voron_2_help_forum_public

2023 must have upgrades 81 messages

Nov 15, 2023, 1:17 AM Kits/parts advice

Co Print Chromaset + Voron Tap Compatability. 3 messages

Nov 15, 2023, 12:35 AM Kits/parts advice Tap

What parts should I get for my voron 2.4 that have min/maxed value? 91 messages

Nov 14, 2023, 10:43 PM Kits/parts advice

Voron 2.4 Layer Shifting 38 messages

Nov 14, 2023, 6:02 PM Tuning Mechanical Printer shutdown

rough surface on top layer 6 messages

Nov 14, 2023, 4:39 PM Tuning

Bed mesh problems 21 messages

Nov 14, 2023, 1:09 PM Bed mesh issue

Nozzle scrapping the bed v2.4r2 with euclid probe 11 messages

Nov 14, 2023, 10:16 AM Z Offset

"Unable to read tmc uart 'stepper_z3' register IFCNT" error 5 messages

Nov 14, 2023, 9:31 AM Printer shutdown Electronics & wiring

Resonance testing interpretation 9 messages

Nov 14, 2023, 7:42 AM Tuning Mechanical

CAN Cabling affecting temperature stability and max extruder power? 13 messages

Nov 13, 2023, 10:03 PM Tuning Electronics & wiring Configuration

Door Panel Hinges - Question 9 messages

Nov 13, 2023, 2:54 AM Mechanical Kits/parts advice Solved

Temperature limit active on 2 year old printer? 21 messages

Nov 13, 2023, 2:16 AM Printer shutdown

Stringing and Blobbing On Long curved surfaces 2 messages

Nov 13, 2023, 12:54 AM Tuning

C'mon mate whats this new x y noise? 8 messages

Nov 13, 2023, 12:21 AM Mechanical

X and Z End stops always triggered Chaoticlab TAP 10 messages

Nov 12, 2023, 11:59 PM Mechanical Electronics & wiring

Inconsistent first layer after bed mesh of 0.14 variance or less 11 messages

Nov 12, 2023, 9:52 PM First layer

BTT Smart Filament Sensor 2.0 @ Octopus 2 messages

Nov 12, 2023, 4:08 PM Solved Electronics & wiring Configuration

z endstop 9 messages

Nov 12, 2023, 12:49 PM Mechanical Initial setup Electronics & wiring

Canbus bits hitting Z chain 12 messages

Nov 12, 2023, 5:41 AM Electronics & wiring Configuration

First layer not sticking to build plate 23 messages

Nov 12, 2023, 4:39 AM First print First layer Solved

latch 12 messages

Nov 11, 2023, 8:19 PM Kits/parts advice

printing issue 19 messages

Nov 11, 2023, 12:38 PM Tuning Configuration

V2.4r2 Not Connecting Anymore 14 messages

Nov 11, 2023, 5:39 AM Electronics & wiring Configuration

- Klicky Pcb and SB2240 connection 6 messages

Nov 10, 2023, 8:35 PM Electronics & wiring

Strange repeat striping pattern 6 messages

Nov 10, 2023, 6:35 AM Tuning Mechanical Electronics & wiring

How to connect a beeper to octopus v1.1? 25 messages

Nov 9, 2023, 10:40 PM Electronics & wiring

Having issues with bad print quality 3 messages

Nov 9, 2023, 9:22 PM Tuning

Mechanical issue/print artefact I can't pin down 336 messages

Nov 9, 2023, 9:14 PM Mechanical

Voron 2.4r2 is printing but.. 46 messages

Nov 9, 2023, 5:57 PM Tuning Solved

unknown layer shift 10 messages

Nov 9, 2023, 2:25 PM Tuning Mechanical

Probing accuracy issue, specific to z axis 11 messages

Nov 9, 2023, 12:51 AM Mechanical Initial setup Solved Configuration

MCU shutdown on X or Y home 18 messages

Nov 8, 2023, 9:19 PM Initial setup

QGL keeps failing in same corner 87 messages

Nov 8, 2023, 8:52 PM QGL

#spider 3.0 on my 2.4 6 messages

Nov 8, 2023, 5:55 AM Initial setup Configuration

StallGuard Unstable 10 messages

Nov 8, 2023, 4:51 AM Tuning

Octopus v1.1 Will Not Flash Firmware 30 messages

Nov 8, 2023, 4:01 AM Initial setup Solved Electronics & wiring

octopus V1.1 wiring power. Formbot VS manual 13 messages

Nov 6, 2023, 10:52 PM Solved Electronics & wiring

camera and filiment sensor 33 messages

Nov 6, 2023, 10:47 PM Electronics & wiring Configuration

anyone know why it skips when moving? belts are tight 15 messages

Nov 6, 2023, 10:31 AM Mechanical Solved

Voron 2.4 first layer is not forming and the extruder struck while running 10 messages

Nov 6, 2023, 9:27 AM Mechanical First print First layer Solved

BTT octopus pro V1.01 3 messages

Nov 6, 2023, 1:44 AM Electronics & wiring

Extruder loseing steps i think. 5 messages

Nov 5, 2023, 6:38 PM First layer First print

Incontinuous values at QGL exceeding sample_tolerance 3 messages

Nov 5, 2023, 7:59 AM Initial setup

print not starting macro issue I believe 18 messages

Nov 5, 2023, 2:39 AM Tap First print Solved QGL

Z3 on MOTOR_5 port quit working 15 messages

Nov 5, 2023, 2:19 AM Solved Electronics & wiring

Bad graph on Y resonance 16 messages

Nov 4, 2023, 10:35 PM Mechanical

AC Inlet Switch burnt out 15 messages

Nov 4, 2023, 8:32 PM Solved Electronics & wiring

MCU losing connection U2C & SB2240 24 messages

Nov 4, 2023, 7:37 PM Solved Electronics & wiring Configuration

Benchy Detach 84 messages

Nov 4, 2023, 6:36 PM Configuration

Frame grounding 11 messages

Nov 4, 2023, 4:12 PM Solved Electronics & wiring