#๐โtech
1 messages ยท Page 1025 of 1
Okay look, i have both AIO_PUMP and W_PUMP+ connectors on my board, the AIO itself is connected to the former, and I'm debating if connecting fans to the later is safe
Fine ... you handle it. Since clearly my perfect instructions are wrong ๐
It's safe
Let me know when you get tired of getting CPU FAN POWER errors on boot ๐
The pump is designed to run at full speed my dude...
Yes that's why you use the aio header...
...or the wpump.
Which is meant for aios
And this won't happen on any pump header
It fucking will if you plug the fans into anything other than the CPU header like you just suggested.
@reef patrol AIO_PUMP on my board is 12W 1A, W_PUMP+ is 36W 3A
I won't plug AIO into the wpump or i will damage the pump
On older boards that port was called hi_amp
No you won't...
^
o.O
^
But plug it into either - It doesn't matter. Whatever makes you feel good.
It's still 12v
Just plug the dang fans into CPU.
So just plug the fans into W_PUMP+ since they draw 2x the power of the pump

...
The spinny bois go into the central processor boi header.
Pump will draw 12W so why waste the 36W on it and underpower two fans
Also what fans are these lol
Sub 4k rpm fans are ^
I have a 45w fan
O.O
Blowiematron beat fan
remind me to never shove my finger through those fans as a joke
I've done that with low RPM fans
still hurts
but with fans going at several thousand RPM...gonna break bones at least
Eh I have a couple fans here on my desk blowing air and when I have nothing better to do I put my finger there.. granted they're relatively low RPM
Obviously I don't shove all the way through just a light touch
Fam 45w of fan
good question
In a molex connector, obviously.
...
Anything labeled aio or pump for a 3 pin
I think you're trolling me
12V is 12V
I thought molex was entirely for converting to sata to power storage drives
Lol
In order of preference.
... AIO/Pump header (more juice for thirsty pumps)
... 3pin fan header (and set it to 100% instead of PWM)
... A molex adaptor.
UNLESS
a 3 pin header can't be pwm
It's a smart AIO that plugs into CPU header as the only cable.
You know what i will just plug them all to molex
Molex works
PWM - aka. "curves" ๐
75w is always enough for at least 1 fan
I am dumbing it down to avoid another headache.
I wouldn't be complaining if the advice were correct
It's best to plug it into a header in pwm mode because that way it won't mess with the pump
hm, ok, so for multiple cables, anything labelled labelled along the lines of "pump" gets priority for pump cable, and AIO fans get plugged into the CPU fan header?
if it's all unified into one connector, pump and fans, CPU header cable is the spot to plug it in?
A 3 pin you have to be careful about since it can't run in pwm mode it will always be in DC mode which is very bad for the pump
Yep
If you wanna do manual adjustments or are using mismatched fans use 1 fan in CPU and one in opt
God damn
Delta makes a 108W 120mm fan
๐ณ
Yea but it's ac
that fan must really blow, or suck as the situation warrants
11000 RPM
Gimme that
It's so sad, I really wanted one for my "passive" cooling setup
Or a 134mm fan. At 12500 RPM
...methinks a massive fucking fan at 11000 rpm isn't "passive"
Technically the CPU cooler is passive
Just like a real server
9900k at 130w 62c max
I removed the Delta because it was just too jank for even me
This $15 fan is more powerful than 10 a12x25s :P
What's noise
In sorry I'm deaf from having purchased one of these fans

Also that's not true any more
The p12 pstco is now equal and sometimes quieter at the same pressure and airflow
Also if you really want a a12x25 just get a gentle typhoon
As someone who has bought close to a 1000 PC fans over the years
Noctuas reliability is nuts
I have some running for like a decade
GTs are good fans but the quality and consistency is lacking compared to noctua
Yeah, I just want them to stay performant and quiet for a decade
According to TPU's review, the GT is equal in performance to the A12x25, but considerably louder
[citation needed]
Noctua's long awaited NF-A12x25 fan hits the market with a bang in more ways than one. With more features than I can count with my fingers, all of which have been used to optimize performance and acoustics, it is a fan that makes no excuses about the lack of RGB lighting as it puts up a great showing against the competition.
And where do they have the same performance?
Both push the same CFM through the rad at the same RPM
๐คจ the 5% difference in cfm is similar to the 5% difference in noise
Also the typhoon isn't dampened, throw some grommets on and it's still alot cheaper
Where do you see a 5% difference in CFM? I see 0.3 at the most
Also, 5 dBA isn't a 5% difference. It's a log scale, that's a lot more
Error margins and error margins
Either way it's rubbered vs not rubbered
Grommets are not $15
In fact you should be able to get a pair of gts and grommets for a single a12x25
Either way my recommendation is actually p12 pstco
Yup
Arctic aint sampling tho :/
And the non co version has a vibration mode at 700-800 rpm
no its not!!!! its built into the desktop as an option :')
Yes but the dbus menu stuff that powers it is all kinds of awful
is that not handled by the desktop? at least mostly?
I know Firefox cant use the global menu for some reason
You can go for GT, but Noctuas reputation alone kinda makes the extra cost worth, no?
and OFC the gnome apps
If the fan is damn near certain to just not die ever why not spend the extra?
Never actually seen a Noctua fan die. My oldest one is 7 years old, still going with no problems.
Iirc that fan has been in more PC builds than I am years old.
you can't let some brown and cream spinny boi die
they're too pog to die
I mean
c'mon
Imagine if you could get literally any other computer component in that color scheme
I would
so that the fans could match the system
or
or?
OR

