fix-my-printer

x stepper motor erratic behavior 5 messages

Jan 26, 2024, 4:38 AM motion Solved

4028-LÜFTERS 6 messages

Jan 25, 2024, 5:30 PM setup

extruder ratcheting noise 6 messages

Jan 25, 2024, 4:52 PM motion Solved

Inability to maintain Hotend and bed temps VC3.1 500 12 messages

Jan 24, 2024, 3:08 PM Solved other

Y homming fails 23 messages

Jan 23, 2024, 9:17 PM motion Solved setup

Temperature drops cause Klipper to hault 10 messages

Jan 23, 2024, 8:44 PM other

More troubles with a runout detector 17 messages

Jan 23, 2024, 1:15 PM Solved setup

hi everybody I have problems with my skew correction…. I can’t find this in my printer.cfg 7 messages

Jan 22, 2024, 3:17 PM other

Communication loss to DS18B20 4 messages

Jan 22, 2024, 12:50 PM Solved setup

Z homing issue 105 messages

Jan 21, 2024, 8:39 PM motion

need help with tachometer signal 2 messages

Jan 21, 2024, 12:53 PM other

Frame adjustment 2 messages

Jan 21, 2024, 2:42 AM setup

Reverse bowden easy to push hard to pull 6 messages

Jan 20, 2024, 3:32 PM other

Fully restarted after "START_PRINT" 15 messages

Jan 19, 2024, 8:27 PM other

ADC out of range 4 messages

Jan 19, 2024, 3:50 PM Solved other setup

Unable to read tmc uart 'stepper_z' register IFCNT 104 messages

Jan 19, 2024, 1:34 AM setup

Retries aborting: Probed points range is increasing. 5 messages

Jan 19, 2024, 12:08 AM Solved

Bond tech LGX Lite clicking 3 messages

Jan 17, 2024, 7:18 PM other

Lgx lite and rapido 2 constantly clogging. 24 messages

Jan 17, 2024, 9:26 AM other

Move out of range when performing Bed Mesh. 4 messages

Jan 17, 2024, 2:09 AM setup

Probable jam 2 messages

Jan 16, 2024, 11:05 PM other

XY-gantry (to) rigid 9 messages

Jan 15, 2024, 10:58 AM motion

I am done 7 messages

Jan 14, 2024, 4:47 PM other

[V-Minion] Strange noise when the Z-axis is going downward. 25 messages

Jan 14, 2024, 11:07 AM motion setup

Perpendicularity of four upper profiles 2 messages

Jan 12, 2024, 11:22 PM motion

Bed mesh not flat at all 2 messages

Jan 11, 2024, 11:32 PM motion setup

Loud buzzing sound coming from toolhead 7 messages

Jan 11, 2024, 10:15 PM motion

4028 running at 100% at 1-100 7 messages

Jan 11, 2024, 2:07 PM Solved setup

Endstop z still triggered after retract 2 messages

Jan 10, 2024, 8:22 PM setup

Orbiter v2 filament sensor on EBB36 4 messages

Jan 10, 2024, 2:16 PM setup

Internal Error on "G4" 2 messages

Jan 8, 2024, 5:11 PM other

Fan problems 7 messages

Jan 8, 2024, 1:56 PM setup

are 11 messages

Jan 8, 2024, 2:26 AM motion

what to select in printer.cfg? 5 messages

Jan 6, 2024, 11:06 PM setup

Mysterious "Lost communication with MCU 'mcu'" error began occuring out of the blue 5 messages

Jan 6, 2024, 10:45 PM other setup

Beacon Probe Causing Uneven First Layer? 17 messages

Jan 6, 2024, 1:53 AM other

homing issue 24 messages

Jan 4, 2024, 11:20 AM motion setup

V minion heater bed on the fritz 5 messages

Jan 2, 2024, 7:50 PM other

Question regarding changing thermistor sensor pin 3 messages

Jan 1, 2024, 8:01 PM other

Cannot get a consistent first layer distance. 22 messages

Dec 29, 2023, 3:34 PM setup

Getting More Consistent First Layer and Z Tilt Issue Related? 4 messages

Dec 28, 2023, 1:08 AM other

Thermistor wonky when N / L are switched 345 messages

Dec 27, 2023, 4:39 PM other setup

I accidentally cracked a magnet. 10 messages

Dec 27, 2023, 2:11 PM other

idk where the linear rail supposed to be….. 6 messages

Dec 26, 2023, 4:28 PM other

V Minion bed heater issues 2 messages

Dec 26, 2023, 4:21 AM other

Where to define pinouts for hotend and bed in RatOS? 2 messages

Dec 25, 2023, 11:43 AM setup

Unable to extrude (new printer) 12 messages

Dec 24, 2023, 9:20 PM setup

4028 Fan weirdness 3 messages

Dec 23, 2023, 10:14 PM setup

Loud rail sounds 13 messages

Dec 22, 2023, 7:07 PM motion setup

controller fan not shutting down 9 messages

Dec 21, 2023, 10:37 PM setup