Trident Resonance Noob

[cunning helm]

Voron Trident 300 (LDO Kit Rev A)
ChaoticLab CNC Tap
Nitehawk SB ADXL345
Kinematic Bed
Belt tension measured using PF Maker Tension Meter, to 2.2 on the meter
Issue: Belt graphs are inconsistent and the top belt moves up and down during movements. This may not be a resonance issue, but rather a kinematics issue.

Pictures and video coming soon

[tough wigeon]

Also please post the picture of the VORON cube as stated in the guidelines

[tough wigeon]

Axes map is in beta still so not usable

[cunning helm]

Cubes incoming

Right now I have all the panels off and the steppers unplugged, I rechecked all the screws and measured the tension. The back corner are fine, It appears there is a mechanical issue with the front right idler. I already printed parts for the clee Beefy Front Idlers, so I will install that as soon as the dowel pins arrive and then recheck everything

[tough wigeon]

Pretty clean. Not seeing any ringing, do u?

Have u checked your XY joints according to the attached picture above?

[tough wigeon]

Could u also please share this cube with your slicer settings as a .3mf so we can import it and tell us which slicer was used please

[cunning helm]

Yes, thank you for that. I checked them after that print and after measuring to make those graphs. The right screw was at least one full turn away from touching the idler, even though it looked very low. I completely loosened all the screws and then readjusted them according to that guide, just in case.
Moving the axes by hand, it feels about the same as before. I also completely re-loosened the tensioners and re-did the tension using the PF Makers meter. They are now measuring 2.1 on the meter, within about +/- half the thickness of the marking line.

[cunning helm]

I also do not see ringing

[cunning helm]

I normallly use Cura, but I sliced the one for the picture in Orca. Here is the 3mf

Here is the accels I used

[forest needle]

in filament section do you have auto cool or slow down set? If so can you turn it off

[cunning helm]

I forgot to check that, I will check that for the next print. Today I got the dowels so I installed the Beefy Front Idlers, double checked the XY joints and the rear motor/idler mounts, and put everything back together.

Should I have input shaper on or off for the next cube?

Here is the webcam view of the cube printed immediately after re-assembly. I will not have access to the printer until Monday, but I can VPN in and mess around

[cunning helm]

It was set to slow down on overhangs, I disabled that just in case, here is the slice speed preview. I will send the results on Monday

[forest needle]

These cubes are not showing resonance.

[cunning helm]

Agreed

[forest needle]

You want slow down on overhangs on
You want auto cool off

[cunning helm]

Would you like me to send the latest belt graph?

[cunning helm]

Trident Resonance Noob

[forest needle]

Sure

[forest needle]

Question time:

Looks like you are printing good.
What is your goal?

[cunning helm]

I'm not sure anymore. I guess whatever resonance issues I had before are resolved now, though I'm not sure how or when or why. There was ringing just a couple weeks ago, and now there is no visible ringing. I am still having other issues which I am not sure if it is extrusion consistency, slicing, or kinematics, which would be a discuss for the print help channel I guess.
I found a lot of belt dust inside the right side front idler when I took them apart, and signs of wear on the edges of that belt, but doesn't necessarily relate to resonance.

[forest needle]

Some belt dust is normal.
If your belts start getting frayed that is another issue

[tough wigeon]

how are things going? do u need further help or can we mark this as solved?