paint your system to match your perfect fans
XNOR
paint your CPU IHS
:')
painted gpu?
NVIDIA demonstrates custom RTX 3080 graphics cards Customized NVIDIA RTX 3080 Founders Edition cards are not exactly a new topic. NVIDIA had already showcased its Cyberpunk 2077 themed model before as well as a card inspired by Overwatch. NVIDIA has now commissioned modders to create yet another custom cards based on RTX 3080 Founders Editon. [โฆ]
OOO
the little details matter with personalised custom builds
I just saw a comment asking if Linux command line commands are pessimistic
Cause most commands only give output if something goes wrong
Such smooth brain question
Do they want congratulations for using cd or what
dir
or mkdir
It is pretty simple
Does ot work
Complains means it doesn't
Not complaining means it probably did
alias cd = cd %1 && echo "Congratulations"
Nobody wants to hear about your successful Friday night exploits.
But if something goes wrong, everyone's listening
:')
@fickle ore already used up aida trial time so cant test it lol if there is something else to check memeory latency I can try it
and in regards to the linux command response, on windows you have visual feedback if you open a folder, it's fairly obvious what happend, on linux quite often I have to check if nothing happend or if the task is running etc.
sometimes doesnt matters, sometimes annoying as fuck
Thats what && and || are for
yeah no thanks I don't want to do even more work
and in regards to the linux command response, on windows you have visual feedback if you open a folder
What visual feedback?!
Also you can customise your shell prompt to show the latest return code it received
@crisp granite Dude, the A12x25 just looks kinda beautiful.
Idk why, but I like the normal colors.
if you open a folder in windows you can very easily see that you now have that folder open, so it's visual feedback?..
you mean file explorer?
well yeah what else
Cause no visual feedback here.... xd
There is
yeah, but the same thing happens on Linux
Thats how all file managers work...
Thank you, Captain Obvious
They can also see what the $? variable is
yeah sometimes I do forget linux can have a gui ngl
X11 and wayland are the two big ways you can do guis
dont care how many, I'm just annoyed by cli's and even on linux variants that have a gui you need ot use it
WSL has no home folders, I guess that makes sense cause its currently only CLI
Bois, wth is this?
That's the bitcoin network difficulty over 3 years.
That drop was as hard as the last entire year of gains in something like 3 weeks. Pog
most definitely
if they keep up the pressure, bitcoin mining on GPUs won't be nothing more than a joke
or last gen ASICs will actually be a semi decent value
๐คฃ
it already is
it's actually semi practical now?
Dafuq happened
windows updated
When windows comes drunk to the job
I don't think that's how it's meant to be xd
One would think ๐ค
yeah I don't know that it is
At least you have that
On my windows 11 build, I didn't have the clock or system tray unless task manager was open
Thats why its called being a unpaid alpha tester
Yeah xd
can we all laugh at nikita
took a couple of hours considering c# can go fuck itself, lol
Thats tarkov right?
yea
Game still ridden with hackers in labs?
The subreddit still acting as a gestapo banning any mention of hacking?
sounds like reddit in general to me
in case you want to know a funny
i carried a sherpa
on wipe day
on my gaming chair
great community
I hope they finally remove the bs found in raid shit. The fleamarket was my lifeblood
Also made the pvp much more rare, as everybody was just getting some shit and camping their exit untill they wont get runthrough status and not unable to sell shit
idk bro i kill 15 people a raid
Yea gl getting rid of hackers in a unity game
Without some serious effort done against that
external unity hacks are actually quite a brainfuck
or mono, whatever
in general itโs just a bit less effort and a lot less skill thatโs required to reverse the game
I've been playing EmuTarkov. It's fun
mine attempted delivery but i missed it ๐ฆ
im gonna grab it from the post office on the way to work tomorrow
You know that home dirs were a thing before x11 existed right?
Yes
Unity has no stops from players flying around or accessing other players inventories accross the map
Other live players that is
use lf or something, or get familiar with cd, ls, mv, cp and watver
# Verbosity and settings that you pretty much just always are going to want. alias \ cp="cp -iv" \ mv="mv -iv" \ rm="rm -vI"
some usefull aliases to have it ask for confirmation before deleting/moving/copying stuff.
Eh at least yours isn't 9-12 during weekdays lol
nice, mobo send back &gotten a new one, now coworkers pc works and bios is not showing -1C for temps 
looks like for once it was a hardware not software issues on the gigabyte board
hi everyone
does anyone knows how to edit videos and like make a green screen social overlay
like a social animation of instagram and twitter on a green screen
so that i can use filter to remove the background
while editing my video
can you show me an example
https://youtu.be/lYzVlugbZiU watch at 1:12
Trio FNCS is in a few weeks and I am playing with Vadeal and rezon ay. Do you think I am gonna win Trio FNCS in Season 6? If you enjoy the video be sure to like, comment & subscribe :)
use code "OVA-NOAHREYLI" in the Item Shop! ๐
It's time to WIN Trio FNCS... ๐
Follow my socials:
โบ Twitter: https://twitter.com/noahreyli
โบ Twitch: https://www.t...
thats no green screen that's just the social media image and the @ handle in a box that has transparency
yes idk if we can do background transparent but mostly these things come in green screen
can you make like almost same like that
i want it from so long but no one knows any shit
i use nvidia to record
oh
i want to add it later when i edit
ah
Usually in editors the effect is called chroma key
yes
can you make that animation for me
it isn't an animation
dk much about it
not the bl intro, the instagram social pop up at 1:12
oh okay, but i need the social pop up at first place for that lmao xd
Yea, no.
oh
thats purely in editing
Trio FNCS is in a few weeks and I am playing with Vadeal and rezon ay. Do you think I am gonna win Trio FNCS in Season 6? If you enjoy the video be sure to like, comment & subscribe :)
use code "OVA-NOAHREYLI" in the Item Shop! ๐
It's time to WIN Trio FNCS... ๐
Follow my socials:
โบ Twitter: https://twitter.com/noahreyli
โบ Twitch: https://www.t...
1:12
500+ AE Motion Graphics Starter Pack: http://bit.ly/2SL9Qdm - If you're into creating content, there is no doubt that the videos your produce end up on Facebook, Instagram, YouTube, etc. So in this After Effects tutorial, we're going to breakdown several social media branding package techniques to help boost engagement with motion graphics. Lea...
Social Media Animations Pack is a modern After Effects template that contains a fantastic collection of dynamic animations that you can use in your videos. They're so easy to use and each one comes with its own individual color controller. A great way to enhance the look and feel of your skits, parodies, music clips, unboxing, self-improvements,...
ffmpeg can do a lot of stuff but good luck figuring out the arcane incantations to do it
Maybe dont advice someone ffmpeg when they just need something to do chromakeying
Or not even that, that's really just a stupid simple animation can do that in after effects or similar super ez
OBS should be good for most simple applications.
Or you can launch up blender 
thanks @pale sigil
Yes make it fancy 3D too, remember to spend way too long doing fire and smoke simulation for it
bro i can't use after effects
Loke no longer white what has this place come to
can anyone just make it for me and send the video
I can launch up the old editor
only need 2 socials
No better time to learn ๐
if you can, thanks a lot man
I can do it for 20 bucks
i can't be on pc for some weeks
exams soon so parents = strict


