silk flint
I checked:
Anyone have ANY ideas?
wary notch
please take a focused picture of just one layer on the bed
silk flint
That’s pretty focused and it’s only one layer
pallid jacinth
i had a similar issue where my first layer was bad and i fixed it by installing jyers firmware with ubl 10x10 bed leveling or whatever its called lol. It levels 100 probe points on the bed instead of 9 so its more accurate. i think this worked for me because my bed was warped in some spots but then again im still new to 3d printing and idk
hope this helps
also im pretty sure there is better firmware out there but thats the one i used
@silk flint
silk flint
i had a similar issue where my first layer was bad and i fixed it by installing ...
Issue is I can’t flash firmware into my printer anymore for some reason 😅 since I did the bltouch firmware it stopped reading new firmware
silk flint
also please attach the gcode
pallid jacinth
Issue is I can’t flash firmware into my printer anymore for some reason 😅 since...
Make sure to reformat it
silk flint
Make sure to reformat it
How? I’ve sent M502 and M500 and no dice
pallid jacinth
Right click on your pc and click format
On the sd card file
Make sure you click on the sd card lol, don’t wanna accidentally reformat your main drive 💀
It should be FAT32
Keep in mind it will delete your files on it so back up everything you need to keep
silk flint
Reformat the sd card
Tried that already with multiple sd cards, both long and short format FAT32
Even tried installing firmware to the screen but it didn’t work (thank god too because I realized I had the type of board that would’ve been fried from the firmware I was trying to install 💀💀)
wary notch
what size nozzle is this?
and what are you naming the firmware when you put it on the sd card?
your extrusion heights AND widths are set to 0.3mm in Cura, which doesn't make sense for any nozzle size. if you are using a 0.3mm nozzle you should lower your height. if you are using bigger than 0.3mm nozzle you should raise your width to AT LEAST that size.
silk flint
what size nozzle is this?
0.4mm nozzle so ~80% is 0.3mm I thought that was the max?
I tried both the default name and “firmware”
You’re saying my line width should be the same as my nozzle size, even if the layer height is less?
wary notch
the width should be 0.4mm or larger, up to like 0.6mm or so. and the height at 80%ish of 0.4mm or less
iirc creality boards won't flash new firmware unless it has a different name than the previous flash
if you still have issues after width changes. please take a picture of LITERALLY ONE SINGLE LAYER on the bed, please. 🙂
silk flint
Thank you 😎👍
@wary notch btw do you recommend I get a different type of plate? Currently with the default glass one
wary notch
I think that coated glass is fine, but having to wait for it to cool to remove parts can be inconvenient
silk flint
@wary notch 215*C nozzle, print profile from a friend, new bed, new nozzle, light layer of glue and it’s STILL lifting
wary notch
please attach the gcode and take a more focused picture. Nothing can be seen in the first photo
silk flint
It’s as focused as my camera will get it lol. No disrespect but I can’t shoot in 24MP and I just need troubleshooting, not fine tuning
wary notch
no. you need to tap on your screen to focus what you want. your cooler and your thumb look great
silk flint
It’s black on black man lol. Also I DID tap the screen to focus
I just need advice on what to do when there’s crappy bed adhesion
wary notch
your first layer doesn't look the best. it's possibly nozzle too close to the bed or overextrusion.
it also looks inconsistent, or is that just the photo?
silk flint
No it’s def inconsistent
wary notch
also attach the gcode
silk flint
Nozzle too close can cause lifting?
wary notch
so it's different on the left vs the right of the bed?
silk flint
so it's different on the left vs the right of the bed?
I’m not sure because the entire thing is very inconsistent
wary notch
I know your phone takes better pictures, dude
silk flint
Yes it does but apparently it doesn’t like my build plate can we please drop this
wary notch
attach the gcode
wary notch
what exactly is the "bed adhesion issue"? the corners are curling up during the print or?
silk flint
Yes and edges are raised on the first layer
wary notch
I'd say your nozzle is too close to the bed causing the first layer to go down thin and terrible and then peel up.
