klipper_kalico_help

very first klipper install. I don't understand what wrong 3 messages

Jan 27, 2024, 1:57 AM Error messages Solved

Curropt install 5 messages

Jan 27, 2024, 1:41 AM Installation Error messages

MCU unable to connect after updating printer.cfg 11 messages

Jan 27, 2024, 12:23 AM Connectivity Error messages Solved

BTT SFS v2 Encoder Runout during PRINT_START 16 messages

Jan 26, 2024, 8:49 PM Macros Config

Updating MCU after Klipper Update 90 messages

Jan 26, 2024, 5:22 PM Solved Clicked update bttn Config Flashing

Fysetc voron V0.2 pro R1 kit catalyst reflashing/CM68 reimage(debian 11) 5 messages

Jan 26, 2024, 11:49 AM Flashing

Noob mistake Update w/o reading 21 messages

Jan 26, 2024, 3:41 AM Clicked update bttn

mcu: unable to connect 115 messages

Jan 26, 2024, 12:31 AM Connectivity

btt cb1 KAMP 4 messages

Jan 25, 2024, 11:01 PM Installation Solved Config Flashing

BTT PI V1.2 refuses to boot 40 messages

Jan 25, 2024, 9:14 PM Flashing

KAMP giving error Error evaluating 'gcode_macro BED_MESH_CALIBRATE:gcode': jinja2.exceptions.Undefin 3 messages

Jan 25, 2024, 8:32 PM Solved Meshing & probing

Shutdown due to webooks request 16 messages

Jan 25, 2024, 4:10 PM Error messages

Z axis retracting the wrong direction. 12 messages

Jan 25, 2024, 11:11 AM Solved Meshing & probing

I'm not sure what I'm doing wrong with my Z_endstop_calibrate . 20 messages

Jan 24, 2024, 5:46 AM Solved Config Meshing & probing

Rebooted my printer now i got this randomly? What do i do... 2 messages

Jan 24, 2024, 2:49 AM Error messages

MCU Protocol Error 8 messages

Jan 23, 2024, 12:58 PM Flashing

heater extruder not heating at expected rate 19 messages

Jan 22, 2024, 11:06 PM Solved Error messages

Could use some help, borked config while changing to TAP 2 messages

Jan 22, 2024, 10:53 PM Config

Non-Blocking TEMPERATURE_WAIT? 6 messages

Jan 22, 2024, 1:56 PM Macros

klipper shutdown 8 messages

Jan 22, 2024, 7:52 AM Error messages

machine fine then not… 4 messages

Jan 22, 2024, 6:27 AM Installation Error messages Config Clicked update bttn Flashing

USB device showing on lsusb command, but not on ls /dev/serial/by-id/* 8 messages

Jan 21, 2024, 8:52 PM Installation Solved Camera

Extruder motor stuttering 4 messages

Jan 21, 2024, 12:21 PM Solved Config

Z Movement inconsistent on V0.1 Modified 31 messages

Jan 21, 2024, 7:29 AM Config

Error after executing the G28 Z command. SOLVED 10 messages

Jan 21, 2024, 4:21 AM Error messages

Okay now explain it to me like I'm 5 11 messages

Jan 21, 2024, 1:00 AM Error messages Solved Flashing

additional endstop that is not assigned to any axis 14 messages

Jan 20, 2024, 9:41 PM Config

Cant move in Z due to MCU error: Stepper too far in past SOLVED 60 messages

Jan 20, 2024, 5:59 PM Macros Config

jontek2s Start Print macro with "Must home axis first" error 15 messages

Jan 20, 2024, 3:00 PM Macros

Moonraker errors out 5 messages

Jan 20, 2024, 1:39 PM Connectivity Error messages Solved

Klipper Firmware Version dirty 6 messages

Jan 20, 2024, 11:07 AM Error messages Klipperscreen

Move nozzle up when cancelling a print 7 messages

Jan 19, 2024, 2:52 PM Macros

canbus and klipper expander 2 messages

Jan 19, 2024, 2:27 AM Connectivity Installation Flashing

Problem connecting to MCU after updating Klipper 6 messages

Jan 18, 2024, 11:13 PM Installation Error messages Config

Skew too small for correction? 5 messages

Jan 18, 2024, 10:12 PM Config

klipper macro tweaking 5 messages

Jan 17, 2024, 1:44 PM Macros

heat soak and tap 10 messages

Jan 17, 2024, 12:02 AM Solved Config Meshing & probing

Bed Meshing 5 messages

Jan 16, 2024, 2:38 PM Meshing & probing

mcu unable to connect 23 messages

Jan 16, 2024, 4:29 AM Connectivity Solved

Kill Pin 11 messages

Jan 16, 2024, 3:28 AM Installation Config Flashing

KAMP, Klicky, bed meshing 2 messages

Jan 16, 2024, 2:29 AM Meshing & probing

Stuck at stm32g0b1xx. What's next? 36 messages

Jan 15, 2024, 3:56 AM Connectivity Installation Flashing

One temperature_fan with multiple sensors? 2 messages

Jan 15, 2024, 3:20 AM Solved Config

Section 'tmc2240 extruder' is not a valid config section 4 messages

Jan 14, 2024, 7:18 PM Error messages Config

First time flashing M8P Manta + CB1, I made a mess, need help 5 messages

Jan 14, 2024, 7:06 PM Connectivity Flashing

Probe triggered prior to movement on print start 18 messages

Jan 14, 2024, 5:37 AM Config Meshing & probing

How can I set up faster streams in Klipper using Crowsnest? 5 messages

Jan 14, 2024, 1:02 AM Camera

Mcu unable to connect 11 messages

Jan 13, 2024, 10:49 PM Error messages Klipperscreen Flashing

Section 'z_calibration' is not a valid config section? 7 messages

Jan 13, 2024, 8:14 PM Error messages

TMC 'extruder' reports error: GSTAT: 00000004 uv_cp=1(Undervoltage!) 3 messages

Jan 13, 2024, 11:23 AM Error messages