Anyway...
i need a chair as im changing my life style
any suggestions other than herman miller
need good posture and long confort levels
that does not look like it will be comfortable for hours
exoskeleton
Getting some screws put into the spine is also quite costly
true
also take a walk every so often. hernias scare me
im a bit beyond that lol
my spine is already fucked and i need to make changes due to a birth thing
thats why i wanna change my life style
Hernia? or something else related?
As in the soft spongey material is breaking down rapidly?
ye
Oh shit. That is pretty serious.
Bone-on-bone movement is either unconfortable to extremely painfull
The cartilage doesnt repair ever, i think. Only surgical means can add the cushioning back 
hmmm, maybe. But since there is so much quackery in the industry im needing to see that M.D. licence
looks nice. mes bottom and back
you can do that anytime
surprising how many offices are getting rid of their fairly expensive stuff
๐ต My email: louis@fighttorepair.org
๐ต Poll: https://docs.google.com/document/d/1SiWraWV9PnhQlHYTo3owAAuA8vWr69qcxIFj4m3_PNQ/edit
๐ต Automotive Right to Repair won in MA in 2020 on the ballot. https://ballotpedia.org/Massachusetts_Question_1,_"Right_to_Repair_Law"_Vehicle_Data_Access_Requirement_Initiative_(2020)
๐ต Steve Wozniak's initial vid...
Bit late on this ik
But I really hope Steve joins
Doubt it though
Oof... can't find my Noctua brackets.
So... no NAS until Noctua hopefully sells me a new set.
Curse you @solar hinge and actually wanting that AIO XD
What bracket?
For what cooler?
The big boi D15.
Already poked Noctua.
They sell most brackets already
Oh... they're actually super cheap on third party. Fuck waiting.
Yep
You should also ask them where you lost my aio screws ๐ @reef patrol maybe they know
Lol
๐ญ
Bluetoot
h
Thats how UI works 
:O so much drives :O
*partitions

