Hello how to add 3d touch/bl touch to klipper ? | Mainsail | Page 1

rare trout Oct 3, 2023, 1:29 PM

#

pls help

vapid wigeon Oct 3, 2023, 1:31 PM

#

https://www.klipper3d.org/Config_Reference.html#bltouch

rare trout Oct 3, 2023, 1:31 PM

#

what with that?

vapid wigeon Oct 3, 2023, 1:31 PM

#

Did you read it?

rare trout Oct 3, 2023, 1:32 PM

#

I need to paste the frist one ?

vapid wigeon Oct 3, 2023, 1:32 PM

#

Did you read it?

rare trout Oct 3, 2023, 1:32 PM

#

ye

vapid wigeon Oct 3, 2023, 1:33 PM

#

So it tells you what exactly to add to your printer.cfg and how to configure it correctly

#

And if you didn't saw it. It links to the bltouch guide too: https://www.klipper3d.org/BLTouch.html

rare trout Oct 3, 2023, 1:37 PM

#

but

#

I need something simple

#

do you have something to paste

#

on ender 3 v2

vapid wigeon Oct 3, 2023, 1:39 PM

#

No, I don't have something to paste, as it's different for literally every setup

#

That's why you need to read through this or search for another quick guide online.

#

Only thing I can say is that you most likely need the following:

