build-help

Filamatrix Spring in LDO Kit 15 messages

Jun 15, 2025, 12:28 AM Build Issue

LDO Kit - Calibration Print? 6 messages

Jun 13, 2025, 3:31 PM Other

Lane 3 Extruder Issue (Solved) 8 messages

Jun 13, 2025, 12:37 AM Tuning

Armored Turtle calibration 89 messages

Jun 12, 2025, 9:47 PM Initial Setup

Roll Problems 118 messages

Jun 11, 2025, 11:13 AM Build Issue

[SOLVED] Fuzz/ Strings on filament cut 3 messages

Jun 10, 2025, 5:16 PM Tuning

Using turtleneck without a filament changer system 7 messages

Jun 10, 2025, 11:58 AM Other

Massive poops 25 messages

Jun 10, 2025, 1:03 AM Tuning

Increase Torque of Respooler Motors? 15 messages

Jun 8, 2025, 6:59 PM Tuning

Is the toolhead distances for the rapido v2 correct on the documentation? 15 messages

Jun 8, 2025, 1:34 AM Initial Setup

Unloading filament (Solved) 9 messages

Jun 8, 2025, 12:15 AM Tuning

disaster 87 messages

Jun 7, 2025, 6:46 PM Tuning

[SOLVED] Lane PREP error 30 messages

Jun 7, 2025, 12:55 PM Other

Oozing of filament on tool change. 6 messages

Jun 7, 2025, 3:36 AM Tuning

Where to poop 3 messages

Jun 6, 2025, 10:46 AM Initial Setup

Octopus Pro 1.0 RJ11 - CAN BUS 8 messages

Jun 6, 2025, 9:37 AM Build Issue

[SOLVED] Respoolers not respooling 33 messages

Jun 6, 2025, 2:26 AM Initial Setup

Click sound 2 messages

Jun 5, 2025, 11:58 AM Other

Loading lane squealing and error 5 messages

Jun 4, 2025, 9:24 PM Initial Setup

Wrong z height after filament change 16 messages

Jun 4, 2025, 5:47 PM Tuning

squish the poopy 22 messages

Jun 4, 2025, 12:34 PM Tuning Build Issue Other

Lost connection with Box Turtle 56 messages

Jun 3, 2025, 9:22 PM Other

[solved] problem on gate 0 5 messages

Jun 3, 2025, 7:13 PM Tuning Build Issue Other

I think I have a bug. 40 messages

Jun 3, 2025, 4:34 PM Initial Setup

Can’t resume 15 messages

Jun 2, 2025, 11:35 PM Tuning Initial Setup Other

Lost communication with MCU 'Turtle_1' 59 messages

Jun 1, 2025, 11:36 PM Other

New crazy noise coming from lane 2 20 messages

Jun 1, 2025, 10:47 PM Tuning

Initial Tool Load 7 messages

Jun 1, 2025, 8:59 PM Initial Setup

Poop doestn poop with petg 83 messages

Jun 1, 2025, 11:29 AM Tuning

Bowden length calibration never reaches tool had 71 messages

May 31, 2025, 7:10 PM Initial Setup

BT_LANE_MOVE LANE=2 DISTANCE=-50 directions inverted on 3, 4 15 messages

May 31, 2025, 5:23 PM Initial Setup

locked 2 messages

May 30, 2025, 11:56 PM Tuning Initial Setup

LEDs not working 4 messages

May 30, 2025, 10:11 PM Build Issue Initial Setup

HTLF will only start from Lane 4 39 messages

May 30, 2025, 9:22 PM Tuning Other

Missing .cfg files 6 messages

May 30, 2025, 5:13 PM Initial Setup

Should I adjust my bowden length manually 12 messages

May 29, 2025, 9:41 PM Tuning

BT retracts filament after tool load 8 messages

May 28, 2025, 11:26 PM Initial Setup Other

Lane 4 extruder not moving 8 messages

May 28, 2025, 8:10 PM Build Issue Other

stepper lane 2 reports error? 8 messages

May 28, 2025, 12:26 PM Other

[Solved] Lanes 2 and 3 bypassing Load Trigger on tool unload 5 messages

May 28, 2025, 3:41 AM Tuning Initial Setup

Flash Tool Error 31 messages

May 28, 2025, 2:05 AM Initial Setup

Too much purge in the wipe tower? 9 messages

May 27, 2025, 9:14 PM Tuning

BT did not pause 12 messages

May 27, 2025, 7:53 PM Other

Pillowing? 6 messages

May 27, 2025, 12:03 PM Tuning Other

Can't enter usb DFU mode 15 messages

May 27, 2025, 1:00 AM Build Issue

Roll on lane 1 triggers hub, can't print 70 messages

May 26, 2025, 7:33 PM Build Issue

attempting to print serial 33 messages

May 26, 2025, 1:11 AM Build Issue Initial Setup Other

load order 6 messages

May 25, 2025, 10:55 PM Initial Setup

[SOLVED] BT error state recovery 41 messages

May 25, 2025, 9:01 PM Tuning Initial Setup

extruder screw 12 messages

May 25, 2025, 6:45 PM Build Issue