Lot of drives if you point to the same network drive 3 times.
They are the same IP address yeah
Those are network attached storage devices 
(a socket consists of the ip address and port number)
Anyway this is my setup:
Of course there is also boot partitions but they are really not worth mountig during normal use
hm, how do you get that nice tree
lsblk
Ubuntu with ugly font.... hmmmm ok
I dislike that font xd
its not even installed by default! :p
wow
i like it for its non aliassing
I just noticed my font was still on hack, I changed it to fira-code now which is nicer
a what patch?
Nerd fonts, its a thing that lets symbols and emotes work in terminal
and ligatures for code
o
*terminal does need ligature support in the first place
st does have the patch for it
my perferred terminal works just fine with them (yakuake)
in case you don't know about it, it's basically konsole but as a dropdown terminal.
gnome-terminal does its job well enough for me ๐
did you see the thing about ms terminal being super slow and a single programmer in a short amount of time made a waaaay faster terminal?
Having a dropdown terminal is useful imo, if I were to use gnome I would probably use guake (which I did back when I still used xfce)
Like increasing the baudrate?
An Elevated Command Prompt (friends from the #demoscene will get this one).
Thanks @zadjii at Microsoft for allowing shaders in the Windows Terminal (https://t.co/tQAI120wgD). Now, before your manager notices, add hot reloading, error reporting AND mipmaps for "shaderTexture"..? https://t.co/u1pUTq7HFe
189
836
gif doesnt load but its a full mountainscene in terminal
[2/2] This was in response to the outlandish parade of excuses that I heard when I stated that it was simple to make a terminal render at several thousand frames a second, even with Unicode and color support. Hopefully this rains as thoroughly as possible on that insane parade.
348
what did you get?

weird combo
but aight
lol
I hope the wooting pad will be good
will try the radar v2 when it comes out
if the v2 would not be a thing I would prob already main the v1
eh
the thor is not great
imo
lol

can't you customize the AC+?
the AC+ is pretty decent
the customized color one should be the white one
so a bit slower than the black one
for some reason they named the two versions the same name
even though they are a different fabric
Ye just got mine
I'm at work rn so I can't play with it yet
that mouse seems uncomfortably small... guessing for portability
also faux cf is just over done and feels tacky now
although, that does look like it is moulded
so probably real now that i say that
low resin % as well so pretty good stuff as well...
less mouse = less grip
It's too big for me :(
if it covered all the contact area and was still lightweight id get it but small at the cost of grip seems counter intuitive
It's for fingertip
In fact you can remove a significant portion of the sides and back and still have all the contact needed
i never got the idea of claw grip, palm grip op
Palm limits precision or range of movement
id argue that palm is more precise due to more points of contact
Fingertip/claw lacks control for me
It's more precise at the same dpi but significantly limits range of movement
as for range of movement, thats fair, claw is probably better but then youre moving your fingers not your arm
At the same range of movement (higher dpi) it's significantly lower precision
What if you move the entire arm aswell? 
Yea that's palm
i use a trackball. MX Ergo
More muscles >> less muscles
Fingertip usually uses that but doesn't require it
Great for work
Awful for games
@ashen spindle #๐ฎโgame decided not to load all of a sudden so
- unity
- horrible netcode
- battleye
yeah had to resend it too
If you censor any mention of bugs/exploits it becomes a heck of a lot easier to miss em
I mean the engine is not at fault for them making dumb code design 
small indie company reminds you it's in beta
small indie company with a net worth of 5 million gbp
I guess it being c# means it's easier to decompile
Code obfuscation exist, and compiler optimisation
but if you just follow the bog standard unity network tutorials it already prevents things to be like in tarkov, they just said fuck it and made it extra stupid 
Step 1: NEVER trust user data
users will find set your server on flame somehow. dont let them
had a stroke?
No, im always stoking ma.. 

