Help i cant connect to the raspberrypi? | VORONDesign | Page 1

frozen dust Feb 2, 2025, 12:20 AM

#

https://www.klipper3d.org/RPi_microcontroller.html

Be sure to enable spi

kindred sparrow Feb 2, 2025, 12:33 AM

#

did this and im still getting this error?

frozen dust Feb 2, 2025, 12:33 AM

#

Reboot the pi

#

Or comment out the adxl

kindred sparrow Feb 2, 2025, 12:37 AM

#

rebooted and commented out. same thing

#

#

here is my klippy log

📎 klippy_8.log

frozen dust Feb 2, 2025, 12:43 AM

#

Comment out MCU rpi

kindred sparrow Feb 2, 2025, 12:46 AM

#

It gets past that part but than beacon comes up. Beacon has to connect to the raspi

frozen dust Feb 2, 2025, 12:48 AM

#

Not that n

#

That is for old style adxl n

kindred sparrow Feb 2, 2025, 12:52 AM

#

oh ok. i did that and now im getting this

frozen dust Feb 2, 2025, 12:53 AM

#

kindred sparrow oh ok. i did that and now im getting this

Install beacon again from pi

kindred sparrow Feb 2, 2025, 12:53 AM

#

will do

#

same thing did not change?

#

frozen dust Feb 2, 2025, 1:00 AM

#

You shouldn't even have a probe section with beacon

#

https://github.com/EricZimmerman/Voron24/blob/master/config/beacon.cfg

GitHub

Voron24/config/beacon.cfg at master · EricZimmerman/Voron24

Voron 2.4 350 configuration files. LDOkit. Contribute to EricZimmerman/Voron24 development by creating an account on GitHub.

kindred sparrow Feb 2, 2025, 1:01 AM

#

i commented it out and same thing

#

#

frozen dust Feb 2, 2025, 1:02 AM

#

Are you guessing what to comment or not?

#

I shared a link to my config. For a 2.4. You can review it to see what you are missing

#

[probe]
z_offset = 1.200

Why?

kindred sparrow Feb 2, 2025, 1:03 AM

#

frozen dust Are you guessing what to comment or not?

no you said you dont need the probe section for beacon so i tried commenting it out to see if it would help.

frozen dust Feb 2, 2025, 1:03 AM

#

That's why it's complaining

#

You didn't comment out probe. You commented out z stepper

kindred sparrow Feb 2, 2025, 1:05 AM

#

frozen dust You didn't comment out probe. You commented out z stepper

oh damn i did not read fully. thats my bad

kindred sparrow Feb 2, 2025, 1:09 AM

#

frozen dust [probe] z_offset = 1.200 Why?

where did you see this?

frozen dust Feb 2, 2025, 1:10 AM

#

kindred sparrow where did you see this?

In klippy log

kindred sparrow Feb 2, 2025, 1:11 AM

#

im not %100 on that one to tell you the truth

frozen dust Feb 2, 2025, 1:12 AM

#

I mean it's there somewhere. Or in an include. Or in save config area

kindred sparrow Feb 2, 2025, 1:13 AM

#

i cant even find the pin in the probe section?

frozen dust Feb 2, 2025, 1:15 AM

#

Probably because you remove the probe section and it's sitting at the very bottom of printer.cfg in your safe config section

kindred sparrow Feb 2, 2025, 1:19 AM

#

i dont see it?

frozen dust Feb 2, 2025, 1:21 AM

#

What????

#

Line 1066

kindred sparrow Feb 2, 2025, 1:28 AM

#

i deleted it and that got me farther. thanks for helping me this far. now im getting this

frozen dust Feb 2, 2025, 1:29 AM

#

Search for probe

#

I would delete that saved mesh in your save config area too

Never save messes and never reuse meshes

kindred sparrow Feb 2, 2025, 1:38 AM

#

this is where i find it

frozen dust Feb 2, 2025, 1:40 AM

#

Show your beacon block. That's how mine looks for z

kindred sparrow Feb 2, 2025, 1:43 AM

#

This?

frozen dust Feb 2, 2025, 1:51 AM

#

No

[beacon]

kindred sparrow Feb 2, 2025, 1:54 AM

#

sorry

#

#

any ideas? i dont know where else to look?

#

Help i cant connect to the raspberrypi?

frozen dust Feb 2, 2025, 2:37 AM

#

I give up.

#

It's commented out

#Help i cant connect to the raspberrypi?