Unknown temperature sensor | VORONDesign | Page 1

distant vine Jun 27, 2025, 8:02 AM

#

Inver ty firmware but not mrìe is somrtihnigVoron 3.4 350mm
Stealthburner, cnc tap chaotic alloweys red revs voron clockwork 2 ldo octopus pro 429 already insert siral I dont know other thing to of it give (Unknown temperature senso)
Buongiorno anche dopo ripetuti tentativi il firmware continua a dare problemi perché’ continua a dirmi: unknow temperature sensor.

frank kettle Jun 27, 2025, 8:05 AM

#

that's an interesting mix of english and italian 😅

#

"unknown temperature sensor" probably means you have a typographical error in your sensor_type field

distant vine Jun 27, 2025, 9:56 AM

#

whot can i do about it?

frank kettle Jun 27, 2025, 9:57 AM

#

distant vine whot can i do about it?

upload your klippy.log file so i can look at your config

distant vine Jun 27, 2025, 10:04 AM

#

i dont have it

frank kettle Jun 27, 2025, 10:05 AM

#

distant vine i dont have it

distant vine Jun 27, 2025, 10:06 AM

#

#

im realy sorry but wit tecnology and inglish im not good

frank kettle Jun 27, 2025, 10:08 AM

#

you may be better asking in #pizzaepasta-🇮🇹

distant vine Jun 27, 2025, 10:08 AM

#

📎 klippy.log

#

this?

frank kettle Jun 27, 2025, 10:08 AM

#

yes

#

well, one error cause will be you have no sensor_type defined in your [extruder] section

#

the same is also true for your [heater_bed] section

#

possibly there is something there, but "commented out" behind a # sign

distant vine Jun 27, 2025, 10:11 AM

#

i dont know whot to write to do more eesrror

frank kettle Jun 27, 2025, 10:11 AM

#

go and ask your fellow italians in #pizzaepasta-🇮🇹

distant vine Jun 27, 2025, 10:19 AM

#

#

frank kettle Jun 27, 2025, 10:20 AM

#

[temperature sensor hotend] is not a valid config section

#

sensor_type should be part of [extruder] and [heater_bed] as i have already said

distant vine Jun 27, 2025, 10:21 AM

#

can you gmi mr an an expele of good

#

?

frank kettle Jun 27, 2025, 10:22 AM

#

distant vine

this is now good for [heater_bed]

frank kettle Jun 27, 2025, 10:22 AM

#

distant vine

delete the line [temperature sensor hotend] here

distant vine Jun 27, 2025, 10:23 AM

#

ok

#

#

i knont now do more

frank kettle Jun 27, 2025, 10:25 AM

#

change the heater bed sensor_type to Generic 3950

distant vine Jun 27, 2025, 10:26 AM

#

same

frank kettle Jun 27, 2025, 10:28 AM

#

#   Type of sensor - common thermistors are "EPCOS 100K B57560G104F",
#   "ATC Semitec 104GT-2", "ATC Semitec 104NT-4-R025H42G", "Generic
#   3950","Honeywell 100K 135-104LAG-J01", "NTC 100K MGB18-104F39050L32",
#   "SliceEngineering 450", and "TDK NTCG104LH104JT1". See the
#   "Temperature sensors" section for other sensors. This parameter
#   must be provided.``` from the klipper3d documentation

#

i cannot see anywhere else in your config where temperature sensors are being mentioned

distant vine Jun 27, 2025, 10:31 AM

#

same

frank kettle Jun 27, 2025, 10:33 AM

#

can you upload your printer.cfg file to discord in case something is hiding from me

distant vine Jun 27, 2025, 10:34 AM

#

📎 printer-2.cfg

#

i knkow it volled printer.cfg

#

i dont knoe]w if it good for tap, i ave alredi switch z

frank kettle Jun 27, 2025, 10:36 AM

#

you have an extra section that i have deleted for you:

[extruder]
rotation_distance: 47.088
gear_ratio: 9:1
microsteps: 16

step_pin: PE2
dir_pin: PE3
enable_pin: !PD4
##    Update value below when you perform extruder calibration
##    If you ask for 100mm of filament, but in reality it is 98mm:
##    rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
##  22.6789511 is a good starting point
##    Update Gear Ratio depending on your Extruder Type
##    Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
##    Use 80:20 for M4, M3.1
full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
heater_pin: PA2
##    Validate the following thermistor type to make sure it is correct
#sensor_type: ATC Semitec 104NT-4-R025H42G (revo)
temperature_sensor hotend
sensor_type: ATC Semitec 104NT-4-R025H42G
pullup_resistor: 4700  # se la scheda usa una da 4.7k, altrimenti lascia defaulttemp  EPCOS 100K B57560G104F

# "Generic
#   3950","Honeywell 100K 135-104LAG-J01", "NTC 100K MGB18-104F39050L32",
#   "SliceEngineering 450", and "TDK NTCG104LH104JT1". See the
#   "Temperature sensors" section for other sensors. This parameter
#   must be provided.
min_temp: 10
max_temp: 270
max_power: 1.0
min_extrude_temp: 170
control = pid
pid_kp = 26.213
pid_ki = 1.304
pid_kd = 131.721
##    Try to keep pressure_advance below 1.0
pressure_advance: 0.05
##    Default is 0.040, leave stock
pressure_advance_smooth_time: 0.040```

distant vine Jun 27, 2025, 10:37 AM

#

same

frank kettle Jun 27, 2025, 10:37 AM

#

where did you get this config from?

distant vine Jun 27, 2025, 10:38 AM

#

i knodt remember

frank kettle Jun 27, 2025, 10:40 AM

#

it would be useful to know as i want to understand why they were redefining a sensor type that doesn't need redefining, and why the sensor pin was shown as J45

#

you might be better just to start from the beginning with one of these https://github.com/VoronDesign/Voron-2/tree/Voron2.4/firmware/klipper_configurations

GitHub

Voron-2/firmware/klipper_configurations at Voron2.4 · VoronDesign/...

Voron 2 CoreXY 3D Printer design. Contribute to VoronDesign/Voron-2 development by creating an account on GitHub.

distant vine Jun 27, 2025, 10:43 AM

#

thid they tond sfae file

frank kettle Jun 27, 2025, 10:43 AM

#

what does that mean

distant vine Jun 27, 2025, 10:44 AM

#

frank kettle Jun 27, 2025, 10:46 AM

#

it won't save if there's nothing to save

distant vine Jun 27, 2025, 10:57 AM

#

nothing to do

#

change someting?

#

or trash

frank kettle Jun 27, 2025, 11:01 AM

#

i would start with a new config as i have said earlier

#

there was junk in that one that should not be there

distant vine Jun 27, 2025, 11:01 AM

#

i lost the progecg

#

no hopr fp ,r thx

#Unknown temperature sensor