Tx16s not loading lua script for Elrs | ExpressLRS Community | Page 1

tawny pumice Aug 27, 2025, 6:28 AM

#

I recently got myself a beta fpv air 65 tiny whoop and a ranger elrs module, as I was trying to update the elrs module to 3.3.0 (that is what the air 65 uses) and something must have happened as I am now unable to open the lua folder to turn on binding. If anyone could help that would be great, thank you.

orchid sluice Aug 27, 2025, 6:28 AM

#

can you post a screenshot/photo of the current model settings (external rf section) please

tawny pumice Aug 27, 2025, 6:31 AM

#

orchid sluice Aug 27, 2025, 6:31 AM

#

tawny pumice

increase the external rf baud rate to 5.25M

tawny pumice Aug 27, 2025, 6:32 AM

#

Okay i just did it, still stuck on the loading

orchid sluice Aug 27, 2025, 6:33 AM

#

tawny pumice Okay i just did it, still stuck on the loading

can you inspect the module bay and make sure no pins are bent, and the 3 important pins at the bottom are properly engaging with the tx module?

#

what does the tx module's RGB Led show? what pattern or color?

tawny pumice Aug 27, 2025, 6:35 AM

#

pins are straight and dont seem to have any damage, there isnt any color for the module bay

orchid sluice Aug 27, 2025, 6:35 AM

#

tawny pumice pins are straight and dont seem to have any damage, there isnt any color for the...

it's the module's RGB LED that I'm asking about

tawny pumice Aug 27, 2025, 6:37 AM

#

There isnt any led from what i can see

#

No color

orchid sluice Aug 27, 2025, 6:37 AM

#

no color here in the logo

tawny pumice Aug 27, 2025, 6:37 AM

#

no

orchid sluice Aug 27, 2025, 6:38 AM

#

tawny pumice no

take out the module from the radio
reflash it via uart/usb, with erase before flash enabled

#

guide's here: https://www.expresslrs.org/quick-start/transmitters/rm-ranger/#via-uart

tawny pumice Aug 27, 2025, 6:38 AM

#

ok will try

#

ok did it and now the logo is flashing between orange and green

orchid sluice Aug 27, 2025, 6:43 AM

#

orange and green or yellow and green?

#

or yellow-green and green

tawny pumice Aug 27, 2025, 6:43 AM

#

hard to tell its flashing so quick

#

yellow green green describes it best

#

green pulses twice

orchid sluice Aug 27, 2025, 6:44 AM

#

have you already flashed it via uart or you just connected it to uart/usb?

tawny pumice Aug 27, 2025, 6:44 AM

#

i already flashed it

orchid sluice Aug 27, 2025, 6:44 AM

#

tawny pumice i already flashed it

what value did you set for "auto-wifi"?

#

did you set it to 0?

tawny pumice Aug 27, 2025, 6:45 AM

#

not sure what you mean i dont see an option for auto wifi

orchid sluice Aug 27, 2025, 6:46 AM

#

tawny pumice not sure what you mean i dont see an option for auto wifi

did you flashed with "Erase before flash" enabled?

tawny pumice Aug 27, 2025, 6:46 AM

#

yes

orchid sluice Aug 27, 2025, 6:47 AM

#

tawny pumice yes

can you disconnect the usb cable from the module and reconnect it?
and observe what LED pattern would be shown?

tawny pumice Aug 27, 2025, 6:47 AM

#

flashing an orange color now

orchid sluice Aug 27, 2025, 6:48 AM

#

tawny pumice flashing an orange color now

okay. disconnect from usb and put it back into the radio.. then try opening the lua script again

tawny pumice Aug 27, 2025, 6:49 AM

#

its changed again now back to the same yellow green thing

orchid sluice Aug 27, 2025, 6:50 AM

#

tx modules, when not getting valid CRSF packets from a handset/radio will boot starting with that rainbow unicorn puke (boot up sequence), then goes to orange blinks (indicating it isn't getting valid CRSF packets), and after the set auto-wifi interval (60s by default), it will go into wifi mode indicated by the yellow-green -green blink/fade pattern

tawny pumice Aug 27, 2025, 6:51 AM

#

seems to be working now

#Tx16s not loading lua script for Elrs