klipper_kalico_help

Mcu 'mcu': Unable to connect Errno 5 18 messages

Apr 15, 2024, 5:11 PM Connectivity Error messages

Unable to read tmc uart 'stepper_x' register IFCNT 5 messages

Apr 14, 2024, 4:24 PM Error messages

Sensorless Homing with BTT TMC 5160 Plus fails due to driver_SGT 18 messages

Apr 13, 2024, 9:58 AM Solved Config

Klipper shutdown immediately after after gcode download 13 messages

Apr 12, 2024, 9:00 PM Error messages Config

Klipper firmware v0.12.0 update on Manta M8P v2.0 not working 24 messages

Apr 12, 2024, 3:50 PM Solved Flashing

Klipper reports: SHUTDOWN 11 messages

Apr 11, 2024, 6:38 PM Connectivity Error messages Config Flashing

Issues with bed_mesh 2 messages

Apr 10, 2024, 8:56 PM Solved Config

Printer not ready after SW conversion 29 messages

Apr 10, 2024, 5:58 AM Installation Error messages Connectivity Config Solved

Error after Klipper firmware update on SKR1.4 - mcu : Unable to open serial port... 72 messages

Apr 8, 2024, 8:33 PM Installation Flashing

ERCF+Blobifier == Lost communication with MCU 'mcu' 26 messages

Apr 7, 2024, 10:49 PM Connectivity Error messages

m190 R33 is not waiting 5 messages

Apr 7, 2024, 10:20 PM Macros

Config variable names changed from v0.10.x to v0.12.0? 5 messages

Apr 7, 2024, 8:37 PM Clicked update bttn

BTT SKR Pico randomly stops being seen by klipper 4 messages

Apr 6, 2024, 2:55 AM Connectivity Error messages

help to orbiter settings 19 messages

Apr 5, 2024, 8:41 PM Config

NPN Probe, Avoiding MK52 Bed Magnets 11 messages

Apr 5, 2024, 12:00 AM Config Meshing & probing

Beeper not generating different tones 2 messages

Apr 4, 2024, 4:44 PM Solved Config

How to override the "points" specified in the [quad_gantry_level] of my printer.cfg? 2 messages

Apr 4, 2024, 12:50 PM Solved Macros Meshing & probing

Error on ‘SET_VELOCITY_LIMIT ACCEL_TO_DECEL=’: unable to parse 2 messages

Apr 4, 2024, 9:25 AM Error messages Macros Config

Klippain ShakeNTune "--scv: invalid floating-point value: '--max_smoothing' " 13 messages

Apr 4, 2024, 12:09 AM Solved Macros Config

Intermittent failure to start printing or resuming after pause. Heats to hotend temp and sits 2 messages

Apr 2, 2024, 9:21 PM Macros

MCU randomly shutsdown 2 messages

Apr 2, 2024, 7:18 PM Error messages

mcu 'mcu': Unable to connect 17 messages

Apr 2, 2024, 1:32 PM Installation Connectivity Flashing

BTT board flashing get_status error 16 messages

Apr 2, 2024, 5:23 AM Flashing

NPN Sensor on EBB2209 RP2040 44 messages

Apr 2, 2024, 2:41 AM Config Meshing & probing

Printer Config Help! G Code 19 messages

Apr 1, 2024, 10:51 PM Config

BTT SFS v2 filament switch triggering all the time 17 messages

Apr 1, 2024, 9:34 PM Config

MCU 'mmu' shutdown: Timer too close 43 messages

Apr 1, 2024, 7:55 PM Error messages

BTT Octopus DFU Mode 3 messages

Mar 31, 2024, 10:35 PM Installation Flashing

Klipper reports: SHUTDOWN 2 messages

Mar 31, 2024, 10:57 AM Error messages

RPI suddenly can't connect to Octopus CAN 3 messages

Mar 30, 2024, 7:47 AM Connectivity

cb1+ manta m8p+ sb2209 not showing up in klipper 45 messages

Mar 29, 2024, 10:07 PM Installation Config Flashing

updating btt pi 2 messages

Mar 29, 2024, 3:38 PM Error messages Config Flashing

MCU 'umb' shutdown: Invalid oid type 46 messages

Mar 29, 2024, 5:40 AM Error messages

klipper touch screen issue 3 messages

Mar 29, 2024, 2:33 AM Klipperscreen

Printer is not ready 62 messages

Mar 28, 2024, 9:43 AM Installation

Fysetc Cheetah v2 unable to flash firmware.bin 3 messages

Mar 28, 2024, 1:03 AM Installation Flashing

MCU Protocol Error Fresh Install 63 messages

Mar 28, 2024, 12:56 AM Error messages Klipperscreen Flashing

movement out of range error. z is trying to go negative, through the bed. 2 messages

Mar 27, 2024, 10:55 PM Error messages

Problem with connecting to MCU after update 11 messages

Mar 27, 2024, 7:27 PM Flashing

Host disconnecting from MCUs 5 messages

Mar 27, 2024, 12:24 AM Error messages

timer too close (MCU) 7 messages

Mar 26, 2024, 5:59 PM Error messages

I can SSH into my Pi but not access mainsail 2 messages

Mar 26, 2024, 4:58 PM Installation

Wifi connection problems when Screen is connected to Pi. 2 messages

Mar 26, 2024, 7:47 AM Klipperscreen

setting up a home network. 17 messages

Mar 26, 2024, 3:21 AM Connectivity

MCU not flashing 6 messages

Mar 25, 2024, 8:12 PM Installation Clicked update bttn Flashing

Print end macro help 2 messages

Mar 25, 2024, 6:16 PM Macros

my bed mesh is 2mm over the bed, after upgrade 2 messages

Mar 25, 2024, 11:41 AM Meshing & probing

Raspberry pi camera module v3 problem 5 messages

Mar 25, 2024, 9:26 AM Camera

klipper wont connect to mcu (formbot 0.2 build) 5 messages

Mar 24, 2024, 8:59 PM Error messages Config

Countdown or progress bar on Klipper Host Screen...? 2 messages

Mar 24, 2024, 6:53 PM Klipperscreen