granted you get kicked if the distance is over 100m
so.. just run a check first if the distance is less than that?
.. how
yes
none of the unity built in network functions and none of the network plugins I touched would even have that a default behavior unless you completely mess up on purpose
that's almost impressive
bsg code
bsg? big gamer sucks code?
Big sucking gaymers
ah
With palming you limit your range of motion on your wrist
And completely loose the option to microadjist with your fingers
At the weight of the zaunkรถnig mice you also don't need the extra grip surfaces
Don't know how well the sandblasted one sticks to your fingers though
you can still microadjust, its just more picoadjustment depending on how tightly you hold the mouse
Not really microadjustments then
id argue picoadjustments are harder on a claw tho
Not really
Depends how you setup the software
If you just regulate them with pushing against one side harder
You can do that with every grip
Not ideal
although the lightweight would mean less inertia so itd move easier with a smaller force
With fingertip you could just use your fingers and/or wrist to achieve the same
And would stop easier, overlooked point for some reason
it would stop with less force as well yes
although depending on your surface/feet it may stop due to friction anyway
so ideally a glass surface would be used, however the sensor might not like that
Meanwhile from zowie we get the tenth EC iteration 
Is a 3360, that doesn't give a fuck ehat surface you throw at it, it just tracks
tbh it really doesnt matter, i just find a palm grip more comfortable and less straining on the weaker muscles in fingers
Comes with high purity ptfe, dunno how high purity they actually are
It really is not straining
Since it barely weighs anything
specifying high purity is like saying this plastic is highly this plastic, that makes me more sus than just saying ptfe
Eh
Then use teflonโข๏ธ.
extra marketing jargon meant to appeal to those who cant think straight 
But the difference in feel between 99% and 99.9% is stupid
So it actually makes a difference
for those uneducated, teflon = ptfe
(for those reading later)
you always get diminishing returns at the high end
nah, ptfe is great. Glue really dislikes dealing with that non-stick polymer
I mean they used hyperglides before
But the new shape does not allow them to do that
They could just ask corepad to make them for their mice
just dont heat it to ~250C especially when you have pet birds
just use air jets to hover the mouse 
magnets!
Magnets could be pretty cool.
No pomegranates though 
Only problem is tracking and actually keeping the damned thing suspended.
The tech is defo there, however.
You just need to be fine with a 3 grand mousepad and a VERY cold mouse chamber.
We can levitate a lightbulb and power it with the same magnetic source. WE HAVE THE TECHNOLOGY SPONGEBOB
better pc
16gb ram
what do i need then
and its a 3 second render intro
do you use AE
i5 8th gen
2.8hz base speed
its running on 3.5hz without oc
anyone pls help me this one time
nvme ssd?
150gb ssd
can anyone render the template for me pls
with quicktime and transparency
oh you mean the finished video is laggy?
yes
I asked if it was nvme, not that if you have ssd
no
uhh that sounds like you have some settings wrong then as even on slow hardware the finished video should be fine, just takes longer to make it
idk what that is though as I dont use AE
and that too its a 3 second video
oops
Razer Blade 14 Review. The best gaming laptop for ultra portability. This is the first laptop I've seen that I think can compete against the upcoming M1X MacBooks.
Laptop Skin - https://dbrand.com/shop/special-edition/damascus
On Sale Here - https://amzn.to/3yr7dxR
This is better than the Asus Zephyrus G14 in almost every way.
If you want to ...
oo
Weird it takes that long to process.. 3 seconds you say...
either its some new age, ray traced scene or the settings are set weirdly. Most important thing is to use a codec that has hardware acceleration support. Gets that gpu pumpin frames like no tomorrow
it was this issue @reef tundra , the render is fine now because of @hearty lake 's help, thanks everyone
Just render out as a png sequence, max quality and compatibility and speed
a lost vega unit 
the forbidden vega -- spooky
binned 4750G
^
Is there a properly maintained list of games that cannot handle 1000 Hz polling rates somewhere?
Would it be much use when the bios can be the leading cause?
?
If your BIOS is the issue, that's on you
But it's well known that some games cannot handle 1000 Hz polling rate properly
The Division, and possibly 2, had issues for me
Gave weird stutters when playing. Add that to the potential list when you start it ๐
But how would you know it their machine being the problem and not the program. List would either end up with superstition or obvious list of common problems kinda what a wiki or pinned forum post does
Sounds like a thing for pc gaming wiki
any of yall built your own desk?
I just upgaded my shitty ikea desktop to a butcherblock
100% better
i did a long time ago. Used a cabinet, some plastic totes, and two different counter tops to have an L-Desk
now i have a shitty ikea desk.
but it's nice so shrug
i have monitor mounts
and the ikea desk was like 0.75" thick
and the mounts would shake
new countertop is 1.5" thick solid wood
no movemnt now
i wanted to do that for my desk when i was gonna build it
i was gonna have the two sides clip together for easy movement. It was gonna be a real fucking desk. Something you could stand on if need be.
i planned on putting a sort of rubber mat thing on top of it.
My laptop is at 44% capacity
I am at only 93 (
it was 94 yesterday) on 12 pro max 
o...
There we go
XD
I was responding to "wonder what linus would say about this"
And someone said "why"
This was my response
Poor madison, don't think she was expecting such restrictions
She's already been told off by linus :p
That's bad
@reef patrol
nothing, cal is just star stuck because social media manager hit social media button that does things
smh when youre only getting 400MB/s network transfers because of some weird issue you cant figure out
Should try that, my macbook seems to have very bad battery, with most intensive tasks able to kill it instantly.
Nono
its funny
Because LTT mentioned about how strict they are about staff
and what they can say outside of work
and i commented this and she accidentally liked it then unliked
its just kinda funny

