#Binding Drone
tepid spade
rancid cedar
You do not configure it from there. That tab is for Analog and HDZero VTXs
The configuration of the DJI O3 air unit is done through the menu in the goggles once it's bound and connected
And binding the o3 to the goggles is pretty straight forward, look it up online, if you can't figure it out, let me know
tepid spade
You do not configure it from there. That tab is for Analog and HDZero VTXs
I’m trying to configure my uart but it’s saying to fix this first
rancid cedar
Is this a prebuilt quad?
That tab will not be available for DJI air units, you simply don't need it
However, it is important that the O3 can communicate using UART.
BUT if it is a prebuilt (assuming you haven't reflashed firmware), the ports should be already configured
tepid spade
It was a prebuilt but the ports tab got reset. I updated the firmware since I haven’t updated my drone in over a year and the connection was already lost and not binding. So I flashed new firmware and need to redo my UART
rancid cedar
Yeah you shouldn't update the firmware
Even if it has been years, if the drone is flying fine, no need to update anything, it resets everything
Find the CLI dump for your model of quad and version of betaflight, apply that
marsh mesa
It was a prebuilt but the ports tab got reset. I updated the firmware since I ha...
Did you cli dump all before you updated it?
tepid spade
Even if it has been years, if the drone is flying fine, no need to update anythi...
Yeah lesson learned 😂. Where woukd I find the CLI dump
tepid spade
Did you cli dump all before you updated it?
I did not but I did however do a backup before I flashed new firmware
marsh mesa
I did not but I did however do a backup before I flashed new firmware
Why don’t you just restore the dump then?
tepid spade
Why don’t you just restore the dump then?
I can try that, like I said. I’ve only been flying for a year and haven’t touched it for 6 months. Bit of a rookie at the moment
tepid spade
<@643111179685986305> Which quad is it?
rancid cedar
Which RC Link do you use, the DJI remote, ELRS or Crossfire?
tepid spade
ELRS with radiomaster boxer running a RM bandit micro
Used to bind perfect and now I’m having trouble since it’s been sitting.
rancid cedar
Alright, which method did you use to bind it?
tepid spade
Alright, which method did you use to bind it?
I created an ELRS profile withoin my boxer and put my drone into binding mode through Betaflight
My controllr is runing 3.3.2 and drone is on 4.5.1
rancid cedar
You should bind it using the binding phrase, by setting it on both the controller and the drone's receiver
Here's a video I made about how to do that:
https://youtu.be/wCY7rA4llqA
Try it and let me know if it works :)
Additionally, make sure that "Model Match" is off on both your radio (in the ExpressLRS Lua Script) and the Receiver (should be in the model tab of the Web interface)
tepid spade
Try it and let me know if it works :)
It looks like when I’m hitting save on my controller and my drone in RX and TX it’s not saving my binding phrase
rancid cedar
It looks like when I’m hitting save on my controller and my drone in RX and TX i...
Hmm, strange. Which is not saving, TX or RX?
tepid spade
Hmm, strange. Which is not saving, TX or RX?
Both....
rancid cedar
Are you sure it's not saving?
The text field will be always empty after refreshing
What it's actually doing is updating the UID bytes below
rancid cedar
Show me a screenshot
tepid spade
then i click save and binding phrase dissperars like you said but it doesnt actually chnage in the ()
rancid cedar
Wait
Is your drone 900Mhz?
Because the TX module you have is 900Mhz
it will only work with 900Mhz receivers
Most drones are actually 2.4Ghz