fix-my-printer

ERROR c0130010 13 messages

Feb 12, 2024, 5:02 PM motion

mcu replacment 3 messages

Feb 12, 2024, 10:44 AM Solved other setup

Printer stops while priming nozzle 2 messages

Feb 12, 2024, 9:18 AM other

orbiter filament sensor setup? 4 messages

Feb 11, 2024, 10:35 PM setup

prints no longer start 7 messages

Feb 11, 2024, 6:53 PM Solved setup

Problems Configuring WebCam 6 messages

Feb 11, 2024, 1:16 PM setup

MCU protocol error on Octo pro 429 3 messages

Feb 10, 2024, 8:35 PM other

melted filament cleanup 5 messages

Feb 9, 2024, 3:19 PM other setup

extruder temp is reported wrong. phatus rapido uhf 18 messages

Feb 9, 2024, 1:24 PM other

issue with led ratrig. turn off my MCU after 10 sec or little more 6 messages

Feb 9, 2024, 5:57 AM setup

How bad is it? Aluminum bed. Cold. 4 messages

Feb 7, 2024, 2:15 AM other

VC3 400 with EBB42 invalid adxl345 id (got ff vs e5) 4 messages

Feb 6, 2024, 5:26 PM setup

Print stops randomly, Klipper reports shutdown 14 messages

Feb 6, 2024, 11:08 AM Solved other

probe adaptive meshing error 4 messages

Feb 5, 2024, 10:02 PM other setup

VC3 500 with EBB42 ttc errors 2 messages

Feb 5, 2024, 8:25 PM other

No access to Mainsail interface since full Ratos Update this AM 3 messages

Feb 5, 2024, 3:50 PM other

Heatbreak/Coldend Clog 4 messages

Feb 3, 2024, 12:02 PM other

LDO Super Power underperforming 7 messages

Feb 1, 2024, 9:58 AM motion Solved setup

Looking for code lines for a BTT Octopus max EZ 11 messages

Feb 1, 2024, 4:49 AM setup

s2vsb=1(ShortToSupply_B!) but file triggered !?? 3 messages

Feb 1, 2024, 3:22 AM motion other

fan_part_cooling_pin' is not a valid pin name on mcu 'mcu' 2 messages

Jan 31, 2024, 12:11 PM setup

Wobble V-core 400 417 messages

Jan 29, 2024, 8:36 PM motion

Raspberry and mother board crashed 14 messages

Jan 28, 2024, 2:21 PM Solved other

Heated Bed doesn´t heat up 4 messages

Jan 28, 2024, 11:28 AM Solved setup

Heated Bed Failure 17 messages

Jan 28, 2024, 2:50 AM Solved other

X-Axis Gantry Alignment 2 messages

Jan 26, 2024, 8:47 AM other

x stepper motor erratic behavior 5 messages

Jan 26, 2024, 4:38 AM motion Solved

4028-LÜFTERS 6 messages

Jan 25, 2024, 5:30 PM setup

extruder ratcheting noise 6 messages

Jan 25, 2024, 4:52 PM motion Solved

Inability to maintain Hotend and bed temps VC3.1 500 12 messages

Jan 24, 2024, 3:08 PM Solved other

Y homming fails 23 messages

Jan 23, 2024, 9:17 PM motion Solved setup

Temperature drops cause Klipper to hault 10 messages

Jan 23, 2024, 8:44 PM other

More troubles with a runout detector 17 messages

Jan 23, 2024, 1:15 PM Solved setup

hi everybody I have problems with my skew correction…. I can’t find this in my printer.cfg 7 messages

Jan 22, 2024, 3:17 PM other

Communication loss to DS18B20 4 messages

Jan 22, 2024, 12:50 PM Solved setup

Z homing issue 105 messages

Jan 21, 2024, 8:39 PM motion

need help with tachometer signal 2 messages

Jan 21, 2024, 12:53 PM other

Frame adjustment 2 messages

Jan 21, 2024, 2:42 AM setup

Reverse bowden easy to push hard to pull 6 messages

Jan 20, 2024, 3:32 PM other

Fully restarted after "START_PRINT" 15 messages

Jan 19, 2024, 8:27 PM other

ADC out of range 4 messages

Jan 19, 2024, 3:50 PM Solved other setup

Unable to read tmc uart 'stepper_z' register IFCNT 104 messages

Jan 19, 2024, 1:34 AM setup

Retries aborting: Probed points range is increasing. 5 messages

Jan 19, 2024, 12:08 AM Solved

Bond tech LGX Lite clicking 3 messages

Jan 17, 2024, 7:18 PM other

Lgx lite and rapido 2 constantly clogging. 24 messages

Jan 17, 2024, 9:26 AM other

Move out of range when performing Bed Mesh. 4 messages

Jan 17, 2024, 2:09 AM setup

Probable jam 2 messages

Jan 16, 2024, 11:05 PM other

XY-gantry (to) rigid 9 messages

Jan 15, 2024, 10:58 AM motion

I am done 7 messages

Jan 14, 2024, 4:47 PM other

[V-Minion] Strange noise when the Z-axis is going downward. 25 messages

Jan 14, 2024, 11:07 AM motion setup