nocturne iron
8 hr print blob .
This was bad bed adhesion that the print let go but lets see what you got. Remember this is to help others so show what happened and what you did to fix / cause of the problem
@foggy rune not quite pc-fr but a start at helping this never happen to another poor printer
deep girder
Legit 10 mins ago. #ruined for ever. @foggy rune 😂☺️🤣😁😬
calm panther
Didnt miranda also had something happen? Lol
elfin cape
Didnt miranda also had something happen? Lol
Now the "biggest" claim goes to Ivan😆
muted marsh
Always check your first layer and check on your printer as often as you can
Because I didn’t 
Last time imma try and print alot of little parts out of abs in one go
odd venture
This one pulled out the wires, and shorted the board. Killed the machine.
This one was PETG, and fused with the hot end brackets. Required replacing half the printed parts.
sick sail
This is a fun "competition". I'm imagining what a trophy for this would look like lol
muted marsh
This is a fun "competition". I'm imagining what a trophy for this would look lik...
A caked V6 hotend
nocturne iron
This is a fun "competition". I'm imagining what a trophy for this would look lik...
I have lots of pc-fr we can make one permanent🔥🔥
nocturne iron
This one pulled out the wires, and shorted the board. Killed the machine.
I did thay with a brass brush cleaning my nozzle on a purge hahahh i know the feeling ? Still have the board i have been trying my hand at micro soldering and would be an interesting project let me know i can cover shipping
calm panther
Who summoned me, I heard microsoldering 😆
deep girder
Lol this makes me mad I don’t have pictures of the golden blob of macro destruction
I had to toss the shroud and hotend lucky the backplate didn’t get it lol
calm panther
This one pulled out the wires, and shorted the board. Killed the machine.
Which one? Cartridge, thermistor or fan? Or all 3? Lol
odd venture
@nocturne iron That was the Monoprice Maker Select v2. They couldn't get me a replacement board, and offer to swap out the machine. Then botched that, and ultimately refunded me.
However, I do believe I have an SKR 1.3 or 1.4 around here somewhere that died from a wire brush, and powered on heater.
And another board where stepper drivers get fried as soon as they are installed.
nocturne iron
Who summoned me, I heard microsoldering 😆
As soon as i get home, trying to get more broken boards
iron hull
Not “big”, but big enough to take out my Sovol for now.
deep girder
Not “big”, but big enough to take out my Sovol for now.
That’s a good one @iron hull
calm panther
Not “big”, but big enough to take out my Sovol for now.
Thought that was chicken wire, lol
iron hull
Thought that was chicken wire, lol
No, the Sovol SV06 comes with a printed pattern on the build plate. Not sure why, since any PETG print pulls that pattern right off.
calm panther
Creality making interesting decisions, lol
deep girder
That’s wonderful Petg just erases the grid
torn forum
My largest printer blob. It’s supposed to be a KP3S fan duct printed in black ABS. The E3D v6 did need a good scrub after this smaller blob! Others ducts completed successfully after this.
wintry sequoia
Showing up with this cute multicolored set of… blobs🤣
deep girder
Mmm that’s was a good one lol Petg polymaker scientist lol
snow merlin
That time I tried ASA for the first time... I just went away few minutes and came back to a nice black worm.
Issue was bed adhesion, I ended using glue stick just to ensure that it sticks well cause we know how ASA and ABS is.
Also, if it wasn't for the sock, this could have ended pretty bad.
nocturne iron
Oh man that one looked perfect then Fail