#Revolt 3

85 messages · Page 1 of 1 (latest)

tight star
slate birch
#

anyone cram a 7900 xtx in their revolt 3 yet? I am thinking about swapping out my 2080s for one

prisma verge
#

The reference card fits just fine, but some of the AIB cards are using 4090 coolers so they will be too big

slate birch
#

cry-ang

#

with the gigabyte 7900 xtx elite I was thinking of honestly just 3d printing a spacer for the front panel

prisma verge
#

I'm not even sure if that card can fit into the front section of the case

#

since that card is super squared off, it might not clear the front pillar of the case

slate birch
#

The problem with the gigabyte card is the height/thickness of the card

#

Plus that’s what angle grinders are for 😎

#

I’ve done it once and I’ll do it again

49F9BC7C-5188-408E-B468-B43560645B04.jpg A231088F-96C7-4F53-8B5D-46DD582AE679.jpg
#

(What you can’t see are the drilled out rivets to allow the aio to sit in there)

prisma verge
slate birch
#

Card size
L=335 W=137 H=69 mm

#

Product page for the 7900 xtx elite

prisma verge
#

I think the squared off nature of the 7900 xtx elite and 69mm thickness is going to be very preventative here

#

Asrock 6900xt phantom gaming was the largest card I was able to fit without any modifications

#
  • 330 x 140 x 56 mm
#

the "attic" of the case has a bit that will restrict the width of any card longer than about 300mm at that point

#

It’s actually applying pressure against the side of the case and a tad diagonal

slate birch
#

nothing an angle grinder and modeling paint can't fix

#

the 7900xtx elite is a few mill smaller on the side so that might be fine
that entire corner will have to be gone though still I think :/

short oasis
#

Is the front io connector on the revolt 3 the same as the y60?

nimble bane
prisma verge
#

yes its the same combo connector as the other cases

short oasis
#

nice

gaunt cedar
#

Anyone try a Katana 5 Cooler inside of their Revolt 3?

#

Theoretically would fit...

#

I know Silver Soul 135 from Thermalright would fit - but it seems like a good trade between the two.

#

Currently running a Dark Rock TF though.

verbal wagon
#

Anyone managed to fit a 4080/90 into the revolt🤣

#

From what I am gathering the FE might have a chance

nimble bane
#

probably not recommened 😅

short oasis
#

doubt it

verbal wagon
tight star
verbal wagon
nimble bane
#

hence the 2 other posts

tight star
#

That sounds plausible

verbal wagon
forest prawn
#

Hi, i used a 90 degree adapter for the hdmi output from my rtx 3080 but it caused signal lost sometimes… thought about getting „foots“ for some space under my revolt 3. how did you guys managed this?

nimble bane
shrewd pilot
#

Anyone able to fit a Noctua 3070 in a revolt 3?

nimble bane
#

It physically wouldn't fit

#

That card takes up 4 slots

inland loom
#

The Hyte Revolt 3 is almost perfect, but I have some criticisms

#

Literally if some minor changes were made, it would be utter perfection

#

I'll list my critiques later when I rip my build apart

#

I've even "modded" the case in line with a particular criticism

#

That being the hard drive cage

#

The hard drive cage not being removable limits the thickness of radiators that can be installed, namely the Arctic Liquid Freezer II 280mm

#

I personally dremelled the cage out to fit this radiator, but if it were removable by default, it would be super useful for not only larger radiators, but also cable management etc

#

Here is the Arctic Liquid Freezer II 280mm with the hard drive cage removed

#

Adding official support for 2x80mm slim fans on the top would also be a nice improvement. Lots of people including myself have included 2 with minor elbow grease

#

I also plan on 3d printing a PCIe bracket to deshroud my GPU and 2x140mm fans to the third slot for improved thermals

#

I really think the removable hard drive cage should be the largest revision, as the industry is truly pivoting to thicker radiators, HYTE themselves are too lol

#

I'll post more nit-picks later

#

Full build pics

vocal zenith
#

Just finished putting together the Revolt 3 w/ the PSU... anyone else's PSU have this whistling coil whine on a low-mid load, the coil whine starts around 2 secs, you can hear the load gets higher around 13 secs.

I reached out to hyte's online support last week. They still haven't responded to me 🥲

vagrant sierra
#

I dunno for sure but at least with how the audio is coming in the video sounds more like a dragging ball bearing like as if the bearing on the fan is out-of-tolerance.

#

I of course would never recommend you to open up a PSU unless you know how to do so safely (making sure capacitors are fully discharged, etc). But I would have tried to replace the fan to see if that worked.

vocal zenith
vocal zenith
nimble geyser
#

The buzzing sounds electrical and not mechanical and also only happens under load

compact flame
#

my revolt3 case with psu came with only one pci-e cable, anyone know which type i need to order to replace? There appear to be a couple of different pinouts available on amazon. thermaltake appears different than corsair, etc.

vagrant sierra
compact flame
#

the psu is hyte, the one that came with the case.

#

I cant find hyte PSU specific cables

vagrant sierra
#

Yes. But Hyte doesn't manufacture their own PSUs so you'll have to try to find the OEM that built it for them and see if you can find PSU units that have the same OEM.

#

Even then... I would if possible test any "best guess" cables on some older hardware you can afford to lose before testing it on what will go into your final build... just in case the cable you got is the incorrect pinout

compact flame
#

I'll pull a spare GPU out of storage to test. I guess I could just order a couple of them and then do a side-by-side comparison to the hyte one, then test on a spare 7950 or something. Thanks. I'm surprised I can't order the pcie cable direct from hyte. Reaching support has been so far impossible 😐

prisma verge
#

the power supply should have come with 2 separate GPU power cables, one with a single 6 + 2 and one with dual 6 + 2

#

if you purchased the case new, I would contact the retailer about this

compact flame
#

I bought it new from Newegg. Was just looking to buy a cable rather than exchange the case from the retailer because I already built the system. It was with a 3060 at first while waiting for its final gpu, so I didn’t notice the missing pcie power cable until the new gpu came in 🤦 there are tons of different pcie cables on Amazon but none specifically for the sfxl-a700gd-ibp

#

Mine was missing the dual 6+2 or I’d be ok 🙂

hardy hull
#

Necro-ing this thread. But what would you recommend 240mm or 280mm aio for 5700x3D?

quaint forum
#

im finally building in this thing. i bought it for a build in 2023 but ended up going with another case. sold that pc and building a new one in the revolt.