[bltouch]
sensor_pin:
control_pin:
x_offset:
y_offset:
```And then you need to follow this to calibrate your z-offset: https://www.klipper3d.org/Probe_Calibrate.html#calibrating-probe-z-offset

rare trout Oct 3, 2023, 1:42 PM

#

#

okey

#

how to repair it

vapid wigeon Oct 3, 2023, 1:42 PM

#

What does it say?

#

There is missing something inside a section of your printer config

#

Look at that guide again: https://www.klipper3d.org/BLTouch.html
Abovce the second code block, there it gets explained

rare trout Oct 3, 2023, 1:44 PM

#

#

vapid wigeon Oct 3, 2023, 1:44 PM

#

rare trout

Why do you write it on the same line?

rare trout Oct 3, 2023, 1:45 PM

#

where

vapid wigeon Oct 3, 2023, 1:45 PM

#

The thing missing in your safe_z_home section

rare trout Oct 3, 2023, 1:45 PM

#

this is good ?

#

vapid wigeon Oct 3, 2023, 1:45 PM

#

Yes

#

If that's a safe possition

rare trout Oct 3, 2023, 1:45 PM

#

ugh

#

I think its working

#

what now

vapid wigeon Oct 3, 2023, 1:46 PM

#

I gave you already all you need. I won't help you by every step, sry

rare trout Oct 3, 2023, 1:47 PM

#

I think ist working

vapid wigeon Oct 3, 2023, 1:47 PM

#

Just remember, everyone here is doing it in their freetime

#

Then calibrate your offsets, especially the z_offset: https://www.klipper3d.org/Probe_Calibrate.html#calibrating-probe-z-offset

rare trout Oct 3, 2023, 1:48 PM

#

okey its doing mesh

#

offsets ?

#

I need to do probe offset ?

vapid wigeon Oct 3, 2023, 1:50 PM

#

As long as your probe isn't your nozzle, yes

rare trout Oct 3, 2023, 1:50 PM

#

okey

#

and something more ?

vapid wigeon Oct 3, 2023, 1:50 PM

#

No

rare trout Oct 3, 2023, 1:51 PM

#

okey I have offet

#

where I need to paste it

vapid wigeon Oct 3, 2023, 1:52 PM

#

https://www.klipper3d.org/Config_Reference.html#bltouch

rare trout Oct 3, 2023, 1:52 PM

#

its this ?

#

vapid wigeon Oct 3, 2023, 1:53 PM

#

That is for your z_offset yes

rare trout Oct 3, 2023, 1:54 PM

#

ok have it

#

I will se if its working

#

weird

vapid wigeon Oct 3, 2023, 1:54 PM

#

Did you also calibrate x and y offsets? How did you get the z_offset?

rare trout Oct 3, 2023, 1:54 PM

#

I make 38.55

#

bc 38.55 offset from nozzle to 3d touch

#

#

#

so maybe its x offset ?

vapid wigeon Oct 3, 2023, 1:56 PM

#

38.55 souns wrong for z_offset

#

z is height

rare trout Oct 3, 2023, 1:56 PM

#

yd

#

ye

#

so what is for

#

its for x ?

vapid wigeon Oct 3, 2023, 1:57 PM

#

How should I know it?

#

I don't have your printer in fron of me

#

I'm no omniscient being

rare trout Oct 3, 2023, 1:57 PM

#

but wait

#

I need to make it on -

#

like if its showing me 38.55 mm I need to make it -38.55

vapid wigeon Oct 3, 2023, 1:58 PM

#

Yes that could be. As I said, no idea

#

I have no magic glass bowl and I'm not an omniscient being.

rare trout Oct 3, 2023, 2:00 PM

#

yep I think its on -

#

but when its homing I have this weird gap

#

its z ofset ?

vapid wigeon Oct 3, 2023, 2:00 PM

#

I don't know what you set, but it could be

#

I don't see the gap or anything of your setupo

rare trout Oct 3, 2023, 2:01 PM

#

no not in code

#

I will show you

#

vapid wigeon Oct 3, 2023, 2:02 PM

#

rare trout no not in code

But it's depending on your settings

#

So what gap do you now mean?

#

Does it say that it's at 0?

rare trout Oct 3, 2023, 2:03 PM

#

no

#

its says its on 10

vapid wigeon Oct 3, 2023, 2:04 PM

#

So what gap do you mean?

rare trout Oct 3, 2023, 2:05 PM

#

this

#

#

ah

#

it was z hop

#

form safe home

#

okey I think I repair it

#

#

its is on 3 mesh point

#

how I could repair it

#

?

vapid wigeon Oct 3, 2023, 2:07 PM

#

That says that it moved as far as it could but the probe didn't trigger

#

So reduce your z_min or level your bed manually first

#

And make suree that the z_offset is correct

rare trout Oct 3, 2023, 2:08 PM

#

okey I will level my bed

#

how I could do z offset

#

and where is it

#

ahhhhhhhh

#

its not homing

#

do I need to turn my z motor ?

#

I mean

#

this

#

vapid wigeon Oct 3, 2023, 2:12 PM

#

No need to change anything there, if it's moving correctly

vapid wigeon Oct 3, 2023, 2:12 PM

#

rare trout how I could do z offset

I already sent it multiple times:
https://www.klipper3d.org/Probe_Calibrate.html#calibrating-probe-z-offset

rare trout Oct 3, 2023, 2:20 PM

#

okey I will frist manually level bed

#

can stepper z be as normal

#

do I need to turn it off

vapid wigeon Oct 3, 2023, 2:23 PM

#

If you turn of your stepper z, then you won't be able to move your z axis anymore....

rare trout Oct 3, 2023, 2:34 PM

#

ahh

#

I dont really know how to make it

#

okey I leveled my bed manualy

#

I will try mesh

#

do I need safe z home ?

#

I mean

#

I dont feel like I need it

#

okey nvm I need it

rare trout Oct 4, 2023, 5:38 AM

#

Okey now I know what I need to do but I have question do homing need to be on center off printer

#

?

vapid wigeon Oct 4, 2023, 10:05 AM

#

It can be everywhere you want. Just change safe_z_home

sly grotto Oct 4, 2023, 12:34 PM

#

to be more precise, it can be anywhere within the limits of you x,y min and max

rare trout Oct 4, 2023, 3:34 PM

#

okey I made z offset

#

and my x and y

#

I have problem

#

what was command for extenting 3d touch

#

you know to see if its working

vapid wigeon Oct 4, 2023, 3:38 PM

