fix-my-printer

Ratos, Prusa Einsy MK3, homing moves right instead of left. 10 messages

Sep 5, 2023, 2:20 PM motion

connecting 4 pin controller fan 4 messages

Sep 5, 2023, 7:22 AM setup

[Solved] Printer stopping after priming, hotend temperature fluctuates 3 messages

Sep 5, 2023, 4:48 AM other

[Closed - Upgrade 3.0 to 3.1] Lead screw too short by 20mm 3 messages

Sep 3, 2023, 8:14 PM motion setup

" Endstop z still triggered after retract " 8 messages

Sep 2, 2023, 12:42 PM setup

Manta m8p 1.1 + CM4 3 messages

Sep 1, 2023, 5:10 PM setup

Rat rig V-Core 3 Unable to connect to IP Address 26 messages

Sep 1, 2023, 2:29 PM setup

rapido uhf(old) Heater not heating properly 25 messages

Aug 30, 2023, 3:18 PM setup

Euclid probing issue (new install) 5 messages

Aug 30, 2023, 6:36 AM motion setup

Heatsoak with mosquito magnum on EVA 2.4 2 messages

Aug 30, 2023, 2:27 AM other

heating shuts if 1 second after prime line 2 messages

Aug 28, 2023, 8:01 PM other

Loud 5160 PRO 6 messages

Aug 26, 2023, 7:10 PM motion setup

Advice on fuse/plug 4 messages

Aug 26, 2023, 1:52 AM other

4028 FAN Not working 5 messages

Aug 23, 2023, 5:01 PM setup

Endstop crashes Octopus 1.1 / Raspberry pi 17 messages

Aug 23, 2023, 3:39 PM other setup

MCU LOST CONNECTION and now can't connect to rat os 2 messages

Aug 22, 2023, 12:04 PM setup

Over time build plate sinks in the rear 3 messages

Aug 20, 2023, 7:41 AM other

Heater issue: Heater extruder not heating at expected rate 14 messages

Aug 19, 2023, 11:14 AM other

Extruder heater continues heating past target temp 15 messages

Aug 18, 2023, 1:15 PM other

Mintemp error 4 messages

Aug 17, 2023, 7:31 AM motion other

Odd mechanic skipping/bouncing/hitting 15 messages

Aug 16, 2023, 8:39 PM motion

bed mesh out of range 7 messages

Aug 16, 2023, 8:29 AM setup

beacon 6 messages

Aug 14, 2023, 11:58 PM setup

Orbiter 2.0 extruding exactly 4x too much 5 messages

Aug 14, 2023, 6:00 PM setup

error 8 messages

Aug 14, 2023, 1:49 AM motion

Cleaning nozzle after filament run-out 15 messages

Aug 14, 2023, 12:34 AM other

Fuse 11 messages

Aug 12, 2023, 7:07 PM other

mini blobs slicer fix 3 messages

Aug 11, 2023, 6:03 PM motion other setup

Idle 4028 part cooling fan 19 messages

Aug 11, 2023, 4:39 PM setup

Probe issue with BIQU Microprobe 9 messages

Aug 10, 2023, 5:24 PM other

Layer shifting 11 messages

Aug 10, 2023, 9:15 AM motion other

printer shuts down as soon as print starts 2 messages

Aug 9, 2023, 3:12 PM other

Bondtech LGX extruder binding 8 messages

Aug 8, 2023, 3:18 PM other

Octopus 1.1 - connection problem 9 messages

Aug 8, 2023, 9:07 AM other

After recent maintenance and upgrade, I am getting "move out of range" errors 2 messages

Aug 8, 2023, 12:59 AM motion other

Thermistor reads incorrectly after installing new hot end - Solved 6 messages

Aug 7, 2023, 8:36 PM other

Part cooling fan always on 34 messages

Aug 7, 2023, 6:24 PM setup

Poor bed adhesion 9 messages

Aug 7, 2023, 12:16 PM motion other

IS not working or what's causing the ringing? 31 messages

Aug 7, 2023, 10:38 AM other

Solved: P&F inductive probe always triggered 2 messages

Aug 7, 2023, 1:55 AM motion setup

Stepper Wiring Issue 20 messages

Aug 6, 2023, 4:25 AM motion setup

Frame Slightly off Square on Ratrig VCore 3.1 400 Enclosed 10 messages

Aug 5, 2023, 8:24 PM motion setup

Updated to my detriment 12 messages

Aug 4, 2023, 10:20 PM setup

timer too close 3 messages

Aug 4, 2023, 9:19 AM other

Hot extruder motor 2 messages

Aug 4, 2023, 5:51 AM setup

Not Having Any Luck Trying to Add a Filament Runout Sensor 8 messages

Aug 4, 2023, 3:40 AM setup

Stepper staying powered up 3 messages

Aug 3, 2023, 11:34 PM other

BTT filament sensor 46 messages

Aug 3, 2023, 7:04 AM motion setup

Solved: Bed temp set to 0c but increasing temp 20 messages

Aug 2, 2023, 10:25 PM setup

Wifi connection unstable 2 messages

Aug 2, 2023, 10:43 AM setup