Tinkering with my first Voron

[unborn marten]

Hello everyone! Any help or advice would be greatly appreciated!

This is my first Voron build (self sourced) so if anything strikes you as odd, rest assured it’s because I don’t know what I’m doing.

I built this because I have always wanted to and I like tinkering with stuff. If anyone has any advice to move me towards better quality while maintaining speed or help me find what speed I can print with good quality, that would be fantastic. I almost entirely print parts for projects, so speed and accuracy would be nice.

Known issues:

• Not really sure what to do with the cable connecting to my hall effect sensor, so it's just kinda there.
• Belts might be too tight but this tension seemed to smooth out my shaper graphs so I left them.
• Polar angle energy profile is not symmetric.

Voron V2.4 300

• Nitehawk 36 ADXL345 mounted to extruder with two screws and standoffs
• Beacon
• Pin mod
• All Motors 24v
• Reaper Toolhead
• Belts tensioned by luck
• Z Motors are LDO-42STH48-2004AC(VRN) with tmc2209 drivers
• XY Motors are LDO-42STH48-2004MAH(VRN) with tmc5160 drivers

Thank you for taking the time, and I hope everyone has a good Friday!

[small bluff]

[small bluff]

Ping me or reply to this message once u are comfortable everything mentioned in the guidelines is fulfilled 👍

[unborn marten]

Hello! As far as I can tell I have everything.

[small bluff]

Perfect

Post looks very good. Thank u for taking the time, really makes our life easier

[small bluff]

Cube look’s good

U have VFAs at the upper and lower parts but no ringing

Install and configure TMC autotune, let me know if u need help or want a second pair of eyes double checking

[eager oar]

@unborn marten https://github.com/andrewmcgr/klipper_tmc_autotune

[unborn marten]

Perfect, I can do that! After that do I run through all the tests again and print a new cube? Unfortunately I need to go to sleep, so I'll have to do it in the morning.

[small bluff]

No rush, we will be here tomorrow, and even the the after tomorrow 😉

Only vibration profile

No cube yet

[unborn marten]

Roger, I'll get that taken care of, and update. Thank you!

[celest willow]

Turn off auto cooling and slow down for later times

[unborn marten]

https://tenor.com/view/odom-warpzone-its-him-shook-gif-18753284

[unborn marten]

Will do, and I'll update when its complete, thanks!

[unborn marten]

• disabled "Slow printing down for better layer cooling" Which is what I think you were telling me to do
• loosened both belts by 1/4 turn.

[small bluff]

Looks good in terms of ringing, nothing visible

see Reths writing above

[unborn marten]

Dropped PA from .04 to .03, seemed to help the corners a bit, dropped EM from .95 to .93 and the combination does seem better. Top is after PA and EM change, bottom is before.

[small bluff]

Graphs are clean
accel recommendation is in spec of a stock VORON
Print has no ringing

u are good to go 🙂

enjoy printing

always remember, the input shaper only limits outer walls

infill can be printed as fast as your hotend can keep up. 12k accel or more

inner walls can be printed faster than outer, how fast depends on your quality standards and how many walls.
obviously if u print just 2 walls and the inner one as ringing, u will see it on the outer one 😉

[unborn marten]

That makes sense! Thank you guys very much for all of the help, I really do appreciate it!

[small bluff]

very welcome.
for further print tuning u can also reach out to #slicers_and_print_help

[unborn marten]

WIll do, thank you!

And thank you @celest willow !

[small bluff]

just noticed we forgot to tell u

White ranges = Avoid

Green ranges = good, print in these.
always check in your slicer via the sliced preview if u print in a bad range.

iirc the latest Orca version has a "avoid those speeds" option somewhere

[unborn marten]

Roger that! I forgot to ask, is it not an issue that my polar angle is wonky?

[small bluff]

we always have to look at both sides of the paper sheet.

one is the graph
one is the print
thats why we request a VORON cube and not just the graphs 🙂

your print looks clean, so i would ignore it

get a serial number, then u have options to improve further 😉

[eager oar]

Submit a video to https://www.reddit.com/r/voroncorexy/. Read the pinned post for more info!

[unborn marten]

Thats a good point

I definitely want to get a serial. Out of curiosity, is getting a serial a requirement for anything?

[small bluff]

i wouldnt call it a requirement, however, if u get the VORON Owner discord server role here, a whole new world will open up for you 🙂
and also one world for improving further, beyond what we support here

getting the serial number will get u the server role here

highly worth it