I'm getting started and i think i installed the wrong software on the meteor 75 pro; i also need help binding it to the boxer
#Trouble binding Meteor 75 pro to a radiomaster boxer
tall anvil
granite torrent
I'm getting started and i think i installed the wrong software on the meteor 75 ...
go into the cli and execute the command version
post the output here
tall anvil
i don't know what you mean by cli could you be more specific
granite torrent
i don't know what you mean by cli could you be more specific
connect drone to betaflight configurator
go into the CLI tab
type in version into the text box at the bottom and press enter
copy-paste the output here
tall anvil
ok
granite torrent
and which "wrong software" did you installed?
tall anvil
version
Betaflight / STM32F411 (S411) 4.4.0 Feb 14 2023 / 05:25:45 (4605309d8) MSP API: 1.45
config: YES
board: manufacturer_id: BEFH, board_name: BETAFPVF411
granite torrent
close betaflight configurator, unplug usb.. for now
tall anvil
i searched for a youtube tutorial and tried to install a file with my binding phrase but i think i selected the wrong reciver for the drone
granite torrent
i searched for a youtube tutorial and tried to install a file with my binding ph...
https://www.expresslrs.org/quick-start/receivers/betafpv2400/
this is the updating guide..
FOLLOW this guide
should it complain of Target Mismatch, click on Flash Anyway
AS LONG AS you have selected the correct target from the configurator (betafpv AIO target)
use the same binding phrase you used/set into the boxer internal module when you flashed it and they should just autobind
tall anvil
ok got it
tall anvil
i got an error, this was the log
======== PASSTHROUGH INIT ========
Trying to initialize /dev/cu.usbmodem0x80000001 @ 420000
No CLI available. Already in passthrough mode?, If this fails reboot FC and try again!
======== RESET TO BOOTLOADER ========
- Using full duplex (CRSF)
Cannot detect RX target, blindly flashing!
esptool.py v4.2.1
Serial port /dev/cu.usbmodem0x80000001
WARNING: Pre-connection option "no_reset" was selected. Connection may fail if the chip is not in bootloader or flasher stub mode.
Connecting...
granite torrent
i got an error, this was the log
======== PASSTHROUGH INIT ========
Trying t...
what was the green LED on the board do?
If this fails reboot FC and try again!
step 1 of the guide says you should unplug-replug the fc and reboot it (unplug-replug lipo if you're plugging it in)
tall anvil
what was the green LED on the board do?
> If this fails reboot FC and try agai...
it was a solid green, wasn't flashing
granite torrent
it was a solid green, wasn't flashing
follow the procedure below
tall anvil
now the passthrough goes well, but i still get the "Cannot detect RX target, blinding flashing!"
granite torrent
now the passthrough goes well, but i still get the "Cannot detect RX target, bli...
have you changed anything on the flight controller configuration other than what's already stated?
e.g. did you changed the ports tab settings?
tall anvil
i think so i'll double check
tall anvil
have you changed anything on the flight controller configuration other than what...
i set everything right
tall anvil
follow the procedure below
the only thing i changed was telemetry as it was reported here to switch it off
granite torrent
the only thing i changed was telemetry as it was reported here to switch it off
you are "Exitting DFU mode"?
tall anvil
yes
jagged orchid
granite torrent
and which target did you flashed into it for it to end up soft-bricked?
tall anvil
tall anvil
and which target did you flashed into it for it to end up soft-bricked?
betaflight 2.4 AIO
granite torrent
can you try a different port or computer altogether?
granite torrent
betaflight 2.4 AIO
you mean betafpv aio RX.. ?
because, if you did things right, it should be working
tall anvil
yes rx
tall anvil
can you try a different port or computer altogether?
i can try another port