klipper_kalico_help

"Unhandled exception during run" after installing CANbus 7 messages

Jan 13, 2024, 9:35 AM Error messages

can connect to printer via putty, but not via mainsail 2 messages

Jan 13, 2024, 8:11 AM Connectivity

bed mesh issue during print start 24 messages

Jan 13, 2024, 2:26 AM Solved Config Meshing & probing

0 uuids from operational setup 5 messages

Jan 12, 2024, 2:07 AM Connectivity

Extruder thermistor way off 99 messages

Jan 11, 2024, 10:13 PM Solved Config

problems with flashing STM32_Mini12864 board 2 messages

Jan 11, 2024, 6:42 PM Flashing

Issues with saving a configuration 10 messages

Jan 11, 2024, 5:30 PM Meshing & probing

Btt MMB i2c connection issues 3 messages

Jan 11, 2024, 5:03 PM Connectivity Error messages Config

EBBCAN 29 messages

Jan 11, 2024, 11:32 AM Error messages

Pre heating with TAP 5 messages

Jan 11, 2024, 1:29 AM Macros Config

ADC out of range 19 messages

Jan 10, 2024, 1:04 PM Error messages

Z_Calibrate offset not working 9 messages

Jan 10, 2024, 7:18 AM Macros

installed timelapse config and macro now im getting this error and in not sure what to do 117 messages

Jan 9, 2024, 8:48 AM Error messages Config

WiFi/flashing problrms SOLVED 53 messages

Jan 8, 2024, 10:06 PM Installation Flashing

Another Unable to read tmc uart but different 9 messages

Jan 8, 2024, 5:03 PM Error messages

Trouble getting two cameras to work at the same time 4 messages

Jan 8, 2024, 4:54 PM Camera

MCU Protocol Error .... again (solved) 3 messages

Jan 8, 2024, 11:30 AM Flashing

Klipper slow to startup (mcu not being recognized in log) 2 messages

Jan 7, 2024, 11:56 PM Solved

Is this a pressure advance problem? 3 messages

Jan 7, 2024, 11:26 PM Solved Config

Unknown command:"M73" 2 messages

Jan 7, 2024, 10:35 PM Error messages

SKR 3 v2.0 Board Not Appearing in /dev/serial/by-id List After Firmware Update 19 messages

Jan 7, 2024, 11:07 AM Installation Connectivity Flashing

MCU shutdown: timer too close 2 messages

Jan 6, 2024, 5:07 PM Error messages

Variable Heat-Soak 11 messages

Jan 5, 2024, 8:27 PM Macros

(Solved!) "activate_gcode:" commands in [probe] are ignored 15 messages

Jan 5, 2024, 8:56 AM Config Meshing & probing

Issue with input shaper crash? 7 messages

Jan 5, 2024, 3:07 AM Error messages Solved

Bed & Filter Fans turn off after first layer 11 messages

Jan 5, 2024, 1:36 AM Solved Macros

i installed klipperscreen and now i have this error what happened? 4 messages

Jan 4, 2024, 3:52 PM Installation Klipperscreen Config

Waveshare 2.8 DSI - (EE) no screens found(EE) 2 messages

Jan 3, 2024, 6:16 PM Klipperscreen

console command to edit printer.cfg 14 messages

Jan 3, 2024, 5:49 PM Macros

cannot connect to devices after pi packages update 12 messages

Jan 2, 2024, 4:49 PM Clicked update bttn

Need help running KlipperScreen VNC 2 messages

Jan 2, 2024, 4:46 AM Klipperscreen

PREHEAT Macro idle timeout 14 messages

Jan 2, 2024, 3:14 AM Macros

Better Print Start Macro leaves nozzle floating way above bed at print start. 28 messages

Jan 1, 2024, 10:44 PM Solved Macros Config

unable to get klipper screen to show anything. backlight on screen on. blank screen 2 messages

Jan 1, 2024, 8:02 PM Klipperscreen

printer.cfg recovery 17 messages

Jan 1, 2024, 3:18 PM Config

new webcam install 2 messages

Jan 1, 2024, 4:44 AM Installation

anyone else just update their raspberry pi and klipper won't work anymore? 2 messages

Jan 1, 2024, 1:25 AM Clicked update bttn

klipper led effects homing 2 messages

Dec 31, 2023, 2:41 PM Config

jumping off point. getting ready to enter the mix 56 messages

Dec 31, 2023, 12:45 PM Installation Flashing

Inconsistent Heating Error 3 messages

Dec 30, 2023, 5:56 PM Error messages

Klipper Novice - "MCU 'mcu' shutdown: ADC out of range" 12 messages

Dec 30, 2023, 11:38 AM Installation Connectivity Config

Can Network goes down on Firmware Restart. 69 messages

Dec 30, 2023, 5:21 AM Solved

underextrusion on Corners 2 messages

Dec 30, 2023, 5:15 AM Config

FYSETC Spider 2.3 "mcu" issue. Can't find serial. 3 messages

Dec 30, 2023, 1:14 AM Flashing

Spoolman not working 64 messages

Dec 29, 2023, 9:33 PM Config

Need help setting up tmc5160 drivers 17 messages

Dec 29, 2023, 4:15 PM Config

ADC out of range klipper mcu shutdown 8 messages

Dec 29, 2023, 1:48 PM Connectivity Error messages Config

Connect ADXL345 to BTT PI V1.2 but not the dedicated port 2 messages

Dec 27, 2023, 9:16 AM Meshing & probing

Thermocouple reader fault & Fluctuating temps at idle 3 messages

Dec 26, 2023, 9:51 AM Error messages

LDO Picobilical ‘Reset’ Issue 25 messages

Dec 24, 2023, 9:47 PM Connectivity Config Flashing