Misclicks happen all the time
Also @ashen spindle lad ive had singers/actors fave tweets, i dont give a shit xD
Also, it's a way to like something without it being official
nono
It says 71% which does not seem to be the case
thats my point
they aren't allowed to
Linus pretty much makes staff walk on egg shells with their personal social media
๐ณ
ive always heard the opposite
with how the internet works it's probably best for both him/his company and the employees themselves
Anyone know why Icon doesnt like ~ but Exec is fine with it???! cause if I type ~/Applications instead of the full path then it wont find the icon :/
is game talk broken agian
no
nope just discord shit itself or my connection to it
if you believe it to be, yes
because "alternative facts" are a thing

Watch the full WAN Show: https://youtu.be/Nzx96dGtmws
โบGET MERCH: http://www.LTTStore.com/
โบSUPPORT US ON FLOATPLANE: https://www.floatplane.com/
AFFILIATES & REFERRALS
โบCheck out our podcast gear: https://kit.co/linustechtips/lmg-podcast-gear
โบAffiliates, Sponsors & Referrals: https://lmg....
exactly
you cant compete
but they let employees make money with side channels/twitch is massive freedom compared to most companys
Those contracts have limits though.
and usually come from shit places where the content they make is shit
aka amazon studios not allowing devs to do their own products basically and any amazon game is just trash
His example of "a kitchen staff" is pretty apt and self dooming.
He can't really prevent his writers from streaming games on Twitch. Whether he wants to or not - No crossover between the job and side-gig.
https://specifications.freedesktop.org/desktop-entry-spec/latest/ar01s07.html
That is just the rules set out by the standard
can put it into contract != can hold up by court/be valid
I can write any employee owes me their soul but it's not really holding up 
i mean
and I'd assume this is something most cases would see that as an overreach of limitations an employer can make
well yeah but that's true for about anything, as you said impressions to have retention and all matters too
And they can take him to court for doing it with the wrong reasons ๐
no
Contracts also have to proof it is real, reasonable to engage in and with significant enough things you get notaries to signoff and be eyewitnesses to the agreement
with notice you can use any non protected reason
They can still take him to court arguing he's trying to abuse the contract.
Saying he can fire anyone with notice is like saying anyone can rob a bank. Which is not untrue - But there are consequences ๐
wont go to trail though
lack of standing will bring it down
tbf I am not well versed in canadian emploiyment law 
linus is reasonable, he'd only consider firing if there was a seriously good reason for it
so maybe that is fucked up over there
it really nuts is in some cases, iirc
Oh definitely - Just shooting down his poor argument and reasoning ๐
let me pull up the laws regarding that
yeah
Canadian labour laws and protections are way baren than what linus has
yeah
yep
as long as there is good reason, you can be fired on the spot
not being able to fire someone with notice seems like a really really odd law
i dont know anywhere that is true
otherwise, pay in lieu or advance warning is needed
generally its a month per year of working
so you pay salary+benifts for that time
or give notice
I'm used to seeing 2-3 year packages from the banks
ยฏ_(ใ)_/ยฏ
salary, benefits, that kind of stuff
which you live off of "while actively seeking new employment"
it cuts off when you get hired elsewhere iirc
given seriously good reason, I could see someone wanting an employee terminated ASAP
immediate termination is different.
Here we get legal right to payment for sudden loss of work not due to gross negligence. Just like you need to pay the doctor even though you cancelled 3 hours before the appointment you are getting the money for the agreed upon hours
i said with notice
with notice means you get advanced notice or just paid for that time
pretty standard
In developed countries with sane legal systems it is, but you are not there
canada does have a sane legal system, just a bit different than the european standards
we don't allow people to buy shotguns in a walmart so long as they look like adults

