fix-my-print

vcore 3.1 PACF woes 7 messages

Aug 17, 2024, 6:03 AM Extrusion

First layer issues after Ratrig Toolhead upgrade 27 messages

Aug 16, 2024, 6:35 PM Errors Extrusion

Filament breaks during bridging 6 messages

Aug 15, 2024, 7:28 PM Extrusion

V-Minion - Consistent perimeter print errors (Single wider layer + void) 25 messages

Aug 10, 2024, 3:59 PM Extrusion

1'st layer issue 4 messages

Aug 8, 2024, 5:35 PM Extrusion

MCU 'toolboard_t0' shutdown: ADC out of range 23 messages

Aug 8, 2024, 7:18 AM Errors

Strange Texture 5 messages

Aug 6, 2024, 11:07 PM Solved Extrusion

PA-15CF - Printer has been calibrated, yet I keep getting these imperfections. 5 messages

Aug 5, 2024, 9:47 PM Extrusion

Vcore 4 Bad first layer 32 messages

Aug 4, 2024, 9:03 PM Other Extrusion

First layer squeeze 3 messages

Aug 3, 2024, 1:03 PM Other

Can't dial in retraction 3 messages

Aug 3, 2024, 2:13 AM Extrusion

worbling on layer 2 (ASA) 14 messages

Aug 1, 2024, 5:02 AM Other Extrusion

My 3d printer stopped when my print was about to start and it didn’t cancel my print but the hotend 7 messages

Jul 27, 2024, 11:52 AM Other Errors

What does this look like? 4 messages

Jul 26, 2024, 8:49 PM Extrusion

Pillowing on very top surface 17 messages

Jul 21, 2024, 4:10 PM Extrusion

Underwhelming first layer after calibration 27 messages

Jul 19, 2024, 5:05 PM Extrusion

underextrusion during z-offset cal 3 messages

Jul 16, 2024, 2:00 AM Extrusion

PA tuning pattern fails 6 messages

Jul 15, 2024, 9:04 AM Extrusion

[VC4 400] Pattern on the wall 15 messages

Jul 9, 2024, 7:40 PM Extrusion

New VC4 prints awful 5 messages

Jul 9, 2024, 9:42 AM Solved Extrusion

flow issues at higher speeds 7 messages

Jul 7, 2024, 12:05 AM Solved Extrusion

Issue with ABS printing 5 messages

Jul 6, 2024, 3:27 PM Extrusion

UHF Oozing 2 messages

Jul 1, 2024, 12:26 PM Extrusion

Rough start... 80 messages

Jul 1, 2024, 10:46 AM Extrusion

Inconsistent extrusion 3 messages

Jun 26, 2024, 2:48 PM Solved Extrusion

Pressure advance tuning, infill weirdness 3 messages

Jun 21, 2024, 4:18 PM Errors

Struggling with PETG 5 messages

Jun 20, 2024, 4:38 AM Solved Extrusion

Reverse elephant foot 5 messages

Jun 18, 2024, 9:57 AM Other Extrusion

Horrible Top Layer and a groove? 4 messages

Jun 16, 2024, 10:57 PM Other Extrusion

Extrusion inconsistencies 4 messages

Jun 14, 2024, 11:50 AM Extrusion

extrusion issues 21 messages

Jun 14, 2024, 2:00 AM Extrusion

Vcore 4 endless ringing 77 messages

Jun 13, 2024, 6:28 AM Other Extrusion

Move exceeds maximum extrusion on filament change 6 messages

Jun 3, 2024, 1:49 PM Solved Errors

Primeline RatOS 2.1 11 messages

Jun 3, 2024, 1:57 AM Solved Other

SuperSlicer won't extrude first layer 29 messages

Jun 1, 2024, 5:51 PM Solved Extrusion

poor surface on ASA and ABS 12 messages

May 31, 2024, 1:40 AM Solved Extrusion

Printer stops due to overheating 7 messages

May 30, 2024, 10:16 AM Solved Errors

First Layer problems 3 messages

May 24, 2024, 2:55 PM Errors

Ring on my hand ring on my print 3 messages

May 21, 2024, 8:55 PM Other

support tuning for Bender 4 messages

May 21, 2024, 3:26 AM Other

Stringing Isue 4 messages

May 13, 2024, 2:06 PM Other Extrusion

Sagging ASA on overhangs 21 messages

May 11, 2024, 1:40 AM Solved Other

overextrusion in some areas 5 messages

May 10, 2024, 7:31 PM Extrusion

Filament is sticking to the internal Teflon tube of the Hotend 11 messages

May 7, 2024, 5:57 PM Solved Other Extrusion

Residue build up at nozzle 7 messages

May 7, 2024, 5:10 PM Solved Other Extrusion

underextrusion-like artifacts at small layer heights 2 messages

May 4, 2024, 11:42 AM Other Extrusion

Holes at Z-Seam with large nozzle 4 messages

May 2, 2024, 8:25 PM Solved Extrusion

flow or z move issues 2 messages

May 2, 2024, 7:32 PM Other Extrusion

what should I do… polymaker pla warping… noob here 5 messages

Apr 30, 2024, 6:44 AM Other Extrusion

Weird Artifacts / ripples due to Volumetric Flow Limit 3 messages

Apr 29, 2024, 5:56 PM Solved Other