed Mesh Issues 2 messages

May 29, 2023, 8:55 PM other

Part cooling fan always on at low speed 24 messages

May 29, 2023, 11:00 AM motion setup

SKR 2 dead? 3 messages

May 28, 2023, 5:46 PM other