#

https://www.klipper3d.org/BLTouch.html#initial-tests

rare trout Oct 4, 2023, 3:39 PM

#

oh yes this th

#

thx

#

ugh

#

I think I set my z offset wrong

#

I mean

#

it was good

#

I mean

#

when it was on 0

#

and I moved the nozzle to 0,55 mm height I was good

#

but when I paste it into printer.cfg its to hight

vapid wigeon Oct 4, 2023, 3:46 PM

#

I recommend you to use this guide: https://www.klipper3d.org/Probe_Calibrate.html#calibrating-probe-z-offset
That will add a section at the bottom of your file, that can be edited directly on the dashboard.

rare trout Oct 4, 2023, 3:47 PM

#

aaaa

#

I need to make it here ?

#

bc I aded it in here

#

#

yyyyy

vapid wigeon Oct 4, 2023, 3:48 PM

#

Like I said, follow that guide. Then it should automatically comment that offset out and add a new thing at the very bottom, iirc

rare trout Oct 4, 2023, 3:48 PM

#

weird

#

now its to height

#

how to repair it

vapid wigeon Oct 4, 2023, 3:50 PM

#

How often should I tell you again, to follow that guide?

#

It's there for a reason and I mention it for a specific reason

#

If you want I paste it you here, then you got your explanation on how to fix it....

vapid wigeon Oct 4, 2023, 3:52 PM

#

vapid wigeon I recommend you to use this guide: https://www.klipper3d.org/Probe_Calibrate.htm...

After you finished that guide, you should print a first layer test, and then use that buttons to set a new offset. Then print another first layer test, until you got a good first layer

rare trout Oct 4, 2023, 3:52 PM

#

I think I have it

#

yeees I have it

#

yay

#

I GOT IT

#

oh no

#

I have move out off range

#

I need to fix it

#

the scref tilts are screw positions ?

#

yep its it

#

Ah I stiil have it

#

I have move out off range

#

how to set range ?

vapid wigeon Oct 4, 2023, 4:04 PM

#

Inside the stepper sections, but I guess it's during homing, then you sould fix your bed_mesh section

rare trout Oct 4, 2023, 4:04 PM

#

what wrong here

#

vapid wigeon Oct 4, 2023, 4:05 PM

#

Most likely mesh_min and mesh_max

rare trout Oct 4, 2023, 4:05 PM

#

I am doing it on ender 3 v2

vapid wigeon Oct 4, 2023, 4:05 PM

#

I don't know your offsets or bed size, so I cannot help you any further

rare trout Oct 4, 2023, 4:05 PM

#

so mesh max is my buildplate ?

#

you mean print are or bed size ?

#

area

vapid wigeon Oct 4, 2023, 4:06 PM

#

No, it's the position of the extruder while meshing.

vapid wigeon Oct 4, 2023, 4:06 PM

#

rare trout you mean print are or bed size ?

print area ofc

rare trout Oct 4, 2023, 4:06 PM

#

okey so its 220x220

vapid wigeon Oct 4, 2023, 4:06 PM

#

And what yre your offsets?

rare trout Oct 4, 2023, 4:06 PM

#

offsets off bl touch?

vapid wigeon Oct 4, 2023, 4:06 PM

#

Of what else?

rare trout Oct 4, 2023, 4:07 PM

#

?

vapid wigeon Oct 4, 2023, 4:07 PM

#

What other offsets should be there?

rare trout Oct 4, 2023, 4:07 PM

#

idk

vapid wigeon Oct 4, 2023, 4:07 PM

#

What is generating your mesh?

rare trout Oct 4, 2023, 4:07 PM

#

ye

vapid wigeon Oct 4, 2023, 4:07 PM

#

Ofc I mean the bltouch offsets

rare trout Oct 4, 2023, 4:07 PM

#

oke

#

so my x offset is -38,55 y -10 and z 2.2

#

and what now ?

#

hm?

vapid wigeon Oct 4, 2023, 4:11 PM

#

As I already said, I'm doing this in my freetime

#

So if I don't answer immediately, just chill

#

I don't get paid for this

rare trout Oct 4, 2023, 4:11 PM

#

yeh sorry

vapid wigeon Oct 4, 2023, 4:12 PM

#

So your bed_mesh should be something like that:

mesh_min: 40, 15
mesh_max: 215, 215

#

You got out of range because to mesh the point 15, it would have need to go to -23.55

#

And that is ofc, outside of your print area

rare trout Oct 4, 2023, 4:14 PM

#

okey

#

I think I made better x offset

#

how you made it ?

#

bc I mesured again better way my x offset and its -44

vapid wigeon Oct 4, 2023, 4:17 PM

#

I just looked at your offsets and went a bit higher.
Like I said. If you want to mesh point 100,100, your extruder tries to go to 61.45,90

#

Then go with mesh_min: 45, 15

rare trout Oct 4, 2023, 4:17 PM

#

okey thx

#

lets see if its working

#

no again

#

#

how to repair it

#

#

here are my settings

vapid wigeon Oct 4, 2023, 4:22 PM

#

Send your printer.cfg

rare trout Oct 4, 2023, 4:22 PM

#

give me sec

#

I think I found good redit about it

vapid wigeon Oct 4, 2023, 4:23 PM

#

Oh, I messed up there. It should be the other way around.

#

So it would be:

mesh_min: 5, 5
mesh_max: 175, 205

#

So it's the possition of your bltouch ofc

#

And the extruder has to stay inside your print area

rare trout Oct 4, 2023, 4:27 PM

#

okey

#

I will see

#

YEEEEEEEEEEEEEEEEEEEEEEEEP ITS WORKING

#

YOU ARE THE BEST

#

and I have one more thing

#

how to add filament sensor

vapid wigeon Oct 4, 2023, 4:33 PM

#

I don't know. I can just link the config section: https://www.klipper3d.org/Config_Reference.html#filament_motion_sensor

rare trout Oct 4, 2023, 4:50 PM

#

hey

#

it this good mesh ?

#

#

I mean I need to adjust the screw or its automaicly adjusting it

#

?

vapid wigeon Oct 4, 2023, 5:15 PM

#

How should it adjust the screws?
It will move according to your mesh, if you got it loaded, but the screws won't change

vapid wigeon Oct 4, 2023, 5:15 PM

#

rare trout

I wouls say, it's good enough

#Hello how to add 3d touch/bl touch to klipper ?