Don't have any idea what to say, thing this: https://www.printables.com/de/model/476143-elegoo-neptune-3-max-first-layer-calibration-test
First print after the default model.
#First layer test gone wrong
brave gull
Mostly concerned with the right back corner
fringe scarab
Still not good
brave gull
but
- I feel like it is too far back
- yeah probably
but also pulling an A4 under it... is hard
if I'd put it lower it might rip.
fringe scarab
Its not ?
junior flare
check if your cura printer has the correct bedsize
brave gull
check if your cura printer has the correct bedsize
It even has a lower one
junior flare
okay .... you sure you got the right printer
brave gull
Anyways, brought it down another 15 mm
junior flare
thats weird the neptune3 pro should have a 225 x 225 x 280 mm print bed
brave gull
It does!
and the cura has this
Wired...
Anyways made the model smaller
AHW did not remove the skirt this time! xD
it has a brim
damn
canceling.
are you sure the extrude speed isn't too low? and that it needs to go lower?
I am scared of fucking up my bed
@fringe scarab
@junior flare
Also half time tank you both :D
junior flare
every ping costs now a dollar to the "chemicalargtist retirement" fond or to your local animal shelter 😄
has your printer something like informations on the display? the bed size is really od
brave gull
xD
brave gull
has your printer something like informations on the display? the bed size is rea...
yeah? like what do you want to know? :D
I feel like the size is not the problem, but the bed is too far in the front (down)
pic of the first try made it look that way
brave gull
the second too.
brave gull
at 2.07 it still is not close enough
fringe scarab
you rlly need to be close
like the paper you need to force a little bit for move it
https://www.youtube.com/watch?v=uF5mUDcVzTM&ab_channel=AntonioAlì not the same printer but you see what the paper need to look like
brave gull
like the paper you need to force a little bit for move it
already beyond that
brave gull
Nope
fringe scarab
hum that rlly strange
brave gull
okay going to 2.30
brave gull
got a neptune 3
this is the one I am currently trying
I have made adjustments
The souce is https://www.printables.com/de/model/476143-elegoo-neptune-3-max-first-layer-calibration-test
Ooooo current iteration looks promissing
junior flare
hmmm if it works otherwise .... there is no command for using that mesh you made
brave gull
there is no command for using that mesh you made
What?
junior flare
M82 ;absolute extrusion mode
;ELEGOO NEPTUNE 3 Pro
M220 S100 ;Set the feed speed to 100%
M221 S100 ;Set the flow rate to 100%
G90
G28 ;home
**;M420 S1 Z10;Uncomment to enable progressive compensation height of **10mm
G92 E0 ;Reset Extruder
you did the part where it probed the bed right?
junior flare
if it works i wont say anything if not i recommend you change the start script
but if you change the start script reset your z offset to avoid the printer ramming itself into the bed
and adjust it live during a print
brave gull
The auto leveling puts it ~at 2.17
I need it at 2.50+ I feel like I am fucking up my bed.
junior flare
the abl creates a mesh but not an auto z offset
the autobed level creates a height map from a known point
your z offset is usally adjusted manualy
brave gull
Like... better at 2.50
how much more...
@junior flare 2.50 is ripping if I put a paper under it. Yet is not perfect.
brave gull
neatly scratched my bet at 2.6 after printing with 2.5, then moving the Z offset live and finding out that 2.4 is best, even tough the try b4 2.5 was not enough???
brave gull
try the change in your start script i highlited
No, don't worry
it was not your script
brave gull
Hmm, not sure. I don't want to mess with that yet. Will print a benchy and then come back the next time I got time.
brave gull
Again, thank you two for your time ^^ @fringe scarab @junior flare