Hey friends,
deej does nothing.
- deej 0.9.10 installed
- 340 driver installed
- Com port correct
- Aduino IDE works
- Pins correctly attached and soldered
- I am fully hydrated and well fed=)
- Arduino blinks shortly when opening deej
Can you help?
#Deej still not working
worthy edge
earnest radish
run deej-debug or deej-dev and post the output
cobalt remnant
does the serial monitor in the arduino IDE work?
earnest radish
does the serial monitor in the arduino IDE work?
i believe thats what the 4th bullet point means
cobalt remnant
i believe thats what the 4th bullet point means
then it's likely the driver problem had to go through 2 versions to get it to finally work namely 3.4 and 3.9
worthy edge
Problem identified!
He took my soundbar, which i never use, as master volume...
Now researching that.
Not solved yet, I keep you updated.
Solved. The solution was.
WIN + CNTRL + V.....
Switch output manually once!
Guess who helped me come to that conclusion.....=)
kindred jungle
Solved. The solution was.
WIN + CNTRL + V.....
Switch output manually once!
Sorry to reopen a solved thread, but I'm facing a similar issue and trying to troubleshoot further.
Could you elaborate more on the solution?
worthy edge
Ofc.
I did all the fixes mentioned above.
My windows used my soundbar as "master".
Press Win + Ctrl + v
Switching this around reset "master" to the default windows sound. That was it.
Sry. My physical speakers.
The knob changed the speaker, not the master volume.
I switched it and suddenly the "master" volume was correctly recognized.
kindred jungle
Ofc.
I did all the fixes mentioned above.
My windows used my soundbar as "master...
Oh maybe I misunderstood your initial post... was deej-debug working beforehand as well?
worthy edge
Yes. Everything worked, but I needed to switch around my output devices to reset my "master" to windows volume.
Just windows things I guess.
But I stumbled upon every issue on the way.
Where are you stuck?
kindred jungle
Yes. Everything worked, but I needed to switch around my output devices to reset...
Pots show values changing on serial monitor, but debug.exe doesn't show any inputs when turning the pots. I've tried a few different drivers, no change :/
worthy edge
Did you change the Com in the deej config?
kindred jungle
Did you change the Com in the deej config?
That's all configured correctly, yep. Comm hasn't changed after driver rev uninstall/reinstall attempts
worthy edge
Feed chatgpt with your infos. He ran me through arduino ide and all the troubles on the way.
I copied the debug into it and he tld me where the problem lies.
Have you closed the Arduino IDE?
Is deej even starting and pops up in the botten right tray?
kindred jungle
Have you closed the Arduino IDE?
Is deej even starting and pops up in the botte...
Yup and yup
Its 100% a driver issue as far as I can tell
worthy edge
So we can say for sure that Deej doesnt get access to the correct com port.
If it actually starts... Well. At exact that moment, I figured out that my knob regulated the wrong output device. It worked when I switched to my jeeco speaker and with that, anywhere in windows, master was set correctly again.
Try if your knob changes sound on any other device.
Otherwise tell ChatGPT the following:
Im setting up a volume slider in arduino with deej
Arduino IDE monitor shows it works
Deej config is setup correctly
Correct com
Here is the debug report
Than copy paste the debug
kindred jungle
So we can say for sure that Deej doesnt get access to the correct com port.
If i...
Oh it 100% connects to the correct device and comm port
kindred jungle
So we can say for sure that Deej doesnt get access to the correct com port.
If i...
worthy edge
Frustrating. What does GPT say?
kindred jungle
Frustrating. What does GPT say?
Haven't attempted it yet, currently at work
worthy edge
LOL. I can reproduce my problem. 🙂
earnest radish
@worthy edge so reading through this.. seems that deej was indeed working and doing its job you just had your audio devices configured wrong