ratos-support

Nevermore Filter 42 messages

Feb 2, 2025, 7:58 PM Configuration

Ran out of stack space trying to match the regular expression. 2 messages

Feb 2, 2025, 7:54 PM Macros Configuration Errors

Show printer Status via RGB Strip 9 messages

Feb 2, 2025, 5:03 PM Solved Info Customization

Anyone have a completely working Nginx Reverse Proxy config by chance? 5 messages

Feb 2, 2025, 4:19 PM Customization

option 'pin' is not valid in section 'heater_bed'. (V-Minion, running an SKRAT board) 17 messages

Feb 1, 2025, 9:44 PM Configuration

RatOS 2.1 on Voron V0 2 messages

Feb 1, 2025, 5:59 PM Customization

v-chonk: does not return to xy safe-home location before homing z 22 messages

Feb 1, 2025, 6:28 AM Macros Configuration Motion

MCU 'mcu' shutdown Timer too close error when running Belt Tension. 9 messages

Feb 1, 2025, 3:52 AM Solved Errors Configuration

rpi GPIO error 16 messages

Jan 31, 2025, 4:55 AM Solved Errors Configuration

Belt tension V4 300 Hype / Idex 2 messages

Jan 30, 2025, 9:46 PM Configuration Motion

Unable to parse 'inf' as a literal: malformed node or string: 10 messages

Jan 30, 2025, 1:24 AM Solved Errors

Stepper driver warning: OTPW flag set 2 messages

Jan 30, 2025, 12:24 AM Motion Other

Internal error on command:"G28" 70 messages

Jan 29, 2025, 12:12 PM Configuration Motion

Stepper Noise after Update to 2.1.0 RC2 21 messages

Jan 28, 2025, 9:51 PM Configuration Motion

Fans strange behavior. 22 messages

Jan 28, 2025, 3:57 PM Solved Configuration

// Unknown command:"G17" and "G3" when printing 19 messages

Jan 28, 2025, 3:06 PM Solved Configuration

SFS v2 triggering clog pause 2 messages

Jan 28, 2025, 2:07 PM Errors Configuration

beacon 3.1 wrong offset 5 messages

Jan 28, 2025, 10:04 AM Macros Configuration Motion Other

Rat Pack wont start 6 messages

Jan 28, 2025, 7:28 AM Solved Macros Configuration

Heater chamber_heater not supported 11 messages

Jan 28, 2025, 3:45 AM Solved Macros Configuration Errors

Unable to see Realtime Stream from Beacon 3 messages

Jan 28, 2025, 12:26 AM Errors

Print Start shows a warning about incomplete Slicer configuration. 49 messages

Jan 27, 2025, 10:32 PM Configuration

Probe Samples Exceed Tolerance 9 messages

Jan 27, 2025, 10:16 PM Errors Configuration

Error during accelerometer data streaming 23 messages

Jan 27, 2025, 5:21 PM Solved Errors Configuration

Printer Site Reference name 9 messages

Jan 27, 2025, 4:30 PM Macros

2.1 Installation stuck at ratos-configurator 7 messages

Jan 26, 2025, 4:56 PM Configuration

EBB42 flashing/setup via usb(data only) + 24v 9 messages

Jan 25, 2025, 11:33 PM Solved Configuration Boards

Default Filter Fans Speeds don't meet Ratrig Docs 87 messages

Jan 25, 2025, 11:03 PM Solved Errors Configuration

Pressure advance doesn't seem to get implemented 6 messages

Jan 25, 2025, 11:12 AM Configuration

Y-Stepper engages for X-Movement 22 messages

Jan 23, 2025, 1:13 PM Solved Customization

Pi Camera on New RatOS 4 messages

Jan 23, 2025, 9:22 AM Solved Configuration

"Must home Axis first" When trying to home after fresh 2.0.2 Install 104 messages

Jan 22, 2025, 1:37 PM Solved Errors

Rat rig VAOC 3DO Webcam not working in visual calibration 23 messages

Jan 22, 2025, 12:36 PM Macros Configuration

DC slammed on Homing after Set Kinetic Centre 9 messages

Jan 21, 2025, 9:44 PM Info Motion

MCU 'Toolboard t0' shutdown: Timer too close. 101 messages

Jan 21, 2025, 9:48 AM Solved Errors

Wrong skew profile tries to load 22 messages

Jan 21, 2025, 8:42 AM Solved Errors Configuration Motion

YeagerBomb RatOs not saving Z-offset 42 messages

Jan 20, 2025, 10:55 PM Configuration Motion

issues with vcore 4 500 PEI flex plate 3 messages

Jan 20, 2025, 8:55 PM Other

Pi has Problems to flash after reinstallation 22 messages

Jan 20, 2025, 6:10 PM Solved Errors Configuration

mcu 'beacon': Unable to connect 7 messages

Jan 19, 2025, 11:46 PM Solved Configuration

GuessWhatsThisParlor Error 31 messages

Jan 19, 2025, 11:28 PM Errors Configuration

NikoMan update issue 39 messages

Jan 19, 2025, 8:48 PM Solved Errors Configuration

toolhead variable_standby on print start T1 toolchange does not wait for T0 9 messages

Jan 19, 2025, 6:06 PM Errors Macros

Print Fail during beacon calibration after update - bug? 36 messages

Jan 19, 2025, 3:05 AM Errors

How do i fix this? 12 messages

Jan 18, 2025, 10:49 PM Solved Configuration

Warnings after updating and restarting 113 messages

Jan 18, 2025, 6:19 PM Errors Other

RatOS missing from Software Updates 4 messages

Jan 18, 2025, 4:51 PM Solved Configuration

RPICamv2 doesn't start as an VAOC cam. 25 messages

Jan 16, 2025, 5:00 PM Solved Configuration Customization

User Error 5 messages

Jan 16, 2025, 3:58 PM Solved Configuration Other

Notifications integration in RatOS >= v2.1 - telegram-bot, Pushover, MQTT? 6 messages

Jan 15, 2025, 11:22 PM Customization Other