and well, we have pretty protective laws of the individual
but you really never need to worry about any of that as long as you don't step out of line
i dont think that is different anywhere lol
(I know it's technically not the case in america, but getting guns there is horrifyingly easy)
not really at a store lol
(FFL, sign a document, walk away with new gun)
Usually the ones having to worry are the ones buying the guns in the first place.. they are statistically the most likely murder suspect
wait for a background check taht fails 4 times
4473 iirc
then gives you a 45min wait
get denied because some dude 100 miles away with the close name hit his wife 10 years ago
fill out 5 forms, mail them in
wait
repeat
give up
call your sentors office
finally get it cleared up 2 months later
then...you spend your 300 dollars on your cheapo hi-point and magdump into the air just outside the door of the gun shop to celebrate
that took you literal months to get
๐
300 hipoint?
oh, and the hi-point blows up in your hand before you finish the mag
you getting 3?
they aren't actually that inexpensive???
shockingly so for the low AF price
Well, I'm Germany an employer can also forbid you from opening a side gig on Twitch. There are limitations, of course...
Just buy from a private individual 
that's gonna change in texas soon lmao
of course it sounds ridiculous if you oversimplify enough
Triangles are the true overlords
Kalash 1k and you can only buy by the crate no questions and no police ๐ณ
nah, the arms dealers dont ask that much for kalash. Prices of 30 to 130 usd per rifle. Authenicity is becoming an issue though they are copying the thing
That indeed sounds 'laughably easy'
@prisma crag I mean... obtaining guns period really shouldn't be as easy as "Go obtain a permit from your sheriff and pass probably a very basic test for it."...
:L
But most of the rest of the world don't have a centuries long history of being incredibly irresponsible with guns
Right, that sounds good if everything is actually done perfectly.
But it's America.
And more importantly, what makes up the permits? What tests and safeguards are in place so fucko mcgee doesn't get one?
Is it just forms?
Psyche evals?
So there just isn't a safeguard.
And instead of that it's basically just tedium.
Lmfao
America is such a joke.

And what about sociopaths and the other high functioning types?
Yep.
America be a joke.
Yes, but as luck would have it, luck and I'm sure nothing else at all, America seems to have by far the most cases of that.
Weird.
It's almost as if the parts to create such a device are fairly common.

I wonder how that happened.
sigh
No.
You can't 3D print a fully working firearm and expect it to survive more than a few shots.
Bullet, nail and hammer is all you need
I'm talking about the MANY cases of people just starting with an upper or any pistol and making an SBR because uppers can literally be purchased on fuckin' craigslist over there. :L
Yes, yes you are.
You can't 3D print a barrel and upper and expect it to work beyond a few shots.
But given how common the components are it becomes trivially easy to just 3D print the rest of it.
Idk, maybe it wouldn't be such an issue if you couldn't buy uppers and barrels without really needing to think.
You'll never stop ghost guns, but uhh.
Maybe just don't be making it too easy?
Bullets are the hard part
Guns are basically autoloaders with some tube hammering some spot
Whats wrong with melting down guns?
We also have few COVID deaths here, I'd also call that a win. :L
Metal can be reused for something else
Yes, because we locked down immediately.
Unlike everywhere else.
Y'know, we saw a potential huge issue and worked on preventitive measures so it wouldn't be a problem later.
I can go to the Gold Coast whenever I like and not wear a mask, y'know?
People just live normally.
And whenever cases pop up we all isolate for a few weeks and they go away again.
Yes, because Sydney is a massive hotspot.
Ok?
Here's my Twitter if anyone cares https://twitter.com/BigBruh54177371?s=09
I'd rather a program to trace where I go to make sure I don't die from COVID over everyone having COVID. :L
We just use contact tracing so everyone can live normally.
And more importantly, we've been over the programs used.
All are open source and all of them just report signed locations.
No personal data, names, what have you.
It's only geographic location and a phone number.
All already available, and all only used to trace potential hotspots.
You say that, but which one of us is doing better?

Well that's funny.
38 thousand cases...?
And that's today.
Weirdly enough as well you only have 1.4 million people.
But O_O omg bro.
Bro, you have so many less people and more cases per capita than the entirety of Australia has ever had.
You have more deaths per capita then Australia has had cases at the all time peak.

