ripe harbor Nov 11, 2024, 2:59 AM

#

I can't figure out what setting to change. Everything is configured. Here is the error when I try to print from Prusa Slicer or OrcaSlicer

Error evaluating 'gcode_macro START_PRINT:gcode': gcode.CommandError: Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm.

Endstops:

#---------------------------------------------------- X -----------------------------------------------------

The X axis motor for the left toolhead, located at the rear left of the printer

#------------------------------------------------------------------------------------------------------------
[stepper_x]
dir_pin: x_dir_pin # Add ! in front of pin name to reverse the direction of stepper_x
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
homing_speed: 50
position_min: -60.60
position_max: 500
position_endstop: -60.60

#---------------------------------------------- DUAL_CARRIAGE -----------------------------------------------
[dual_carriage]
dir_pin: dual_carriage_dir_pin # Add ! in front of pin name to reverse the direction of dual_carriage
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
position_min: 0
position_max: 563.8
position_endstop: 563.8
safe_distance: 55

[stepper_y]
dir_pin: !y_dir_pin # Remove ! in front of pin name to reverse the direction of stepper_y
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
homing_speed: 50
position_min: -14.35
position_max: 533.65
position_endstop: -14.35

bed margins and parking

[gcode_macro RatOS]
variable_bed_margin_x: [60.6, 63.799999999999955]

[gcode_macro T0]
variable_parking_position: -58.6
Variable_loading_position: -35.6

[gcode_macro T1]
variable_parking_position: 561.8
Variable_loading_position: 538.8

keen tulipBOT Nov 11, 2024, 2:59 AM

#

To help others find answers, you can mark your question as solved via Right click solution message -> Apps -> ✅ Mark Solution

ripe harbor Nov 11, 2024, 2:59 AM

#

@cold topaz , I moved my tears to here.

cold topaz Nov 11, 2024, 8:15 AM

#

Toolhead x-offset is too high for the available parking space
you need to properly tune your endstop positions according to the comissioning guide

ripe harbor Nov 11, 2024, 3:17 PM

#

@cold topaz , I've tuned the T0 but T1 keeps being 511 then I adjust with the tool and when I test the change it still won't go back to the T1 edge.

#

best I've got so far:

[Variables]
idex_applied_offset = 0
idex_xcontrolpoint = 214.667355583814
idex_xoffset = -4.496388117184296
idex_ycontrolpoint = 529.7027809388774
idex_yoffset = -0.19168167161660676
idex_zcontrolpoint = -1.7859374999891466
idex_zoffset = -0.0059374999018411145
idex_zoffsetcontrolpoint = -5.392812499885313
nozzle_expansion_applied_offset = 0
nozzle_expansion_coefficient_multiplier = 1.0

#

i re-alinged the frame

cold topaz Nov 11, 2024, 3:18 PM

#

you also need to correctly calibrate the T1 endstop

ripe harbor Nov 11, 2024, 3:19 PM

#

I'll start over the T1 endstop goes exactly over the edge at -15. Over the middle of the edge like in the illustration.

cold topaz Nov 11, 2024, 3:19 PM

#

well, you are 5mm off

#

so one of the x endstops, or maybe both, are off

ripe harbor Nov 11, 2024, 3:20 PM

#

Ok i'll start over now

#

You said that i can just start from current values and don't need to start from default T0 and T1 endstop values, correct.

cold topaz Nov 11, 2024, 3:27 PM

#

yes

#

doesnt matter fro where oyu start

ripe harbor Nov 11, 2024, 3:36 PM

#

ok

#

T0 perfect

#

T1 511 pushed through config

#

#

adding to Printer.cfg now

#

also updating new bed pargin, park and load posistions at the same time

#

cold topaz Nov 11, 2024, 3:46 PM

#

still looks 4mm off

#

please run _VAOC_RESET and try again

ripe harbor Nov 11, 2024, 3:47 PM

#

I'm confused man. I run the tool and it actually keeps getting me further from the edge

cold topaz Nov 11, 2024, 3:48 PM

#

please run _VAOC_RESET this wil lreset any offset you have made

ripe harbor Nov 11, 2024, 3:48 PM

#

ok

cold topaz Nov 11, 2024, 3:48 PM

#

then redo the endstop calibration

#

you should have on both side about 60mm space, but your T1 says you have 4mm left, so there is something off

#

ripe harbor Nov 11, 2024, 3:49 PM

#

ok I reset

#

after reset the T1 stayed the same for edge and T0 improved.

#

Should I run VAOC now?

cold topaz Nov 11, 2024, 3:58 PM

#

yes

ripe harbor Nov 11, 2024, 3:59 PM

#

Thank you

#

[Variables]
idex_applied_offset = 0
idex_xcontrolpoint = 214.6200220041245
idex_xoffset = -0.8404594784860535
idex_ycontrolpoint = 529.6507166029694
idex_yoffset = -0.20826806528464203
idex_zcontrolpoint = -1.8800000000000003
idex_zoffset = 0.0
idex_zoffsetcontrolpoint = 0.0
nozzle_expansion_applied_offset = 0
nozzle_expansion_coefficient_multiplier = 1.0

#

let me do z offset now 🙂

#

@cold topaz , I was hitting my head on the table bro.

cold topaz Nov 11, 2024, 4:04 PM

#

ripe harbor <@910278846530596936> , I was hitting my head on the table bro.

thats not how you do a z-offset

ripe harbor Nov 11, 2024, 4:04 PM

#

its the z offset that makes you feel better by losing brain cells 🙂

#

Perfect toolhead z-offset of 0.011875mm!

You have a perfect toolhead z-offset!

#

time to print man!

#

I'll keep you up to date, let's see if it prints

ripe harbor Nov 11, 2024, 4:25 PM

#

@cold topaz , I'm checking prusa settings: Error evaluating 'gcode_macro _BEACON_APPLY_RUNTIME_MULTIPLIER:gcode': ZeroDivisionError: float division by zero

#

It printed first T0 then at swap it errorered with this 6x then stopped

#

I guessi should close this one and open another

#

ok

#

let me do that.

#v-core 4 idex 500 error: Error evaluating 'gcode_macro START_PRINT:gcode': gcode.CommandError: Toolh

The X axis motor for the left toolhead, located at the rear left of the printer