Printer Profile

[scarlet maple]

I have the Fiberon™ PPS-CF10 - 0.5kg / Black and I am looking for some help creating a profile for it for the Qidi Plus 4 and I am also looking for a profile for the Panchroma™ Glow PLA
1.75mm (Old Packaging) / 1kg / Glow Blue for the same printer <@&1122587817768398938>

[old karma]

====================================            Fiberon™ PPS-CF10         ====================================== 
===================================         ENCLOSED AND HARDEND NOZZLE                ===================================
Slicer Settings
Nozzle Temperature: 300-320°C

Bed Temperature: 100-120°C

Print Speed: 30-50 mm/s
Density             1.35 g/cm³
Layer Height: 0.1-0.2 mm

Cooling Fan: Off (or very low)

Retraction: 1-2 mm at 20-30 mm/s

Adhesion: Use a PEI sheet or apply a thin layer of PVA glue stick on the bed to improve adhesion.

Additional Tips
Enclosure: Use an enclosure to maintain a stable printing environment and reduce warping.

Dry Filament: Ensure the filament is dry before printing. Store it in a dry box or use a filament dryer.

Nozzle Type: Use a hardened steel or ruby nozzle to prevent wear from the abrasive carbon fibers. when you make a profile these are  the right numbers and setting for polymakers carbon fiber ```

doesnt matter what slicer

 Panchroma™ Glow PLA:

Technical Specifications
Density: 1.24 g/cm³

Diameter: 1.75 mm

Recommended Slicer Settings
Nozzle Temperature: 190-230°C

Bed Temperature: 25-60°C

Print Speed: 40-60 mm/s

Layer Height: 0.1-0.2 mm

Cooling Fan: On (100%)

Retraction: 1-2 mm at 20-30 mm/s

Adhesion: Use a PEI sheet or apply a thin layer of PVA glue stick on the bed to improve adhesion

Additional Tips
Dry Filament: Ensure the filament is dry before printing. Store it in a dry box or use a filament dryer.

Nozzle Type: Use a hardened steel or ruby nozzle to prevent wear from the abrasive glow-in-the-dark particles. 

these numbers and setting should help a bit making a profile what is not bad to do if you want it perfect

[scarlet maple]

What about for the PolyLite™ CosPLA Verson A

[old karma]

ADD a custom fillament enter these things and try these settings in a slicer ```

============================================= PolyLite™ CosPLA Version A: ==============================
Density: 1.24 g/cm³

Diameter: 1.75 mm

Recommended Slicer Settings
Nozzle Temperature: 190-230°C
mostly 20% infill
Bed Temperature: 25-60°C
2 or 3 walls
bottom/top layer 3 or 4 0.6mm
this increasing strength and weight
Print Speed: 40-60 mm/s
adaptive cubic mostly works for all
Layer Height: 0.1-0.2 mm

Cooling Fan: On (100%)

Retraction: 1-2 mm at 20-30 mm/s

Adhesion: Use a PEI sheet or apply a thin layer of PVA glue stick on the bed to improve adhesion

Additional Tips
Dry Filament: Ensure the filament is dry before printing. Store it in a dry box or use a filament dryer. ```

should be for cosplay

[old karma]

All normal PLA you can do with a Normal Nozzle ================ALL like GLow and FIberon stuff or glitter in it lets say more rougher stuff Use a Hardend Nozzle

Use Dish Soap with hot water on the plates when you switch material or when they are new ................sometimes alcohol wont do it and watch out with towels with wash softener on it