Look, same website for Aus.
Someone know how to run doom on those nanomachines or is it still not added like i asked bill microsoft to do. constantly replying "get out of my house".. one day he will see the light
And like...
O_O
O_O
@prisma crag Idk dude, kids these days?
We kinda have the numbers for this.
https://youtu.be/dYt57iq_L0g
bigger number
support ad-free shitposting, get voice files: https://patreon.com/GetGianni
song used: Painkiller Battle out of Hell - Loony Park Ambient
http://GetGianni.com
And remember as well, we have 17 times the population that you do, yet miraculously we've somehow managed to almost completely curb it by locking down when the global pandemic is ongoing.
?
This is what this should look like, y'see?
But...
Worldometers. @prisma crag
Site has a dubious history, but it does list sources and verify them.
See, the thing about worldometers is that they usually take a day or two to verify all data and purge the false shit, so it's never immediately up to date, but the data is known to be fairly accurate.
Hey dude.
Dude.
They're the same. :L
@prisma crag Didn't you literally claim 'kids these days' when I spoke about contact tracing and lockdowns, but you just said that the US has a great database so you don't need to look at anything else?
Seems a little ironic.
Look at the data, dude.
We're doing the best of any country when the population is considered.
Sure you have a couple with no cases, but none of em have 21 million people.
It's not wrong, though.
The data is correct. :L
We did, Australia is doing the best of anywhere for the size.
Look, this is a global pandemic.
Everywhere is under it's influence, that's why we locked down international travel.
We have few cases, did you think we'd just open the doors to India or something and just let the death in?
and that bothers me, because we dropped the ball here in canuckistan
we're had overwhelmed hospitals a few times, not chronically like the US has, but still
it's bad
I blame the half assed lockdowns from Mr. Cunt-Canary Trudeau
ngl, he's a pretty face, but the head is completely empty and he's fucked up every crisis he's had to deal with
and he's prime minister

Our government reacted real hard and we're fine.
Idk how anyone else hasn't seen the picture and gone "Oh shit."
Like, look at this.
Flatten the curve? Shit wasn't a curve so much as a hairpin turn.
That is how you do shit properly.
that is outright impressive
Yep.
most of the time, you guys had a few hundred cases at most
props to you aussies for taking this shit seriously
Peaked at 7k and within 4 months they were all gone.
Since then we've had a few hundred at most.
Right now we're on high hundreds, but goddamn if we aren't locking down again.
we've had a solid 1.42 million cases up till the 8th of july in canada
out of a country of barely 40 million
And shit, Hawaii is getting more confirmed cases per day than our average max per day.
With almost 18 times less population.
What are you all talking about? The vaccines exist so it's over, duh.
๐
they work when they're in people's bodies

No no.
We have to wait for darwin to take his cut first.
they don't work in the trash because no one fucking lined up and took em
wrong kind of darwinism
this is the SOCIAL Darwinism, the kind that takes anyone at random just because a few dumbasses out there decide to be plague rats
I'd be fine if it just killed off the plague rats, because good riddance
I still call that darwinism. :P
the issue is that the plague rats can have the virus mutate in them, and we could be in danger from that
True, true.
so...regardless, we separate them, ensure they only mingle with their own retarded kind
kill each other off
not us, with...IQ above a brick
anyway
real question
would Royal Carribean's new policy for plague rats on their ships departing from florida fit under r/maliciouscompliance?
they can't explicitly prevent people from boarding, but they can throw so many barriers to get over and hoops to jump through just to board, and get a substantially worse experience to boot if a plague rat does
Pog work that Hawaii is doing there.
that number aughta be 90-95 percent
Good guy Hawaii, now the rest of the world needs to do it. :L
everyone who can take, should take
Yep.

I'm getting my shots sometime in the next few weeks.
ALL of the old people need it first.
if you have a legitimate medical concern that would prevent you, don't
otherwise, shut up, line up and roll up your sleeve
But otherwise, yep.
Bruh, I'm actually getting sick of waiting.
My new Legder Nano Xs and S should arrive today.
Crypto wallet and hardware multifactor in the same device? Fuck yes.
What in the fuck is this?
Someone who missed the pricing bubble
not how that works
Sure it is
no way postage on a GPU can be that much
you can charge whatever you want for postage
you can also charge whatever you want for handling
nope, you charge the price of postage, if you're a real asshole, full vomit calibre, you charge a bit extra
but postage is never more than a hundred for a GPU
maybe for normal postage
but when you get into next day shit, of course it is
esp if it's international
ยฏ_(ใ)_/ยฏ


