Geprc tcube 18 elrs dji o4 Setup issue.

[frozen valve]

Hello there Folks i recently switched from analog to digital drones and i purchased my First little House Drone. I am having Trouble settings IT Up however. IT comes with onboard elrs which indont intend to use as i have Googles 3 and Controller 3. Steps i did so far. Updated Googles and Controller as per JB. Both are linked and calibrated( as i purchased the avata2 bundle before and Set all Up) i have linked Googles with the FC from that Drone( getting Video no prob), idid flash sbus Firmware to the Drone ,relinked with Googles. I did soldered the Missing 2 wires from dji cable AS geprc removed those for not having interference with elrs. Im seeing the Drone in betaflight ofc,colored Bars, but No Stick or Button movement,so i cant Setup the Drone. What am i Missing? Oh fast sbus has been activated also. Im lost

Analog drones wherent that complicate haha

[tranquil rain]

looks like you need to do this

[frozen valve]

So you mean since the external received ,the elrs was installed before , i have to resolder that? That has crossed my mind also already. Just BCS of Work i couldnt do that yet. Will Check in that Part of the FC once my Kids are in bed

Just checked my Pictures, i guess it is currently soldered

So with external Receiver the mean the dji and Not elrs

Kinda makes Sense

[tranquil rain]

doesnt matter what the receiver is, just as long as you arent using the onboard one you need to unbridge that jumper

[frozen valve]

Now as you are saying it IT totally makes Sense, i guess my mistake in thinking was that the external Receiver IS the elrs one.

Will Update later ! Thanks in advance for helping

[frozen valve]

It WAS the solderpoint, once removed, all showed up properly . In Germany we have a saying " Tomatoes on the eye "

[tranquil rain]

glad you got it sorted

[frozen valve]

Well not completely, i can setup all in betaflight, set arming etc, but no osd shows up and something is blocking the ARM itself as i just get the drone beeping when i try to arm it, but im closer, so i will figure it out eventually. If i wouldnt have to work now 😛

[tranquil rain]

can you grap a support id?

you will also need msp+display port enabaled under peripherals on uart 1

[frozen valve]

Will do that in my Lunchbreak in 4 hours now I have to do a little Bit of work haha

Thanks again for the help

*** Support data submitted ***
Id: "6e5da54b-5103-436d-a7db-e79b2006d2f3"

copy ID and provide to the betaflight tea

Did that quickly, Meetings are overrated

OSD Shows Up now after activated in uart1 peripherals

Still wont arm,getting a CPU overload Message when trying to arm

But another step closer at least

[frozen valve]

Most likely need to adjust pitloop frequency since im now fully using dji system

[tranquil rain]

8k4k dshot 300 will be what you have to run

maybe even 8k2k if you want to use bidirectional dshot

[frozen valve]

i have disabled unused features and indeed set it to 2k

drone arms now, but ofc runaway

but thats at least an easy fix chec king motors and directions

[frozen valve]

Neverending Story . Adjusted Motors yaw to 180, Drone Starts slowly to lift when pushing throttle, but soon goes into full throttle and ofc Crashes when i then disarm . Oh dji i hope you are worth the hazzle. When Testing all in betaflight without props,that doesnt Happen.

Weird and No Idea currently but well

[tranquil rain]

check prop and motor direction, board orentation and motor order

[frozen valve]

Yeah didbl all that as that was the First issue. When i arm, i can slowly start the Drone slowly Hover and then . Badush full throttle .

[frozen valve]

Currently im considering a full reflash and Setup from Scratch. Somewhere must be a mistake in the config

[frozen valve]

And what should i say, redoing all was the best idea.

I know what the issue was and well, i take the blame

I even resoldered the wires, bcs i thought, hey lets be sure

but the problem actually was

gyro orientation , after reflashing i had to set that

and well yaw 180 wasnt correct

After setting it to 180 first, i thought , mhh weird doesnt seem perfectly aligned with movement

after testing, 135

and she flys perfect now

How did jb alöways say " You gotta learn something today "

Thanks again @tranquil rain for your assistance !