voron_2_help_forum_public

Toolhead PCB Breakout Board 5 messages

Jan 16, 2024, 5:35 PM Electronics & wiring

small dings in build plate? (closed) 10 messages

Jan 16, 2024, 2:12 AM Mechanical Kits/parts advice

CAN issues with octopus 1.1 + BTT SB2209 10 messages

Jan 16, 2024, 1:25 AM Electronics & wiring

z pulley printed parts misaligned? (closed) 2 messages

Jan 15, 2024, 10:01 PM Mechanical

Where is the STL for Z Chain mount nut? 2 messages

Jan 15, 2024, 9:24 PM Initial setup

fried octopus (solved) 27 messages

Jan 15, 2024, 8:19 PM Electronics & wiring

I want to upgrade my 2.4 with a stealthburner. Does the stealthburner require a new carriage? 3 messages

Jan 15, 2024, 7:05 PM Mechanical

klipper screen on android 4 messages

Jan 15, 2024, 2:54 PM Configuration

New Voron 2.4 Initial startup error 8 messages

Jan 15, 2024, 12:10 PM Initial setup

Parts are taller than expected 6 messages

Jan 15, 2024, 11:57 AM Configuration

X slips on belt when going to 0,0 87 messages

Jan 15, 2024, 3:12 AM Initial setup Solved

problems with PA Tuning 20 messages

Jan 15, 2024, 12:37 AM Tuning

What is best solution for X limit switch with ChaoticLabs CNC TAP v2 8 messages

Jan 14, 2024, 8:30 PM Tap

Parts recommendation 10 messages

Jan 14, 2024, 7:05 PM Kits/parts advice

Current Build Suggestions 7 messages

Jan 14, 2024, 2:41 AM Kits/parts advice

Upgraded to LDO Super Power HT LDO-42STH48-2804AH motors and I am not seeing any difference in speed 93 messages

Jan 13, 2024, 10:30 PM Mechanical

Klicky unable to dock after bed mesh 41 messages

Jan 13, 2024, 2:27 PM Bed mesh issue Solved Configuration

LDO kit wiring, does the 3-red/1-black 24 PSU->Controller board matter for the red wires? 4 messages

Jan 13, 2024, 1:04 PM Electronics & wiring

Gantry binding when x-beam is full rear 12 messages

Jan 13, 2024, 12:54 PM Mechanical

Grooves and weird noises since upgrade to Rev 2 11 messages

Jan 13, 2024, 10:03 AM Mechanical

improving quality for thin small print 9 messages

Jan 12, 2024, 10:33 PM Tuning Configuration

Stealthburner LEDs turn off at 3000+ accels 8 messages

Jan 12, 2024, 10:01 PM Electronics & wiring

benchy vertical line 2 messages

Jan 12, 2024, 9:53 PM First print Configuration

PA_CAl macro problem 4 messages

Jan 12, 2024, 5:43 PM Tuning

Homing Z with klicky 85 messages

Jan 12, 2024, 4:35 PM Mechanical Initial setup Solved Configuration

WEIRD lines 20 messages

Jan 12, 2024, 3:48 PM Configuration

#parts breaking xy joint right upper cracking 16 messages

Jan 12, 2024, 3:46 AM Mechanical Solved

Motor clunks, layer shifts ~2cm in x&y 5 messages

Jan 11, 2024, 9:08 PM Mechanical Solved

Octopus 1.1 power jumper 19 messages

Jan 11, 2024, 8:47 PM Kits/parts advice Initial setup Solved Electronics & wiring

Measuring Resonances Y issue 5 messages

Jan 11, 2024, 5:31 PM Tuning Mechanical

Revo voron upgrade 38 messages

Jan 11, 2024, 8:28 AM Mechanical

B drive clunks, layer shifts 7 messages

Jan 11, 2024, 8:27 AM Mechanical Solved

Raspberry can`t find octopus board 19 messages

Jan 11, 2024, 1:40 AM Electronics & wiring

omron inductive probe issues, no signal (Octopus board) 62 messages

Jan 11, 2024, 1:38 AM Electronics & wiring QGL Configuration

Backup Current killed 2 Control Boards 53 messages

Jan 10, 2024, 11:49 PM Electronics & wiring

QGL needing a retry 14 messages

Jan 10, 2024, 8:00 PM Tap Mechanical Solved QGL

Stepperonline motors 76 messages

Jan 10, 2024, 2:53 PM Kits/parts advice

QGL points range ascending 10 messages

Jan 10, 2024, 9:39 AM QGL

ORCA Slicer making weird artifacts vs Pursa Slicer. 19 messages

Jan 10, 2024, 4:56 AM Tuning

Bed heater can’t heat up plate and kills itself in despair 10 messages

Jan 9, 2024, 11:20 PM Electronics & wiring

input shaper 40 messages

Jan 9, 2024, 11:08 AM Mechanical Initial setup Electronics & wiring QGL

Unable to read tmc uart 'extruder' register IFCNT 2 messages

Jan 9, 2024, 7:57 AM Electronics & wiring Configuration

Klicky probe 6 messages

Jan 9, 2024, 2:40 AM Mechanical Configuration

Input Shaper 8 messages

Jan 9, 2024, 12:04 AM Tuning

extruder only going backward 2 messages

Jan 8, 2024, 5:41 AM Mechanical Electronics & wiring

firmware 35 messages

Jan 8, 2024, 5:19 AM Electronics & wiring

m4x6 screws not going into my 24v power supply 11 messages

Jan 8, 2024, 2:53 AM Kits/parts advice Electronics & wiring

Controler board 4 messages

Jan 8, 2024, 12:36 AM Kits/parts advice Electronics & wiring

high layer print failure 6 messages

Jan 7, 2024, 9:11 PM Tuning Mechanical Solved

Input shaping graphs 17 messages

Jan 7, 2024, 5:47 PM Tuning