klipper_kalico_help

[solved] attempting to flash voron display, but limited config options shown 11 messages

May 30, 2024, 9:59 PM Flashing

BedFans.cfg from Ellis breaking my Additional Heater 5 messages

May 28, 2024, 8:57 PM Macros

Klipperscreen splash screen not working 5 messages

May 28, 2024, 6:30 PM Klipperscreen

RBP&BTT Pico 4 messages

May 28, 2024, 4:26 PM Installation Connectivity Flashing

Basic question regarding QGL 4 messages

May 28, 2024, 2:23 PM Meshing & probing

Formbot Voron 2.4r2 Config (M8P V1.1, CB1, EBB RP2040 & TAP) 13 messages

May 28, 2024, 10:36 AM Error messages Config

Error Z offset : SAVE_CONFIG section 'stepper_z' option 'position_endstop' conflicts with included v 16 messages

May 28, 2024, 9:53 AM Error messages Config

IFCNT Error 31 messages

May 28, 2024, 12:53 AM Connectivity

mks robin nano v1.2 unable to connect to mcu 9 messages

May 28, 2024, 12:49 AM Flashing

crowsnest - C920 - Autofocus setting crashes the camera 3 messages

May 27, 2024, 10:03 PM Camera

!! Lost communication with MCU 'EBB' 2 messages

May 27, 2024, 4:35 PM Connectivity

klipper screen help 20 messages

May 27, 2024, 4:04 PM Connectivity Klipperscreen

Extrude below minimum temp error 6 messages

May 27, 2024, 12:12 AM Error messages

Extruder not hot enough/bedfans not a valid pin errors! 31 messages

May 26, 2024, 9:51 PM Solved Macros Error messages Config

Klipper Screen wont load the network interface 2 messages

May 25, 2024, 9:22 PM Connectivity Klipperscreen

Voron STM32_Mini12864 adapter gives error 40 messages

May 25, 2024, 6:53 PM Installation Solved

uuid cant be found 4 messages

May 25, 2024, 12:24 PM Connectivity

Show Cursor didn't work? 11 messages

May 24, 2024, 8:20 PM Klipperscreen

Understanding Input Shaper results 4 messages

May 24, 2024, 5:31 PM Config

trying to set up fans as heaters. 29 messages

May 24, 2024, 2:21 AM Error messages Macros Config

cant flash klipper to spider board 3 messages

May 23, 2024, 5:42 PM Installation Flashing

SOLVED updated klipper and sensorless homing stopped working. 4 messages

May 22, 2024, 10:07 PM Clicked update bttn

Unable to write tmc spi 'stepper_x' register DRV_CONF 6 messages

May 22, 2024, 7:02 PM Error messages

Cant get Katapult to work 9 messages

May 21, 2024, 5:17 PM Installation Flashing

"Timer too close" at same point in a gcode file 10 messages

May 21, 2024, 12:56 PM Error messages

Pin 'gpio0' is not a valid pin name on mcu 'mcu' LDO Nighthawk Install 2.4 3 messages

May 21, 2024, 5:35 AM Installation Error messages

Unknown sensor 'chamber' 11 messages

May 21, 2024, 1:11 AM Solved Config

x and y not properly homing with sensorless homing 4 messages

May 20, 2024, 3:30 PM Meshing & probing

klipper mcu EBBCan: unable to connect 50 messages

May 19, 2024, 11:48 PM Error messages

slow print after cancel/restart 4 messages

May 19, 2024, 8:49 PM Solved Macros Config

klipper web interface loads on phone but not on macbook 8 messages

May 18, 2024, 7:54 PM Connectivity

MCU unable to connect 18 messages

May 18, 2024, 6:33 PM Error messages Solved

Problem with G28 6 messages

May 17, 2024, 5:21 PM Config

LDO Nitehawk w/ neopixel 5 messages

May 17, 2024, 1:18 AM Config

"Move out of range" on print start (Z Axis -1.680) 2 messages

May 16, 2024, 5:12 PM Error messages

LED sleep 4 messages

May 16, 2024, 2:43 AM Config

Troubleshooting Z Axis Homing Issues 87 messages

May 16, 2024, 1:36 AM Installation

MCU 'mcu' shutdown: Timer too close when trying to print with ERCF 2 messages

May 15, 2024, 8:18 PM Error messages

MCU 'mcu' shutdown: Move queue overflow 2 messages

May 15, 2024, 5:57 PM Error messages

troodon mini, not quite solved but still done 17 messages

May 15, 2024, 7:58 AM Connectivity Klipperscreen

pin out 2 messages

May 15, 2024, 12:09 AM Config

Timer too close? 9 messages

May 13, 2024, 1:48 PM Error messages

auto Z not working after update 2 messages

May 13, 2024, 1:39 PM Clicked update bttn

Nitehawk Toolhead Mounting points. 2 messages

May 13, 2024, 7:02 AM Installation Solved

Log file showing wrong MCU 13 messages

May 12, 2024, 4:43 PM Config

Unknown command "temperature" 3 messages

May 12, 2024, 9:37 AM Error messages Config Meshing & probing

manta m8p wont flash new firmware 13 messages

May 12, 2024, 6:38 AM Installation Flashing

mcu shutdown 10 messages

May 12, 2024, 12:33 AM Installation Error messages Solved

Z Calibration with Klippain and KlickyProbe 5 messages

May 11, 2024, 10:34 PM Solved Config Meshing & probing

Need a help with printer.cfg 21 messages

May 10, 2024, 12:40 PM Config