ratos-support
can ERCF v2 work on RATOS 2.1
Configuration
Customization
Boards
MCU reporting incorrect temps
Boards
Connection via CANawa
Configuration
Customization
Boards
Other
Initial beacon calibration fails constantly...
Solved
Macros
Motion
Incomplete slicer config. used the default profile for v-core 4 500 hybrid in orca
Solved
Errors
Configuration
limit speed
Configuration
Customization
Motion
How do I create a new printer configuration?
Configuration
Customization
sensorless homing safe homing
Motion
RatOS 2.1 vc3.1 and connected to internet
Customization
Other
RatOS initial setup and configuration
Configuration
X axis inverted after upgrading from 1.2 to last release :
Solved
Configuration
Motion
Cant get RatOS working on a Voron2.4 with Euclid Probe to Set Z height
Boards
Motion
Adding parameters to END_PRINT
Solved
Macros
Customization
RatOS 2.1 Manta M5P Missing motor configuration in RatOS Configurator
Errors
Adding more Z steppers to config
Solved
Configuration
BEACON_INITIAL_CALIBRATION moves the head to incorrect place, crashing head
Solved
Errors
Macros
version mismatch
Configuration
4028 fan does not stop completely
Solved
Configuration
RatOS homing behavior
Solved
Errors
Configuration
Motion
Move exceeds maximum extrusion (2.673mm^2 vs 0.640mm^2)
Macros
RatOS 2.0 upgraded to v2.1.x - Custom V-Core 3.1 with Etched Foil bed heater w/ 3 combined sensors.
Solved
Configuration
Other
Errors
Customization
I'm confused about which version of RatOS to download.
Configuration
Beacon Rev H - Will not pass calibration. What is wrong?
Configuration
RatOs.cfg issu
Solved
Configuration
RatOS 2.x + Beacon ignoring configured offset and discarding offset at print end
Configuration
Outdated Beacon firmware
Solved
Configuration
Can't get input shaper setup 'Option 'accel_chip' is not valid in section 'resonance_tester''
Configuration
MCU shutdown; timer too close
Errors
RatOS-v2.1.0-RC2 How do I set configuration that is not included in the "Configurator"?
Configuration
Ratos 2.1 + Prusaslicer time estimate and layers N°
Solved
Configuration
Would an SSD (vs the SD card) speed up full updates on RPi 4B?
Configuration
Can not update MCU 'mcu' error after updating
Errors
Configuration
V Core-4 IDEX Klipper shutdown when trying to generate input shaper Graphs on toolhead 0
Solved
Errors
Configuration
Macros
Supported board but unsupported printer
Configuration
Boards
mellow board support
Configuration
Boards
WebRTC issues
Solved
Other
Pin 'J56' is not valid pin name on 'mcu'
Solved
Configuration
PB13 is reserved for spi2 on EBB42 v1. 2
Solved
Configuration
version mismatch, seems like a truncation issue?
Solved
Configuration
m8p+cb1 temp error after flash to can RatOs v2.0.2
Solved
Configuration
CANBUS running and mcu overridden but serial is restored in ratos.cfg after reboot
Solved
Configuration
Boards
Errors
Customization
2 in line extruders...
Solved
Customization
Change Wifi Settings for another network
Configuration
Why was primeline removed?
Configuration
Version mismatch warning while the version is the same
Boards
rc2 WiFi setup on pi4
Solved
Configuration
Error message with installing ADXL345 board.
Configuration
Significant Layer Shift on Multiple Printers
Motion
RatOS 2.1.0-RC2 Reporting that it cant write to stepper_x's Globalregister.
Configuration
Errors
Customization
Motion
System Upgrade Error
Configuration