fix-my-printer

VAOC no stream detected 7 messages

Mar 5, 2025, 3:07 AM Solved setup

I accidentaly took out the metal sheet on top of the bed when I was trying to put axes to home 19 messages

Mar 4, 2025, 7:44 PM setup

Lost communication with Toolboard 2 messages

Mar 4, 2025, 3:16 PM other setup

Printer stopping mid-print 104 messages

Mar 4, 2025, 2:46 PM other

Input Shaper bad Y 2 messages

Mar 3, 2025, 9:19 PM other

Smart sensor always showing empty, even though the LED switches to green just fine 9 messages

Mar 3, 2025, 6:36 PM Solved setup

Linear rail not sitting flat 3 messages

Mar 3, 2025, 4:54 PM motion

Move Out of Range Error When Measuring T1 Belt Tension 4 messages

Mar 3, 2025, 10:37 AM setup

What is this click moving x axis? A dead bearing? 17 messages

Mar 2, 2025, 3:32 PM motion Solved

IDEX - Nidec and Sanyo 4028 fans - different rpm 31 messages

Mar 2, 2025, 10:49 AM motion setup

Vcore 4 500mm heatbed stopped heating? 9 messages

Mar 2, 2025, 8:52 AM other

Print head juts along y when x is moved /vice versa 3 messages

Mar 2, 2025, 3:50 AM motion

After underextruding, we now enter the era of bleeding and overextruding! 4 messages

Mar 1, 2025, 8:23 PM other

Klipper reports ERROR. Fresh installation V-Core 4 Hybrid. 74 messages

Mar 1, 2025, 3:31 PM setup

Error with my ADXL 345 71 messages

Feb 28, 2025, 5:49 PM Solved other setup

Klipper reports: SHUTDOWN 19 messages

Feb 28, 2025, 1:44 PM other setup

No spi communication 20 messages

Feb 28, 2025, 8:34 AM motion setup

Dual_Carriage Endstop Always Triggered 4 messages

Feb 28, 2025, 7:52 AM motion other setup

Z not homing properly/ Beacon issue 5 messages

Feb 27, 2025, 5:02 PM motion Solved

VAOC safe_z value 5 messages

Feb 27, 2025, 11:36 AM motion other

Gantry misaligned after toolhead rebuild 3 messages

Feb 27, 2025, 5:46 AM motion

Swapped out BL Touch for RatRig 5V Induction Probe 40 messages

Feb 27, 2025, 1:19 AM other

V3.1 Catastrophic failure - massive layer shifts 20 messages

Feb 26, 2025, 7:17 PM motion Solved

Consistent hotend temperature offset 45 messages

Feb 26, 2025, 9:03 AM other

Input shaper error 18 messages

Feb 26, 2025, 5:22 AM setup

So I changed my Motor Mount and did new VAOC etc and now getting this. 4 messages

Feb 25, 2025, 10:14 PM other setup

prusa mini- klipper error 56 messages

Feb 25, 2025, 3:10 PM setup

Manual stepper motor issues 4 messages

Feb 24, 2025, 11:59 PM motion other

Freshly build. Can't move 10 messages

Feb 24, 2025, 10:12 PM setup

vaoc random deviation 3 messages

Feb 24, 2025, 9:32 PM motion

Belt tension all over the place 5 messages

Feb 24, 2025, 9:08 PM motion

Stepper Driver Overtemp Issue 10 messages

Feb 24, 2025, 3:42 PM Solved setup

Move out of range when unloading filament in T1 61 messages

Feb 24, 2025, 12:57 AM motion Solved

Fail when updating to RC3 8 messages

Feb 24, 2025, 12:49 AM Solved setup

4028 fan setup MantaM8P 1.1 7 messages

Feb 23, 2025, 9:19 PM setup

Commissioning issues 5 messages

Feb 23, 2025, 3:49 PM setup

Probe and Endstop Z always triggered 11 messages

Feb 22, 2025, 7:17 PM motion Solved setup

Vcore 4 400 IDEX Ratos STOP Button won't work 3 messages

Feb 22, 2025, 10:37 AM Solved other

Y axis stutters during movement 49 messages

Feb 21, 2025, 4:02 PM motion

vcore 3.1 500 Bed Mesh 9 messages

Feb 20, 2025, 10:57 PM setup

Bedmesh v4 500 7 messages

Feb 19, 2025, 11:59 PM other

camera setup logitech c920 42 messages

Feb 19, 2025, 7:10 PM setup

Leveling a warped Bed Mesh Vcore4 500mm 2 messages

Feb 19, 2025, 6:32 PM setup

bed mesh and first layer issues 6 messages

Feb 19, 2025, 6:01 AM other

I am at an absolute loss. Scratching noise coming from rear motor motor/bearings, V-Core 3.1 4 messages

Feb 19, 2025, 12:35 AM motion

Odd isssue now trying to run VAOC 3 messages

Feb 19, 2025, 12:00 AM other

Y axis homing in wrong direction 61 messages

Feb 18, 2025, 10:57 PM motion

Sensor 'extruder' temperature 45496.282 not in range - Differences in Rapido 2 Hotends? 4 messages

Feb 18, 2025, 2:47 PM other

PrintFarm OS 13 messages

Feb 18, 2025, 10:58 AM motion Solved setup

MCU 'toolboard_t0' shutdown: ADC out of range 29 messages

Feb 17, 2025, 5:48 PM Solved setup