fix-my-printer

4028 Fan not running below 50% on SKR Pro 1.2 2 messages

Sep 18, 2023, 8:21 AM setup

my extruder didnt work 46 messages

Sep 18, 2023, 6:55 AM setup

beacon no model loaded 9 messages

Sep 17, 2023, 7:00 PM setup

Z axis - too much squish? 2 messages

Sep 17, 2023, 1:10 PM setup

How to get rid of vibrations? 27 messages

Sep 16, 2023, 2:33 PM motion other setup

LDO ADXL345 install 2 messages

Sep 16, 2023, 1:08 PM setup

Skipping on high X/Y positions 16 messages

Sep 15, 2023, 6:10 PM motion

servo short error while using correct cable ends 20 messages

Sep 15, 2023, 4:07 PM motion

Diagonally out of bounds... 2 messages

Sep 15, 2023, 3:39 PM motion other

Y axis vibration. is it NORMAL? 11 messages

Sep 15, 2023, 1:45 PM motion other setup

4028 does not turn off at 0% even with enable_pin 2 messages

Sep 14, 2023, 7:37 PM setup

V-core3-Octopus 1.1 -Pi 3a+ Ratos 2.02 : stops printing randomly #solved 18 messages

Sep 14, 2023, 12:49 PM setup

Rapido hotend not going below 179 degrees 6 messages

Sep 13, 2023, 9:07 PM other

BIQU Microprobe 11 messages

Sep 12, 2023, 12:35 PM other setup

Delta 4 pin fan not working 5 messages

Sep 11, 2023, 11:59 PM setup

Stepper skipping noise during primeblob 5 messages

Sep 10, 2023, 7:21 PM other

MCU Shutdown Error occasionally when heightmap probing 29 messages

Sep 10, 2023, 3:47 AM other

Non-ratrig endstop help 8 messages

Sep 9, 2023, 9:50 PM setup

MCU Shutdown Error while heightmap 10 messages

Sep 8, 2023, 7:01 PM other

PT1000 thermistor EBB42 9 messages

Sep 8, 2023, 4:46 PM setup

Various homing related issues 24 messages

Sep 8, 2023, 2:58 PM motion setup

octopus 1.1 usb over serial canbus "Option 'serial' is not valid in section 'mcu' 2 messages

Sep 8, 2023, 9:14 AM setup

ADXL app. correlation 6 messages

Sep 6, 2023, 7:19 PM setup

v-minion - rattling noise 23 messages

Sep 6, 2023, 2:00 PM motion other

Ratos, Prusa Einsy MK3, homing moves right instead of left. 10 messages

Sep 5, 2023, 2:20 PM motion

connecting 4 pin controller fan 4 messages

Sep 5, 2023, 7:22 AM setup

[Solved] Printer stopping after priming, hotend temperature fluctuates 3 messages

Sep 5, 2023, 4:48 AM other

[Closed - Upgrade 3.0 to 3.1] Lead screw too short by 20mm 3 messages

Sep 3, 2023, 8:14 PM motion setup

" Endstop z still triggered after retract " 8 messages

Sep 2, 2023, 12:42 PM setup

Manta m8p 1.1 + CM4 3 messages

Sep 1, 2023, 5:10 PM setup

Rat rig V-Core 3 Unable to connect to IP Address 26 messages

Sep 1, 2023, 2:29 PM setup

rapido uhf(old) Heater not heating properly 25 messages

Aug 30, 2023, 3:18 PM setup

Euclid probing issue (new install) 5 messages

Aug 30, 2023, 6:36 AM motion setup

Heatsoak with mosquito magnum on EVA 2.4 2 messages

Aug 30, 2023, 2:27 AM other

heating shuts if 1 second after prime line 2 messages

Aug 28, 2023, 8:01 PM other

Loud 5160 PRO 6 messages

Aug 26, 2023, 7:10 PM motion setup

Advice on fuse/plug 4 messages

Aug 26, 2023, 1:52 AM other

4028 FAN Not working 5 messages

Aug 23, 2023, 5:01 PM setup

Endstop crashes Octopus 1.1 / Raspberry pi 17 messages

Aug 23, 2023, 3:39 PM other setup

MCU LOST CONNECTION and now can't connect to rat os 2 messages

Aug 22, 2023, 12:04 PM setup

Over time build plate sinks in the rear 3 messages

Aug 20, 2023, 7:41 AM other

Heater issue: Heater extruder not heating at expected rate 14 messages

Aug 19, 2023, 11:14 AM other

Extruder heater continues heating past target temp 15 messages

Aug 18, 2023, 1:15 PM other

Mintemp error 4 messages

Aug 17, 2023, 7:31 AM motion other

Odd mechanic skipping/bouncing/hitting 15 messages

Aug 16, 2023, 8:39 PM motion

bed mesh out of range 7 messages

Aug 16, 2023, 8:29 AM setup

beacon 6 messages

Aug 14, 2023, 11:58 PM setup

Orbiter 2.0 extruding exactly 4x too much 5 messages

Aug 14, 2023, 6:00 PM setup

error 8 messages

Aug 14, 2023, 1:49 AM motion

Cleaning nozzle after filament run-out 15 messages

Aug 14, 2023, 12:34 AM other