fix-my-printer

Fuse 11 messages

Aug 12, 2023, 7:07 PM other

mini blobs slicer fix 3 messages

Aug 11, 2023, 6:03 PM motion other setup

Idle 4028 part cooling fan 19 messages

Aug 11, 2023, 4:39 PM setup

Probe issue with BIQU Microprobe 9 messages

Aug 10, 2023, 5:24 PM other

Layer shifting 11 messages

Aug 10, 2023, 9:15 AM motion other

printer shuts down as soon as print starts 2 messages

Aug 9, 2023, 3:12 PM other

Bondtech LGX extruder binding 8 messages

Aug 8, 2023, 3:18 PM other

Octopus 1.1 - connection problem 9 messages

Aug 8, 2023, 9:07 AM other

After recent maintenance and upgrade, I am getting "move out of range" errors 2 messages

Aug 8, 2023, 12:59 AM motion other

Thermistor reads incorrectly after installing new hot end - Solved 6 messages

Aug 7, 2023, 8:36 PM other

Part cooling fan always on 34 messages

Aug 7, 2023, 6:24 PM setup

Poor bed adhesion 9 messages

Aug 7, 2023, 12:16 PM motion other

IS not working or what's causing the ringing? 31 messages

Aug 7, 2023, 10:38 AM other

Solved: P&F inductive probe always triggered 2 messages

Aug 7, 2023, 1:55 AM motion setup

Stepper Wiring Issue 20 messages

Aug 6, 2023, 4:25 AM motion setup

Frame Slightly off Square on Ratrig VCore 3.1 400 Enclosed 10 messages

Aug 5, 2023, 8:24 PM motion setup

Updated to my detriment 12 messages

Aug 4, 2023, 10:20 PM setup

timer too close 3 messages

Aug 4, 2023, 9:19 AM other

Hot extruder motor 2 messages

Aug 4, 2023, 5:51 AM setup

Not Having Any Luck Trying to Add a Filament Runout Sensor 8 messages

Aug 4, 2023, 3:40 AM setup

Stepper staying powered up 3 messages

Aug 3, 2023, 11:34 PM other

BTT filament sensor 46 messages

Aug 3, 2023, 7:04 AM motion setup

Solved: Bed temp set to 0c but increasing temp 20 messages

Aug 2, 2023, 10:25 PM setup

Wifi connection unstable 2 messages

Aug 2, 2023, 10:43 AM setup

Z Tilt error help 8 messages

Aug 1, 2023, 6:39 PM other

Cannot adjust Z tilt 3 messages

Aug 1, 2023, 3:39 PM motion

Heater heater_bed not heating at expected rate See the 'verify_heater' 13 messages

Jul 31, 2023, 9:15 PM setup

Part Cooling Fan - Logic Inverted 2 messages

Jul 31, 2023, 4:55 PM setup

issues pt1000 rapido 2 8 messages

Jul 31, 2023, 4:17 PM setup

4028 on Octopus, EBB42 installed : 4028 running 0 or 100% only 4 messages

Jul 31, 2023, 1:41 PM setup

X rail to front extrusion difference 4 messages

Jul 31, 2023, 12:31 PM setup

RatOs internetwifi has a password and i dont know the password 3 messages

Jul 31, 2023, 8:29 AM setup

Bed is not being supplied power 8 messages

Jul 30, 2023, 8:01 PM other

New vcore Estopping on Startup 4 messages

Jul 30, 2023, 12:44 PM other

Why is my 4028 fan pulsating? 4 messages

Jul 30, 2023, 11:42 AM other

V-Minion X Axis leveling 2 messages

Jul 30, 2023, 11:23 AM setup

Pi CAM does not work 10 messages

Jul 30, 2023, 8:21 AM other setup

not sure what changed 7 messages

Jul 30, 2023, 1:53 AM motion other setup

XY motor plates not fitting well 2 messages

Jul 29, 2023, 11:33 PM setup

shaper graphs not showing in folder 2 messages

Jul 28, 2023, 6:59 PM setup

Stepper motors noise when enabled without moving. 13 messages

Jul 28, 2023, 2:04 PM motion other

Can't get a first layer laid down 9 messages

Jul 27, 2023, 8:05 PM setup

z-offset issue 9 messages

Jul 27, 2023, 4:07 PM setup

Problems with Octopus Pro H723 V1.1 11 messages

Jul 26, 2023, 9:25 PM motion other setup

Heated Bed Edges? 36 messages

Jul 26, 2023, 4:14 PM other

MCU Update error 21 messages

Jul 26, 2023, 3:01 PM setup

EBB42 with some idle sensors/actuators 39 messages

Jul 24, 2023, 4:44 PM setup

Probe misses the bed and doesn't detect it during calibration, causing the nozzle to push very hard. 26 messages

Jul 24, 2023, 4:15 PM motion

Trouble to flash my octopus v1.1 f446 on DFU mode. detected but not responding 10 messages

Jul 24, 2023, 2:35 PM setup

Board detected but unresponsive 2 messages

Jul 23, 2023, 1:22 PM setup