hello, i don't know how to ask this.. i'm very noob at fpv world. I have a meteor85 and a jumper tlite v2. Just worked 2 weeks ago normally, but suddenly stops to work without flying since this 2 weeks. The quad is not recieving signal, i think is not binded anymore. Can anyone help me? thank you i will appreciate it.
#Trying to bind the meteor85 with jumper tlite v2.
spark island
prisma sonnet
What version FC does your Meteor have? Connect to Betaflight, go to the CLI tab, and type version then post the output here.
spark island
thanks for the answer v-22
version
Betaflight / STM32F411 (S411) 4.4.2 Jun 3 2023 / 21:02:37 (23d066d08) MSP API: 1.45
config: YES
board: manufacturer_id: BEFH, board_name: BETAFPVF4SX1280
prisma sonnet
Ok, your FC has an SPI receiver and your are running Betaflight 4.4 which works with ELRS v3
Can you also post the output of get express in the Betaflight CLI, and then put your TX module into WiFi mode and show a screenshot of the !webui like this:
frozen runeBOT
Connect to your transmitter's or receiver's WiFi network to access the web UI:
spark island
get expres
expresslrs_uid = 87,152,95,67,41,209
Array length: 6
Default value: 0,0,0,0,0,0
expresslrs_domain = ISM2400
Allowed values: ISM2400, CE2400
expresslrs_rate_index = 0
Allowed range: 0 - 3
expresslrs_switch_mode = WIDE
Allowed values: WIDE, HYBRID
expresslrs_model_id = 255
Allowed range: 0 - 255
prisma sonnet
Your binding phrases do not match
prisma sonnet
Yes, you can change your TX binding phrase from the webui
And you can change your receiver binding phrase on the receiver tab in Betaflight
spark island
ok, i'm gonna do it now and i let u know
ok now the binding phrases matches
still not getting signal
prisma sonnet
Show the ELRS lua on your radio
SPI receivers do not currently support D, F, or full res modes. Make sure your packet rate is not set to something like F1000
Set it to "250Hz"
!spi
frozen runeBOT
https://www.expresslrs.org/hardware/spi-receivers/
Flight controllers with built-in ELRS SPI receivers are not flashed using ELRS Configurator, the ELRS firmware is "baked in" to Betaflight. Thus to update your ELRS firmware, you'll need to flash the latest version of Betaflight for your FC. Betaflight 4.3.x is compatible with ELRS v2.x.x, and Betaflight 4.4.x is compatible with ELRS v3.x.x.
To set a binding phrase on a SPI receiver, enter it here and paste the resulting code in the Betaflight CLI: https://www.expresslrs.org/hardware/spi-receivers/#binding-phrase
spark island
prisma sonnet
Lower TX power, or enable dynamic power
Then show screenshots of the webui and the output of get express again please
prisma sonnet
Dynamic on
spark island
get express
expresslrs_uid = 87,152,95,67,41,209
Array length: 6
Default value: 0,0,0,0,0,0
expresslrs_domain = ISM2400
Allowed values: ISM2400, CE2400
expresslrs_rate_index = 0
Allowed range: 0 - 3
expresslrs_switch_mode = WIDE
Allowed values: WIDE, HYBRID
expresslrs_model_id = 255
Allowed range: 0 - 255
prisma sonnet
These should be connecting
You said this was working then suddenly stopped? Are you sure the FC didn't get damaged?
Can you show some clear photos of both sides of the FC?
Can you also go into the BF CLI, type dump and paste the output here? I just want to make sure the config didn't get reset somehow
spark island
You said this was working then suddenly stopped? Are you sure the FC didn't get ...
yes, suddenly stopped. I dont fly since 2 weeks ago, but it worked before and i think it didn't get damaged
i take the photos in a moment of the FC and i'll send u
spark island
prisma sonnet
I don't see anything obviously wrong and your configuration looks ok
prisma sonnet
I'd try contacting BetaFPV support
https://discord.gg/hK7GcRCg
prisma sonnet
Please report back if you figure it out
prisma sonnet
Good luck