fix-my-printer

vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts 101 messages

Jan 25, 2025, 2:01 PM motion other setup

how to change probe offset on v minion 8 messages

Jan 25, 2025, 1:01 PM Solved setup

unable to read tmc uart 'stepper_z' register ifcnt 13 messages

Jan 24, 2025, 7:48 PM setup

SOLVED VAOC Suggests misalignment, But tension and skew seem fine. What else could be wrong? 3 messages

Jan 24, 2025, 3:30 PM setup

Printing Speeds past 150. 20 messages

Jan 23, 2025, 7:23 PM motion

Stepper missing steps? 5 messages

Jan 23, 2025, 1:51 PM motion Solved

VC3.1 - SuperPinda - !! Retries aborting: Probed points range is increasing. -Z-Tilt Problem 5 messages

Jan 23, 2025, 1:31 PM motion other

Printing issues on new 500 IDEX 50 messages

Jan 23, 2025, 12:09 AM other setup

VC4 Part cooling fan will only run at 100% 41 messages

Jan 23, 2025, 12:03 AM other

Crash after running belt tension test 6 messages

Jan 22, 2025, 8:45 PM Solved setup

Access to configurator RatOS 32 messages

Jan 22, 2025, 3:24 PM setup

Part Cooling fan doesn't work 13 messages

Jan 22, 2025, 12:48 AM setup

Vcore 3.1 500, stops extruding mid print 4 messages

Jan 22, 2025, 12:05 AM other setup

IDEX 500 Orbiter V2 Smart Sensor issues. 40 messages

Jan 21, 2025, 10:27 PM other setup

Fix my racking 9 messages

Jan 21, 2025, 9:56 PM motion

No VAOC Camera Image 4 messages

Jan 21, 2025, 5:53 PM Solved setup

Orbitor filament sensor 198 messages

Jan 20, 2025, 6:42 PM other

Endstop dual_carriage still triggered after retract 13 messages

Jan 20, 2025, 5:55 PM motion Solved

Hotend change, what I need to change in klipper and slicer? (Clogging Problem) 16 messages

Jan 20, 2025, 1:34 PM Solved setup

Z Rear not moving 50 messages

Jan 20, 2025, 10:54 AM motion Solved setup

VCore 4 500 - "Died mid-print, got an ADC out of range now. Thermistor tests 1.074 kOhm 3 messages

Jan 19, 2025, 8:12 PM other

YeagerBomb VAOC issues 5 messages

Jan 19, 2025, 7:41 PM motion Solved

Adding an extra NIDEC Fan 31 messages

Jan 17, 2025, 2:19 AM Solved other

Homing sequence kill homing switch 8 messages

Jan 16, 2025, 12:42 PM motion

Negative temp readings from Octopus V1.1 F446 23 messages

Jan 15, 2025, 9:57 PM Solved setup

Nozzle Oozing at the threads 4 messages

Jan 15, 2025, 6:33 PM Solved other

Configurating Machine 125 messages

Jan 15, 2025, 3:51 PM setup

Pei sheet chipping and peeling vcore 4 500 12 messages

Jan 14, 2025, 8:36 PM other

Extruder temperature not right 6 messages

Jan 14, 2025, 10:52 AM other setup

Y linear rails offset or profile twisted 4 messages

Jan 14, 2025, 8:52 AM setup

Hotend temp and power osscilating even after pid tune 10 messages

Jan 12, 2025, 8:28 PM other

Kind soul able to examine my crowsnest.conf to help get my 2nd Camera working (2nd non-VAOC Camera) 3 messages

Jan 12, 2025, 5:09 PM other

Hotend temp reads 159 degrees at all time, phaetus rapido uhf 3 messages

Jan 12, 2025, 5:30 AM Solved setup

Bed not heating - heater_bed not heating 2 messages

Jan 11, 2025, 3:27 PM other

Clicking noise when moving gantry 10 messages

Jan 10, 2025, 5:41 PM motion

hi, I have sometimes this problem:TMC 'stepper_z 2 messages

Jan 10, 2025, 4:11 PM motion

Rapido 1 Reading Lower Than Expected Temperature 30 messages

Jan 10, 2025, 3:29 AM setup

Fan stopping when klipper shows 70% 13 messages

Jan 9, 2025, 9:57 AM other

VAOC Chicago Bolt Doesn't Fit 3 messages

Jan 8, 2025, 10:23 PM Solved setup

Klipper error after update 3 messages

Jan 8, 2025, 8:43 PM setup

---- 2 messages

Jan 8, 2025, 7:20 PM Solved setup

ADC out of range 4 messages

Jan 8, 2025, 7:02 PM motion other setup

Z_TILT_ADJUST_ORIG internal error after updates 3 messages

Jan 8, 2025, 1:23 PM Solved setup

VCORE 4 (HYBRID)forward and backward movement generate error 4 messages

Jan 8, 2025, 11:08 AM motion

Issues with VAOC on new V-core 4 500 IDEX 2 messages

Jan 8, 2025, 1:17 AM other setup

Lost communication with MCU 'toolboard_t0' 9 messages

Jan 7, 2025, 11:01 PM Solved other

'ratos_homing' not a valid section 14 messages

Jan 7, 2025, 9:32 PM Solved setup

V-Core 3.1 Belt-Tension 4 messages

Jan 7, 2025, 2:53 PM setup

Toolboard shutdown: "ADC out of range" after changing nozzle 82 messages

Jan 6, 2025, 7:23 PM Solved other setup

X-Y direction different sizes! 5 messages

Jan 6, 2025, 3:33 PM motion