that line is of no consequence..
could you post the full !log file please
#Pre-connection option "no_reset" was selected.
quiet yarrow
quiet yarrow
also, what does the receiver LED do? does the receiver LED blink?
slim atlas
also, what does the receiver LED do? does the receiver LED blink?
nope it does not blink
slim atlas
https://cdn.discordapp.com/attachments/798006228450017290/1025339571979960340/Lo...
======== PASSTHROUGH INIT ========
Trying to initialize COM3 @ 420000
Attempting to detect FC UART configuration...
** Serial RX config detected: 'serial 1 64 115200 57600 0 115200'
Enabling serial passthrough...
CMD: 'serialpassthrough 1 420000'
======== PASSTHROUGH DONE ========
======== RESET TO BOOTLOADER ========
- Using full duplex (CRSF)
Cannot detect RX target, blindly flashing!
esptool.py v4.2.1
Serial port COM3
WARNING: Pre-connection option "no_reset" was selected. Connection may fail if the chip is not in bootloader or flasher stub mode.
Connecting...
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
slim atlas
what vtx is on the drone? digital? analog?
its a rdq mach 3 vtx idk what it is but it works with my analog
quiet yarrow
its a rdq mach 3 vtx idk what it is but it works with my analog
has the receiver LED ever blinked before?
slim atlas
yes it was working earlier today until I flashed it
quiet yarrow
why did the receiver got bricked?
slim atlas
I dont know I flashed it and now its bricked
quiet yarrow
I dont know I flashed it and now its bricked
what did you flashed it with?
slim atlas
quiet yarrow
here are your options:
-
reflash the receiver via uart adapter FOLLOWING the procedure here: https://www.expresslrs.org/quick-start/receivers/hmep2400/#via-uart
-
FOLLOW the Unbricking guide step-by-step here: https://www.expresslrs.org/quick-start/unbricking/
slim atlas
thank you, will let you know how it goes
quiet yarrow
for sure, especially if it didn't go well
slim atlas
here are your options:
1. reflash the receiver via uart adapter FOLLOWING the pr...
it doesnt say anything about the error messages and I dont have the device used for the first one
what im trying to do is change the "no reset" setting
quiet yarrow
it doesn't mean anything in this context. ignore it
slim atlas
@quiet yarrow what else could I possibly do?
quiet yarrow
<@779307690040098817> what else could I possibly do?
have you FOLLOWED the steps of the unbricking procedure?
slim atlas
yes
quiet yarrow
yes
and you haven't thought of ordering a uart adapter if you don't have one?
what about ordering or swapping in another receiver while you wait for the adapter?
slim atlas
ill just buy a new receiver I guess
quiet yarrow
ill just buy a new receiver I guess
does the receiver power up when you plug in usb?
slim atlas
only if the battery is also plugged in
quiet yarrow
only if the battery is also plugged in
did you bridged the boot pad?
slim atlas
yes
slim atlas
wait do I have to do it while the battery is plugged in
what I did was unplugged everything, soldered it, then plugged the battery in
quiet yarrow
wait do I have to do it while the battery is plugged in
what does the step-by-step say?
slim atlas
If you've connected a LiPo from the previous step, disconnect it. Also, unplug the Flight Controller from your computer.
Prepare the receiver for bootloader mode.
If your Receiver have boot pads, bridge them together with solder.
If your Receiver has a button, use an alligator clip to keep the button pressed.
If your Receiver only has one Boot pad, connect it to a Ground pad.
quiet yarrow
did it say to plug in lipo?
slim atlas
its still not working even though ive done everything the step-by-step said
quiet yarrow
its still not working even though ive done everything the step-by-step said
when did you power up the receiver?
slim atlas
around a minute after I bridged the pads
quiet yarrow
around a minute after I bridged the pads
so you're still not following the procedure
did the step-by-step guide told you to "Wait for a minute then plug in the LiPo"
if it did, can you tell me what step it was? could you post a screenshot?
slim atlas
no but I already did all the betaflight stuff
quiet yarrow
no but I already did all the betaflight stuff
see step 9 of the unbricking procedure
slim atlas
OH MY GOD ITS BLINKING
I dont know what I just did I just unplugged it and replugged it and hten plugged in the lipo and I didnt hear fc or esc beeps but its blinking
its a quick flash but not rapid
I forgot to get an adapter for my new batteries and it died so if I dont get it in a few days ill return
slim atlas
@quiet yarrow I very thoroughly followed the steps and doing every single step and still has the same message
