ratos-support

Movement problem and config of the EZ board 18 messages

Feb 21, 2025, 11:50 PM Configuration Motion

BEACON_INITIAL_CALIBRATION - Z-Home Fail 3 messages

Feb 21, 2025, 8:48 PM Solved Configuration Motion

Hard recovery killed Klipper 7 messages

Feb 20, 2025, 11:50 PM Solved Errors

PT1000 problem 16 messages

Feb 20, 2025, 2:37 PM Other

Error evaluating 'gcode_macro PROBE_FOR_PRIMING:gcode': gcode.CommandError: No probe, beacon or blto 17 messages

Feb 20, 2025, 2:05 PM Customization

vaoc cant finde camera 58 messages

Feb 19, 2025, 4:16 PM Configuration

Prusa Einsy Configuration Issues 15 messages

Feb 19, 2025, 1:31 PM Errors Configuration Boards

VOAC calculating offset wrong by the same amount every time 63 messages

Feb 19, 2025, 1:32 AM Errors

Belt tension graph interpretation help 5 messages

Feb 18, 2025, 9:00 PM Solved Macros Motion

Orbiter 2.0 Current 6 messages

Feb 18, 2025, 8:33 PM Configuration

can´t flash Octopus V1.1 - Core-V4 500 IDEX 12 messages

Feb 18, 2025, 2:36 PM Errors Configuration Boards

Can not open RatOS in the browser 16 messages

Feb 18, 2025, 12:53 PM Configuration

Merc 1 Hydra RatOs 2.1 5 messages

Feb 18, 2025, 12:45 AM Macros Configuration Customization Motion

Chamber heater settings question 14 messages

Feb 17, 2025, 5:50 PM Solved Configuration

Both toolheads require Z-probe for IDEX? 8 messages

Feb 17, 2025, 2:24 PM Configuration Customization

Extra’s.resonance_tester ERROR 12 messages

Feb 16, 2025, 8:41 PM Solved Errors

ratos-configurator: invalid 24 messages

Feb 16, 2025, 4:10 PM Solved Errors

Hotend Fan Speed 11 messages

Feb 16, 2025, 3:58 PM Solved Configuration

Octopus Pro 446 and RatOS firmware not updating 7 messages

Feb 16, 2025, 12:05 AM Errors Boards

IFCNT driver error 2 messages

Feb 15, 2025, 6:40 PM Boards Errors Configuration Motion

Klipper shutdown due to webhook request(s) 7 messages

Feb 13, 2025, 11:01 PM Errors

E3D PZ Probe 4 messages

Feb 13, 2025, 7:24 PM Other

Realtime Analysis 9 messages

Feb 13, 2025, 7:01 PM Configuration

Realtime Analysis not working 8 messages

Feb 13, 2025, 6:43 PM Solved Errors

Idex error´s after update 9 messages

Feb 11, 2025, 8:09 PM Solved Errors Configuration

homing 13 messages

Feb 11, 2025, 3:47 PM Motion

Position after sensor less homing 156 messages

Feb 11, 2025, 10:36 AM Solved Configuration

i have an octopus pro 446 and it has some corrupt firmware on it 95 messages

Feb 10, 2025, 5:45 PM Solved Errors

adxl345 not working after initial flash 10 messages

Feb 10, 2025, 3:45 PM Configuration

After upgrade ratos z cannot home 4 messages

Feb 10, 2025, 1:25 PM Configuration

Configurate an unsupported Printer 5 messages

Feb 9, 2025, 3:40 PM Solved Configuration

ratos in mini pc 11 messages

Feb 8, 2025, 12:50 PM Customization

Filament unload lenght/speed change for dual filament path extruder setup 3 messages

Feb 8, 2025, 7:25 AM Solved Macros Configuration Customization

Ratos Invalid 31 messages

Feb 6, 2025, 3:22 PM Solved Errors

VAOC webcam stream not found 26 messages

Feb 6, 2025, 2:15 PM Solved Errors

RatOS eth0 issues. 16 messages

Feb 6, 2025, 2:04 PM Errors Configuration

pin PA15 used multiple times in config 5 messages

Feb 6, 2025, 1:50 PM Configuration Customization

Poor Adhesion On Edges 8 messages

Feb 6, 2025, 6:11 AM Other

"Must home axis first: 0.000 0.000 15.000 [0.000]" Error After Update to v2.0.2-36-g230929e3 9 messages

Feb 6, 2025, 3:04 AM Solved Configuration

mushrooming filament, unload variables have no effect 9 messages

Feb 6, 2025, 2:53 AM Macros Configuration

Turn off MCU Temperature Sensor Permanently 6 messages

Feb 5, 2025, 8:42 PM Solved Errors

Unable to set Enclosure heater temp after a print completes 102 messages

Feb 4, 2025, 8:54 PM Solved Other

Nothing working after latest update 7 messages

Feb 4, 2025, 8:19 PM Solved Errors

Flashing a 3rd (or a 4th or...) EBB42 8 messages

Feb 4, 2025, 8:16 PM Solved Configuration Boards Customization Motion

Dimensional accuracy 9 messages

Feb 4, 2025, 6:30 PM Errors

No match for TMC5160 v1.3 (not pro) in configurator. 4 messages

Feb 3, 2025, 8:39 PM Solved Configuration

Broken SD card boot loader. 6 messages

Feb 3, 2025, 8:15 PM Other

Move Out of Range Error 3 messages

Feb 3, 2025, 5:25 PM Errors

LGX Issues 8 messages

Feb 3, 2025, 4:00 AM Solved Configuration

Changing from 20 teeth motor pullies to 25 teeth pullies. Do I need to change anything in the config 4 messages

Feb 3, 2025, 1:42 AM Solved Configuration Customization Motion