grim cosmosBOT
Ahoi @pine ember!
It looks like you did not provide all the necessary information we need to help you.
Please upload your logfiles and a detailed description of your problem.
For further information see: https://docs.mainsail.xyz/faq/getting-help/discord#provide-information
Note: We only accept .log and .txt files as log files.
This is an automated message
tame sparrow
Why do you delete your message in the other thread and start a new one?
We still need a log, opening a new post, won't change anything on that fact
Also this is no Mainsail issue, but Klipper, so please fix your tags.
Mainsail is only a webpage and the message on your screen clearly says, Klipper reports
Also this is no error but only some kind of current status message
So the information we have is literally the text you wrote.....
pine ember
witch log file is needed?
pine ember
Why do you delete your message in the other thread and start a new one?
i was not sure it was Posted.
tame sparrow
witch log file is needed?
klippy.log
tame sparrow
i was not sure it was Posted.
Why? Because the bot asked for logs?
pine ember
Why? Because the bot asked for logs?
yeah i was not sure
i think i found the problem i did not flash the BTT Pico board right
i will try reflashing it.
tame sparrow
In the log, it says wrong path. So check the apth with ls /dev/serial/by-id
If the device wouldn't be flashed there would be some different kind of error
pine ember
no i know that i flash it wrong i made a mistake while config the klipper.bin file
but it could be that the pi isent dedecting that and it shows this error
pine ember
In the log, it says wrong path. So check the apth with `ls /dev/serial/by-id`
where shoud i check that. with ssh?
tame sparrow
Yes with ssh
tame sparrow
but it could be that the pi isent dedecting that and it shows this error
Ofc it can be that. To be sure just run lsusb and maybe disconnect it and run it again. If there was a change after unplugging, then it's at least detected by the system
pine ember
yeah sure
pine ember
i reflasht the board this time right, but the error message is still there
This was the message when i checkt with ls /dev/serial/by-id : usb-Klipper_rp2040_454741505B8CF9DA-if00 usb-STMicroelectronics_STM32F042F6P6_CDC_in_FS_Mode_A03A31434E56-if00
tame sparrow
Then change the serial path according to the stm path
So it should be:
/dev/serial/by-id/usb-STMicroelec... and so on
pine ember
okey and what now
again the error message is showing: mcu 'mcu': Unable to connect...
pine ember
Klippy?
tame sparrow
Yes
pine ember
tame sparrow
Did you read my message? I wrote /dev/serial/by-id/usb-STMicroelec... and not /dev/serial/by-id/usb-Klipper...
/dev/serial/by-id/usb-STMicroelectronics_STM32F042F6P6_CDC_in_FS_Mode_A03A31434E56-if00
That's the correct path
pine ember
ou sorry
tame sparrow
The path in there isn't even the same as the other one. It's just some random path that you copied from the internet(?)....
pine ember
no its from a config file i found on github for voron 0 i was thinking maybe this on will work.
tame sparrow
Don't copy random addresses. They won't work 🙈
pine ember
yeah i know now ...
my first time
its still showing: Klipper reports: STARTUP
Printer is not ready
The klippy host software is attempting to connect. Please
retry in a few moments.
tame sparrow
That is no error
That message will always pop up
It just says that Klipper is starting right now
After a while it will show you the correct error
If it shows the error (red panel), send a new log
pine ember
its loading like 5 min is this normal?
tame sparrow
It shouldn't. Did you press some button, or did you let it alone for 5mins now?
pine ember
i reloded the page
tame sparrow
You can, but it shouldn't make a difference
Press it once and then just wait until it switches to a red error screen
tame sparrow
It's already red?
pine ember
no
pine ember
nothing happend when i presst the firmware restart button
pine ember
oke i wait...
pine ember
oke somthing isent right its still in this blue screen?
I eating now i will check after i finisht
tame sparrow
If it still is on the blue screen after you finished eating, open a ssh session and run following commands and send the output:
cd ~/klipper
git status
git remote -v
what shoud happen?
pine ember
the commands?
pine ember
tame sparrow
And the first one?
That's the output of the third command, but I also need the output of the second command. The first command has no output
tame sparrow
Send a log
pine ember
tame sparrow
And then just wait, as I don't know the answer and ask someone
Klar, der Fehler im og, zeigt, dass er nicht kommunizieren kann, aber dann sollte er doch wenigstens nicht ewig hängen bleiben
pine ember
true
would reflashing both boards help?
i have reloded the page and now this is showing:
tame sparrow
Run systemctl status klipper
